Q27 粘结材料 标准查询与下载

NF T66-050-1:2011 沥青和沥青粘合剂.从沥青乳胶或缩减或溶剂沥青结合料中回收粘合剂.第1部分:蒸发回收.

Bitumen and bituminous binders - Recovery of binder from bituminous emulsion or cut-back or fluxed bitumous binders - Part 1 : recovery by evaporation.

BS EN 13074-2:2011 沥青和沥青粘合剂.从沥青乳液或缩减或焊剂沥青结合料回收粘合剂.用蒸发方法回收粘合剂的稳定性

Bitumen and bituminous binders. Recovery of binder from bituminous emulsion or cut-back or fluxed bituminous binders. Stabilisation after recovery by evaporation

DIN EN 12948:2011 石灰材料.干湿筛选法对粒度分布的测定;德文版本EN 12948-2010

This European Standard specifies two methods for the determination of the particle size distribution of liming materials. The dry sieving method (method A) is applicable to all liming materials except wet and paste-like products. Method A is not applicable, if blinding, caking, electrostatic charges or agglomeration occur on predrying. The wet sieving method (method B) is applicable to products which are susceptible to blinding, caking, electrostatic charges or agglomeration on pre drying.

Liming materials - Determination of size distribution by dry and wet sieving; German version EN 12948:2010

BS EN 459-1:2010 建筑用石灰.定义,规范和合格标准

Building lime. Definitions, specifications and conformity criteria

DIN EN 15275 Berichtigung 1:2011 结构粘合剂.土木工程和建筑结构中同轴金属组件用厌氧粘合剂的特性;德文版本EN 15275-2007,DIN EN 15275-2008-01的技术勘误,德文版本EN 15275-2007/AC-2010

Structural adhesives - Characterisation of anaerobic adhesives for co-axial metallic assembly in building and civil engineering structures; German version EN 15275:2007 , Corrigendum to DIN EN 15275:2008-01; German version EN 15275:2007/AC:2010

ASTM C1240-11 粘结混合料中使用的硅粉的标准规范

1.1 This specification covers silica fume for use in concrete and other systems containing hydraulic cement. 1.2 In the cases of slurried or densified silica fume, perform the tests on the raw silica fume from which these products have been made. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 The following safety hazards caveat pertains only to the test methods portions, Sections 10-19, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Read the material safety data sheets for materials used. 1.5 The text of this standard references notes and footnotes that provide explanatory information. These notes and footnotes (excluding those in tables) shall not be considered as requirements of this standard.

Standard Specification for Silica Fume Used in Cementitious Mixtures

ASTM D7519-11 反复浸湿后的纤维板和颗粒板的内部粘结强度和厚度膨胀的标准试验方法

These test methods provide a measure of the moisture resistance of cellulosic-based fiber and particle panels (for example, medium-density fiberboard (MDF), particleboard, and hardboard). This test methodology can be used to assess the thickness swelling and bond integrity characteristics of panels engineered for interior end-use applications involving exposure to cyclic temperatures and intermittent wetting environments. 1.1 These test methods provide a measure of the moisture resistance of cellulosic-based fiber and particle panels (for example, medium-density fiberboard (MDF), particleboard, and hardboard). Resistance to moisture changes is measured by dimensional and internal bond changes and does not refer to decay/mold resistance or other performance aspects. 1.2 These test methods do not address structural properties or performance following moisture exposure. Panels are subjected to repeated cycles of water submersion and oven drying. After three cycles, the test specimens are tested for thickness swelling (TS) and internal bond (IB) strength. nbsp;nbsp;nbsp; 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Internal Bond Strength and Thickness Swell of Cellulosic-Based Fiber and Particle Panels After Repeated Wetting

ASTM E874-11 保护板用非金属蜂窝状芯体铝盖面的粘合剂粘结标准规程

The formation of reproducible, durable-adhesive bonds in structural units requires great care in the selection of materials, the preparation of the surfaces of the parts to be bonded, and the performance of the steps in the bonding process. Experience has shown that adhesive bonding carried out in accordance with this practice produces relatively reproducible bonds. 1.1 This practice describes the materials, processes, and quality controls to be used in the manufacture of adhesive-bonded, aluminum-faced, nonmetallic-honeycomb-core sandwich panels for tactical shelters. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Adhesive Bonding of Aluminum Facings to Nonmetallic Honeycomb Core for Shelter Panels

