Q52 炭素材料 标准查询与下载

ASTM D3838-05 活性碳的pH值的标准试验方法

When a fluid containing an adsorbate is passed through a bed of activated carbon, chemical reactions may take place between the activated carbon, its other noncarbonaceous constituents, and the adsorbate containing fluid. The pH of the carbon may be a significant parameter of such a reaction and therefore may be an important characteristic of the carbon. 1.1 This test method covers determination of the pH of a water extract of activated carbon. 1.2 This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 6.

Standard Test Method for pH of Activated Carbon

BS ISO 12988-2:2004 铝生产用含碳材料.焙烧阳极.对二氧化碳反应性的测定.热解重量分析法

This test method covers the thermogravimetric (TGA) determination of CO2 reactivities and dusting of shaped carbon anodes used in the aluminium reduction industry. Many types of apparatus are available with a wide variety of thermal conditions, sample-size capability, materials of construction and procedures for determining the mass loss and subsequent rate of reaction. This test method standardizes the variables of sample dimensions, reaction temperature, gas velocity over the exposed surfaces, and reaction time such that results obtained on different types of apparatus are correctable.

Carbonaceous materials used in the production of aluminium - Baked anodes - Determination of the reactivity to carbon dioxide - Thermogravimetric method

KS M ISO 12982-1:2004 铝生产用碳质材料.煅烧焦炭.对空气活性的测定.第1部分:点火温度法

이 규격은 알루미늄 제조용 산화 양극 제조에 사용되는 하소된 석유 코크스의 공기에 대한

Carbonaceous materials used in the production of aluminium-Calcined coke-Determination of the reactivity to air-Part 1:Ignition temperature method

BS EN ISO 10618:2004 碳纤维.树脂浸渍纱拉伸性能的测定

ISO 10618:2004 specifies a method of test for the determination of the tensile strength, tensile modulus of elasticity and strain at maximum load of a resin-impregnated yarn specimen. The method is applicable to yarns (continuous and staple-fibre yarns) of carbon fibre for use as reinforcements in composite materials.

Carbon fibre - Determination of tensile properties of resin-impregnated yarn

ISO 10618:2004 碳纤维.树脂浸渍纱拉伸性能的测定

This International Standard specifies a method of test for the determination of the tensile strength, tensile modulus of elasticity and strain at maximum load of a resin-impregnated yarn specimen. The method is applicable to yarns (continuous and staple-fibre yarns) of carbon fibre for use as reinforcements in composite materials.

Carbon fibre - Determination of tensile properties of resin-impregnated yarn

DIN 51939:2004 碳素材料检验.煅烧焦碳中浮动焦碳成分的测定.固体材料

Testing of carbon materials - Determination of floating coke content in calcined coke - Solid materials

KS M ISO 8005:2003 铝生产用碳质材料.未煅烧和煅烧焦炭.灰分含量的测定

이 규격은 알루미늄 제조용 초록색의 하소 코크스 회분을 측정하는 방법에 대해 규정한다.

Carbonaceous material used in the production of aluminium-Green and calcined coke-Determination of ash content

BS 6043-1.1:2002 铝制造中使用的碳质材料的取样和测试方法 节距电极 采样 第 1.1 节：抽样

This International Standard specifies methods for sampling and preparing samples prior to testing of binder pitch used in the manufacture of electrodes for the electrolytic production of aluminium. These methods are applicable to grades of pitch in liquid or solid form, the latter having softening points higher than (determined according to the method specified in ISO 5940), in bulk, or in a number of containers making up one batch at sites of manufacture, storage, or delivery. Sampling methods and sampling plans for large consignments, or lots, of pitch in liquid form during the loading and unloading of ships are included.

Methods of sampling and test for carbonaceous materials used in aluminium manufacture. Electrode pitch. Sampling. Section 1.1: Sampling

BS 6043-3.9.1:2002 铝制造中使用的碳质材料的取样和测试方法 电极 预烘烤阳极对空气的化学反应性 通过质量损失法测定反应性

This part of ISO 12989 specifies a loss-in-mass method for the determination of the reactivity of carbonaceous products to air. The method was developed especially for anodes used in the production of aluminium.

Methods of sampling and test for carbonaceous materials used in aluminium manufacture. Electrodes. Chemical reactivity to air of prebaked anodes. Determination of the reactivity by a loss in mass method

BS ISO 10119:2002 碳纤维.测定密度

This International Standard specifies three methods for the determination of the density of carbon fibre yarn: — method A: liquid-displacement method; — method B: sink/float method; — method C: density-gradient column method. Method C is the reference method.

Carbon fibre - Determination of density

BS 6043-2.21.1:2001 铝制造中使用的碳质材料的取样和测试方法 电极焦 煅烧焦的空气反应性 通过测定着火温度来测定反应性 第2.21节：煅烧炭的空气反应性

This part of ISO 12982 describes an ignition temperature method for the determination of the reactivity to air of cal-cined petroleum coke used in the manufacture of anodes for the production of aluminium. A heating rate of 5 ℃/min is used for petroleum coke specifications, whereas 10℃/min is used for statistical process control of calcination kilns and for anode butt quality control. NOTE ISO 12982-2 (in preparation) will give a thermobalance method for the determination of the reactivity to air of calcined coke.

