Q61 石棉材料 标准查询与下载

JC/T 211-2009 隔膜石棉布

本标准规定了隔膜石棉布的技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于用干法石棉纱、线机织而成的用于水电解槽隔离氢气与氧气的隔膜石棉布。

Asbestos cloth for insulation

JC/T 812-2009 泡沫石棉

本标准规定了泡沫石棉的术语和定义、产品标记、要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于使用温度在500℃内的保温隔热用泡沫石棉。

Foamed asbestos piece

JC/T 210-2009 石棉布、带

本标准规定了石棉布、带的分类与分级、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于机织石棉布、带。

Asbestos cloth & tape

JC/T 222-2009 石棉绳

本标准规定了石棉绳的分类与分级、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于以干法或湿法纺成的石棉纱、线制作的石棉绳。

Asbestos rope

ASTM E2356-09 综合建筑物石棉调查的标准实施规程

Management of asbestos-containing materials in buildings and facilities requires knowledge of the location, type, quantity, and condition of the material. The more complete and accurate the information available, the more appropriate and cost-effective are the control measures used to reduce possible exposure to airborne asbestos fibers. This is true whether the asbestos-containing materials remain undisturbed and completely intact, are selectively removed for maintenance or prior to renovation, or are removed to the greatest extent feasible before demolishing the building or facility. This practice describes three types of surveys that support different objectives. These are the Baseline Survey, the Project Design Survey, and the Pre-Construction Survey. The Baseline Survey is a building-wide or facility-wide inspection that provides a general sense of the overall location, type, quantity, and condition of asbestos-containing materials present. It is thorough in that most accessible functional spaces are inspected and bulk samples taken of suspect materials observed. The baseline survey provides information for long-term management of asbestos-containing materials and prioritization of response actions. The presence of asbestos in suspect materials may be assumed or presumed in some cases without bulk samples being taken or analyzed. However, the baseline survey is unobtrusive in that samples are not taken where doing so would result in objectionable damage to surfaces or where institutional barriers preclude access. In a baseline survey, destructive testing is avoided. Posting of signs and labels required for compliance with OSHA regulations would use the information generated during a Baseline Survey. Note 18212;A Baseline Survey is sometimes called an “AHERA” survey because it provides the type of information used for management of asbestos-containing materials in schools. However, the baseline survey described in this practice requires inspection, bulk sampling, quantification, and assessment of suspect materials that are excluded by virtue of their type and location from the AHERA regulations for schools. Note 28212;Suspect material subject to disturbance by planned or emergency maintenance may not always be identified as to asbestos content in a Baseline Survey. Collecting a single bulk sample, or a small number of samples, to determine if the material contains asbestos does not constitute a survey within the meaning of this practice. Nonetheless, the sample(s) should be collected in accordance with the methods described in Appendix X1 (this must be done by a properly-credentialed individual) and analyzed as set forth in 6.5. The Project Design Survey is more focused than a Baseline Survey and is used to provide information to the Project Designer for preparing abatement plans and specifications. The locations inspected are limited to the areas that will be affected by the abatement project. If the project is being done prior to renovation or demolition, the construction plans or at least a clear statement of the scope of the renovation or demolition work are required for a proper Project Design Survey. Destructive testing is often required for a Project Design Survey. The presence of asbestos in suspect materials is always confirmed in a Project Design Survey rather than being assumed or presumed. Other information required for the Project Design is collected during the survey. The Pre-Construction Survey is performed in anticipation of renovation or demolition where a Baseline Survey has not been conducted and there is no information, or insufficient information, as to the existence of asbestos-containing materials within the planned limits of construction. The Pre-Co..........

Standard Practice for Comprehensive Building Asbestos Surveys

JC/T 535-2007 硅灰石

本标准规定了硅灰石的分类、要求、试验方法、检验规则、标志、包装、运输和储存。 本标准适用于陶瓷、涂料、摩擦材料、密封材料、电焊条等领域使用的硅灰石。

Wollastonite

KS F 3701-2006 珍珠岩

이 규격은 단열재 및 흡음재의 원재료 등으로 사용되는 경량 골재인 펄라이트에 대하여 규

Perlite

JIS R 3453 AMD 1:2006 压缩纤维连接（修改件1）

JIS R 3453:2001を，次のように改正する。

Compressed fiber jointing (Amendment 1)

