Q50 炭素材料综合 标准查询与下载

ARMY MIL-STD-814 D VALID NOTICE 1-2002 拴紧.检测和提取条款空降军用材料的要求

MIL-STD-814D, dated 3 February1997, has been reviewed and determined to be valid for use in acquisition.

REQUIREMENTS FOR TIEDOWN, SUSPENSION AND EXTRACTION PROVISIONS ON MILITARY MATERIAL FOR AIRDROP

ARMY MIL-HDBK-669 VALID NOTICE 1-2002 装卸台非法操纵的空降材料的装载环境和相关要求

MIL-HDBK-669, dated 3 February1997, has been reviewed and determined to be valid for use in acquisition.

LOADING ENVIRONMENT AND RELATED REQUIREMENTS FOR PLATFORM RIGGED AIRDROP MATERIAL

YB/T 4034-2001 高炉碳块尺寸及外观检查方法

Method for dimensions and aspect for the carbon block of blast furnaces

DIN 51913:2001 碳素材料检验.使用氦气比重瓶测定密度.固体材料

The document specifies a method for the determination of density ba gas pycnometer using helium as the measuring gas.

Testing of carbon materials - Determination of density by gas pycnometer (volumetric) using helium as the measuring gas - Solid materials

KS F 2519-2000 石材抗压强度试验方法

이 규격은 천연산 석재의 압축 강도 시험 방법에 대하여 규정한다.

Testing method for compressive strength of natural building stone

KS F 2530-2000 石材

이 규격은 주로 토목, 건축에 사용하는 천연산 석재에 대하여 규정한다. 다만, 천연 슬

Stones

DLA L-P-390 C NOTICE 2-2000 (低中号和高密度)聚乙烯和无规共聚物的成型和提取材料塑料 参考ASTM D 4976,ASTM D 4976 REV A,ASTM D 4976,ASTM D 4976,ASTM D 4976,ASTM D 4976 REV B,ASTM D 4976 REV A,ASTM D 4976,ASTM D 4976,ASTM

L-P-390C, dated 10 August 1971, is inactivated for new design and is no longer used, except for replacement purposes. Future acquisition for this product, when used in new design, should refer to ASTM D 4976, "STANDARD SPECIFICATION FOR POLYETHYLENE PLASTICS MOLDING AND EXTRUSION MATERIALS".

PLASTIC, MOLDING AND EXTRUSION MATERIAL, POLYETHYLENE AND COPOLYMERS (LOW, MEDIUM, AND HIGH DENSITY) [Refer To: ASTM D4976, ASTM D4976 REV A, ASTM D4976, ASTM D4976, ASTM D4976, ASTM D4976 REV B, ASTM D4976 REV A, ASTM D4976, ASTM D4976, ASTM D4976, AS

YB/T 910-2000 自焙碳块焙烧线收缩(或线膨胀)率.测定方法

Method for the detedrmination of the baked linear shrinkage (or linear expansion) ratio of self-baking carbon block

DIN 51919:1999 碳质材料试验.用电流电压法测定电极的电阻率.固体材料

The current voltage method is used for the determination of the electrical resistivity, measured in Ohm x ? of untreated carbon and graphite electrodes as well as treated carbon and graphite electrodes according to DIN 48601 at room temperature from 15 to 35 ?#,,#

Testing of carbonaceous materials - Determination of the electrical resistivity of electrodes according to the current-voltage method; solid materials

YS/T 286-1999 铝电解用普通阴极碳块

General cathode carbon brick for aluminum electrolysis

KS L 3403-1999 人造石墨圆筒形电极的螺纹精密度测定方法

이 규격은 인조 흑연 둥근형 전극(이하, 전극이라고 한다.)의 나사 정밀도 측정 방법에 대

Testing methods for screw precision of cylindrical machined graphite electrodes

JB/T 9580-1999 炭石墨.产品分类及型号编制方法

　　本标准规定了炭石墨产品分类原则和型号编制方法。 　　本标准适用于炭石墨产品。

Classification and type arrangement method of carbon-graphite products

DIN 51918:1999 炭素材料的试验.用浮力法测定松散密度并用水浸渍法测定开口孔隙率.固体物质

The method is used for the determination of the bulk density by buoyancy method, measured in g/cm, and the open porosity by impregnate with water, measured as volume fraction in %, of carbon and graphite materials (solid materials).

Testing of carbonaceous materials - Determination of bulk density by buoyancy method and the open porosity by impregnation with water - Solid materials

YS/T 411-1998 铝电解用预焙阳极、阳极糊二氧化碳反应性的测定方法

The measuring method of CO2 reaction of anode carbon,anode paste for aluminium electrolysis

YS/T 285-1998 铝电解用预焙阳极

Anode carbon for aluminium electrolysis

YS/T 284-1998 铝电解用阳极糊

Anode paste for aluminium electrolysis

ASTM D4018-99(2008) 碳及石墨纤维束的连续长丝抗拉特性的标准试验方法

The properties determined by these test methods are of value in material specifications, qualifications, data base generation, certification, research, and development. These test methods are intended for the testing of fibers that have been specifically developed for use as reinforcing agents in advanced composite structures. The test results of an impregnated and consolidated fiber should be representative of the strength and modulus that are available in the material when used as intended. The performance of fibers in different resin systems can vary significantly so that correlations between results using these test methods and composite testing may not always be obtained. The reproducibility of test results is dependent upon precise control over all test conditions. Resin type, content and distribution, curing process, filament alignment, gripping in the testing machine, and alignment in the testing machine are of special importance. The measured strengths of fibers are not unique quantities and test results are strongly dependent on the test methods used. Therefore the test method described here will not necessarily give the same mean strengths or standard deviations as those obtained from single filaments, dry fibers, composite laminas, or composite laminates.1.1 These test methods cover the preparation and tensile testing of resin-impregnated and consolidated test specimens made from continuous filament carbon and graphite yarns, rovings, and tows to determine their tensile properties. 1.2 These test methods also cover the determination of the density and mass per unit length of the yarn, roving, or tow to provide supplementary data for tensile property calculation. 1.3 These test methods include a procedure for sizing removal to provide the preferred desized fiber samples for density measurement. This procedure may also be used to determine the weight percent sizing. 1.4 These test methods include a procedure for determining the weight percent moisture adsorption of carbon or graphite fiber. 1.5 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Properties of Continuous Filament Carbon and Graphite Fiber Tows

DIN 51932:1998 炭素材料的试验.圆柱形机加工电极体积密度的测定

The document specifies a method for the determination of bulk density of cylindrically machined electrodes at room temperature between 15 and 35 ?

Testing of carbon materials - Determination of bulk density of cylindrically machined electrodes

DIN 51909:1998 碳素材料的试验.线性热膨胀系数的测定.固体材料

The document specifies a method for the determination of coefficient of linear thermal expansion of carbonaceous materials (solid materials) a temperatur between 20 and 1000 ?

Testing of carbon materials - Determination of coefficient of linear thermal expansion - Solid materials

DIN 51947:1998 含碳材料.术语

The document specifies terms for carbonaceous materials.

Carbonaceous materials - Terms