Methods of sampling and test for carbonaceous materials used in aluminium manufacture. Electrode coke. Air reactivity of calcined coke. Determination of the reactivity by determination of ignition temperature. Section 2.21: Air reactivity of calcined c...

YB/T 5289-2001 电极糊延伸率试验方法

The test method of extensibility of electrode paste

YB/T 2804-2001 普通高炉碳块

Carbon block for blast furnaces

BS 6043-3.8.1:2001 铝制造中使用的碳质材料的取样和测试方法 电极 预烘烤阳极的羧基反应性 通过质量损失法测定反应性

This part of ISO 12988 specifies a loss in mass method for the determination of the reactivity of carbonaceous products to carbon dioxide. This method was developed especially for baked anodes used in the production of aluminium.

Methods of sampling and test for carbonaceous materials used in aluminium manufacture. Electrodes. Carboxy reactivity of prebaked anodes. Determination of the reactivity by a loss in mass method

BS 6043-2.20.1:2001 铝制造中使用的碳质材料的取样和测试方法 电极焦 煅烧焦的羧基反应性 通过质量损失法测定反应性 第 2.20 节： 煅烧焦子的羧基反应性

This part of ISO 12981 specifies a method for the determination, by a loss in mass method, of the reactivity of calcined petroleum coke, used in the manufacture of anodes for the production of aluminium, to carbon dioxide.

Methods of sampling and test for carbonaceous materials used in aluminium manufacture. Electrode coke. Carboxy reactivity of calcined coke. Determination of the reactivity by a loss in mass method. Section 2.20: Carboxy reactivity of calcined coke Subs...

BS 6043-2-18:2001 铝制造中使用的碳质材料的取样和测试方法 电极焦 Eschka 法测定总硫

This International Standard specifies a reference method for determining the total sulfur content of calcined coke and calcined carbon products by the Eschka method, provided that they contain a minimum of 0,1 % by mass and prefer-ably less than 4 % by mass of sulfur.

Methods of sampling and test for carbonaceous materials used in aluminium manufacture. Electrode coke. Determination of total sulfur by the Eschka method

ISO 12982-1:2000 铝生产用碳素材料 煅烧焦 对空气反应性的测定 第1部分:灼烧温度法

This part of ISO 12982 describes an ignition temperature method for the determination of the reactivity to air of cal-cined petroleum coke used in the manufacture of anodes for the production of aluminium. A heating rate of 5 ℃/min is used for petroleum coke specifications, whereas 10 ℃/min is used for statistical process control of calcination kilns and for anode butt quality control. NOTE ISO 12982-2 (in preparation) will give a thermobalance method for the determination of the reactivity to air of calcined coke.

Carbonaceous materials used in the production of aluminium - Calcined coke; Determination of the reactivity to air - Part 1: Ignition temperature method

BS 6043-2.9:2000 制铝工业用含碳材料的取样和试验方法.电极焦炭.粒度分布的测定

This International Standard specifies a method for the determination of the particle size distribution of a sample of coke having a typical size distribution as normally produced by calcination of delayed petroleum coke. The same pro-cedure can be applied to consignments of calcined anthracite. This international Standard cannot be applied to frac-tions of carbon material prepared by sieving and crushing or to filter fines. This method is applicable to the determination of particle sizes ranging from 0,25 mm to 16 mm, as the sum of the percentages of the size distribution above and below this range is typically less than 10%. This International Standard is not applicable to determining particle sizes below 0,25 mm where a specific test for dust should be used.

Methods of sampling and test for carbonaceous materials used in aluminium manufacture - Electrode coke - Determination of particle size distribution

BS 6043-3.6:2000 铝制造中使用的碳质材料的取样和测试方法 电极 环境温度下阴极块和预烘烤阳极电阻率的测定

This International Standard specifies a method for the determination of the electrical resistivity of cathode blocks and baked anodes used in the production of aluminium, using samples at ambient temperature.

Methods of sampling and test for carbonaceous materials used in aluminium manufacture. Electrodes. Determination of electrical resistivity of cathode blocks and prebaked anodes at ambient temperature

BS 6043-3.4:2000 制铝工业用含碳材料的取样和试验方法.电极.用流体静力学法测定阴极碳块和预焙阳极的开放式孔隙率和体密度(表观密度)

This part of ISO 12985 specifies a hydrostatic method for the determination of the apparent density and the open (to water) porosity of carbonaceous products used in the production of aluminium. This hydrostatic method was developed principally to determine the open porosity but can also be used to measure the apparent density. This part of ISO 12985 is especially applicable to samples of complex on irregular geometry (due to drilling difficulties).

Methods of sampling and test for carbonaceous materials used in aluminium manufacture - Electrodes - Determination of the open porosity and bulk density (apparent density) of cathode blocks and prebaked anodes by a hydrostatic method