ASTM C25-11 石灰石,生石灰和熟石灰化学分析的标准试验方法

These test methods provide accurate and reliable analytical procedures to determine the chemical constituents of limestone, quicklime, and hydrated lime (See Note 1). The percentages of specific constituents which determine a material''s quality or fitness for use are of significance depending upon the purpose or end use of the material. Results obtained may be used in relation to specification requirements. Because quicklime and hydrated lime quickly absorb water and carbon dioxide from the air, precision and bias are extremely dependent upon precautions taken during sample preparation and analysis to minimize excessive exposure to ambient conditions. Note 18212;These test methods can be applied to other calcareous materials if provisions are made to compensate for known interferences.1.1 These test methods cover the chemical analysis of high-calcium and dolomitic limestone, quicklime, and hydrated lime. These test methods are classified as either standard (preferred) or alternative (optional). 1.2 The standard test methods are those that employ classical gravimetric or volumetric analytical procedures and are typically those required for referee analyses where chemical specification requirements are an essential part of contractual agreement between buyer and seller. 1.3 Alternative or optional test methods are provided for those who wish to use procedures shorter or more convenient than the standard methods for the routine determinations of certain constituents. Optional test methods may sometimes be preferred to the standard test methods, but frequently the use of modern and expensive instrumentation is indicated which may not be accessible to everyone. Therefore, the use of these test methods must be left to the discretion of each laboratory. 1.4 The analytical procedures appear in the following order: Section Aluminum Oxide 15 Available Lime Index 28 Calcium and Magnesium Oxide: Alternative EDTA Titration Method 31 Calcium Carbonate Equivalent 33 Calcium Oxide: Gravimetric Method 16 Volumetric Method 17 Carbon Dioxide by Standard Method 22 Combined Oxides of Iron and Aluminum 12 Ferrous Iron Appendix X5 Free Calcium Oxide Appendix X6 Free Moisture in Hydrated Lime 21 Free Moisture in Limestone 20 Free Silica 29 Insoluble Matter Including Silicon Dioxide: Standard Method 8 Optiona......

Standard Test Methods for Chemical Analysis of Limestone, Quicklime, and Hydrated Lime

ASTM C1707-11 建筑用火山灰水硬石灰的标准规范

1.1 This standard covers four types of pozzolanic hydraulic lime for structural purposes which include use in mortar, scratch, brown, and finish (stucco) coats of interior or exterior plaster. 1.1.1 PHL8212;Pozzolanic hydraulic lime for use in mortar, scratch, brown, and finish (stucco) coats of interior or exterior plaster. 1.1.2 PHLc8212;PHL with a maximum 20 % binder weight of hydraulic cement. 1.1.3 PHL-A8212;Air-entrained PHL. 1.1.4 PHLc-A8212;Air-entrained PHLc. 1.2 This specification classifies pozzolanic hydraulic lime by minimum hydrated lime content, maximum hydraulic cement content, and specific performance requirements. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Pozzolanic Hydraulic Lime for Structural Purposes

ASTM C51-11 与石灰及石灰石相关的(工业用)标准术语

1.1 This terminology refers to the terms relating to lime and limestone products as used by the industry. 1.2 Where appropriate, the various terms defined below should be prefixed with one or other of the adjectives “high-calcium,” “magnesian,” or “dolomitic.” (Examples: dolomitic quicklime; high-calcium hydraulic hydrated lime; magnesian or dolomitic limestone.) 1.3 The composition of a limestone should be given in terms of a percentage of the carbonates present. In limestone of interest to the lime industry, it is usually assumed that the material consists almost entirely of carbonates. Where this assumption is not valid, the percentage of noncarbonate material should be determined, and the composition expressed in terms of the carbonate material present. 1.4 For specific application of lime or a limestone product, see the appropriate ASTM specification.

Standard Terminology Relating to Lime and Limestone (as used by the Industry)

ASTM C110-11 生石灰,熟石灰和石灰石的物理试验的标准试验方法

1.1 These test methods cover physical testing of quicklime and hydrated lime, and of limestone not otherwise covered in ASTM standards. Note 18212;Quicklime and hydrated lime have a high affinity for moisture and carbon dioxide. Caution should be taken to protect both hydrated and quicklime during sampling, storage, and testing (see Practice C50). 1.2 The test procedures appear in the following order: Section Air Entrainment 8 Apparent Loose Density of Hydrated Lime, Pulverized Quicklime, and Limestone 20 Apparent Packed Density of Hydrated Lime, Pulverized Quicklime, and Limestone 21 Autoclave Expansion of Hydrated Lime 9 Dry Brightness of Pulverized Limestone 12 Dry Screening by Air Jet Sieve 18 Fineness of Pulverized Quicklime and Hydrated Lime by Air Permeability 16 Limestone Grindability 13 Particle Size of Pulverized Limestone 17 Plasticity of Lime Putty 6 Popping and Pitting of Hydrated Lime 10 Residue and Sieve Analysis 15 Settling Rate of Hydrated Lime14 Slaking Rate of Quicklime 11 Specific Gravity of Hydrated Lime Products22 Standard Consistency of Lime Putty 5 Water Retention of Hydrated Lime 7 Wet Sieve Analysis of Agricultural Liming Materials19 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone

KS F 3204-2010 建筑用油性堵塞材料

이 표준은 건축물의 줄눈 부분, 섀시의 충전과 균열의 보수 등에 사용되는, 건축용 유성 코

Oil based caulking compounds for buildings

JG/T 298-2010 建筑室内用腻子

本标准规定了用于建筑室内用腻子的术语和定义、标记、要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用于以合成树脂乳液、聚合物粉末、无机胶凝材料等为主要粘结剂、配以填料、助剂等制成的室内找平用腻子。

Putty for interior

DIN EN 459-2:2010 建筑用石灰.第2部分:试验方法;德文版本EN 459-2-2010

Building lime - Part 2: Test methods; German version EN 459-2:2010

DIN EN 459-1:2010 建筑石灰.第1部分:定义,规范和符合性准则.德文版本EN 459-1-2010

Building lime - Part 1: Definitions, specifications and conformity criteria; German version EN 459-1:2010

BS EN 12948:2010 石灰材料.用干湿筛选法对粒度分布进行测定

This European Standard specifies two methods for the determination of the particle size distribution of liming materials. The dry sieving method (method A) is applicable to all liming materials except wet and paste-like products. Method A is not applicable, if blinding, caking, electrostatic charges or agglomeration occur after pre drying. The wet sieving method (method B) is applicable to products which are susceptible to blinding, caking, electrostatic charges or agglomeration after pre drying. Method B can be used to determine the primary particle size distribution of granulated products. Method B is not applicable to burnt lime and liming materials containing water-soluble constituents.

Liming materials. Determination of size distribution by dry and wet sieving

BS EN 459-2:2010 建筑石灰.试验方法

This European Standard describes the test methods for all building limes covered by EN 459-1-2010. This European Standard specifies the methods used for the chemical analyses and the determination of physical properties of building limes. This document describes the reference methods and, in certain cases, an alternative method which can be considered to be equivalent. In the case of a dispute, only the reference methods are used. Any other methods may be used provided they are calibrated, either against the reference methods or against internationally accepted reference materials, in order to demonstrate their equivalence.

Building lime. Test methods

NF P71-201-1-2:2010 建筑工程.内壁石膏灰浆.第1-2部分:材料选择的一般标准.

Building works - Internal gypsum plastering - Part 1-2 : general criteria for selection of materials.

EN ISO 4413:2010 液压流体动力.通用规则和安全要求系统及其组件(ISO 4413:2010)

Diese Internationale Norm enthält allgemeine Regeln und sicherheitstechnische Anforderungen an Hydraulikanlagen und deren Bauteile in Maschinen nach ISO 12100-1:2010, 3.1. Sie benennt Gefährdungen in Verbindung mit Hydraulikanlagen und legt Prinzipien fest, die anzuwenden sind, um jene Gefährdungen bei der bestimmungsgemäßen Verwendung der Anlage zu vermeiden. ANMERKUNG 1 Siehe Abschnitt 4 und Anhang A. Die wesentliche Gefährdung Lärm wird in dieser Internationalen Norm unvollständig behandelt. ANMERKUNG 2 Die Gefährdung Lärm hängt insbesondere von dem Einbau der Hydraulikbauteile oder -anlagen in die Maschine ab. Diese Internationale Norm gilt für die Konstruktion, den Bau und die Änderung von Anlagen und deren Bauteilen unter weiterer Berücksichtigung der folgenden Aspekte: a) Montage; b) Einbau; c) Einrichtung; d) störungsfreier Betrieb der Anlage; e) einfache und wirtschaftliche Instandhaltung und Reinigung; f) zuverlässiger Betrieb bei allen vorgesehenen Anwendungen; g) Energieeffizienz; und h) Umwelt.

Hydraulic fluid power - General rules and safety requirements for systems and their components