ASTM D6620-06 以计数为基础的石棉检测极限用标准实施规程

The DL concept addresses potential measurement interpretation errors. It is used to control the likelihood of reporting a positive finding of asbestos when the measured asbestos level cannot clearly be differentiated from the background contamination level. Specifically, a measurement is reported as being “below the DL” if the measured level is not statistically different than the background level. The DL, along with other measurement characteristics such as bias and precision, is used when selecting a measurement method for a particular application. The DL should be established either at the method development stage or prior to a specific application of the method. The method developer subsequently would advertise the method as having a certain DL. An analyst planning to collect and analyze samples would, if alternative measurement methods were available, want to select a measurement method with a DL that was appropriate for the intended application.5 The most important use of the DL, therefore, takes place at the planning stage of a study, before samples are collected and analyzed.1.1 This practice presents the procedure for determining the detection limit (DL) for measurements of fibers or structures using microscopy methods.1.2 This practice applies to samples of air that are analyzed either by phase contrast microscopy (PCM) or transmission electron microscopy (TEM), and samples of dust that are analyzed by TEM.1.3 The microscopy methods entail counting asbestos structures and reporting the results as structures per cubic centimeter of air (str/cc) or fibers per cubic centimeter of air (f/cc) for air samples and structures per square centimeter of surface area (str/cm2) for dust samples.

Standard Practice for Asbestos Detection Limit Based on Counts

ASTM D6620-06(2010) 基于计数测定石棉探测范围标准操作规程

The DL concept addresses potential measurement interpretation errors. It is used to control the likelihood of reporting a positive finding of asbestos when the measured asbestos level cannot clearly be differentiated from the background contamination level. Specifically, a measurement is reported as being “below the DL” if the measured level is not statistically different than the background level. The DL, along with other measurement characteristics such as bias and precision, is used when selecting a measurement method for a particular application. The DL should be established either at the method development stage or prior to a specific application of the method. The method developer subsequently would advertise the method as having a certain DL. An analyst planning to collect and analyze samples would, if alternative measurement methods were available, want to select a measurement method with a DL that was appropriate for the intended application. The most important use of the DL, therefore, takes place at the planning stage of a study, before samples are collected and analyzed.1.1 This practice presents the procedure for determining the detection limit (DL) for measurements of fibers or structures using microscopy methods. 1.2 This practice applies to samples of air that are analyzed either by phase contrast microscopy (PCM) or transmission electron microscopy (TEM), and samples of dust that are analyzed by TEM. 1.3 The microscopy methods entail counting asbestos structures and reporting the results as structures per cubic centimeter of air (str/cc) or fibers per cubic centimeter of air (f/cc) for air samples and structures per square centimeter of surface area (str/cm2) for dust samples. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Asbestos Detection Limit Based on Counts

BS PAS 60-3:2004 含石棉材料的受控清除设备.H类真空吸尘器的操作、清洁和保养.实施规程

This Publicly Available Specification(PAS)gives recommendations for the operation,cleaning and maintenance of class H vacuum cleaers in the controlled removal of asbestos-containing materials. It is not applicable to any other types of vacuum cleaner or applications.

Equipment used in the controlled removal of asbestos-containing materials - Operation, cleaning and maintenance of class H vacuum cleaners - Code of practice

BS PAS 60-1:2004 含石棉材料的受控清除设备.含石棉材料的受控润湿.规范

This PAS specifies requirements for equipment for the controlled wetting of asbestos-cotaining materials,via injection or spraying of liquid to suppress the release of airborne asbestos fibres. It is applicable to the wetting of asbestos-containing materials,via multipoint injuction or spraying,in insulating board(spraying only),sprayed coatings,thermal insulation and coatings on pipes, tanks and vessels.

Equipment used in the controlled removal of asbestos-containing materials - Controlled wetting of asbestos-containing materials - Specification

ASTM E2356-04e1 综合建筑物石棉调查的标准规程

1.1 This practice describes procedures for conducting comprehensive surveys of buildings and facilities for the purpose of locating, identifying, quantifying and assessing asbestos-containing materials.1.2 The results of a Comprehensive Building Asbestos Survey are intended to be used for ongoing management of asbestos-containing materials, including Operations Maintenance, removal and other response actions. This includes response actions associated with renovations. A Comprehensive Building Asbestos Survey is also intended to provide information required for removal of asbestos-containing materials prior to demolition of a building or facility.1.3 This standard practice discusses two types of surveys: Baseline Surveys and Project Design Surveys.1.4 This standard practice discusses the following activities for each of the above types of surveys:1.4.1 Planning the survey to meet defined objectives;1.4.2 Obtaining and reviewing information on the building or facility including previous surveys and response actions;1.4.3 Conducting the physical activities of inspecting the premises and collecting bulk samples of suspect materials;1.4.4 Analyzing the bulk samples for asbestos type and content;1.4.5 Assessing the Current Condition and Potential for Disturbance of asbestos-containing materials; and1.4.6 Preparing a report that includes a narrative discussion of the findings, tabulations of inspection, sampling and analysis results, graphical depiction of the areas inspected, and the results of the assessment.1.5 A Comprehensive Building Asbestos Survey provides sufficient information about the asbestos-containing materials in a building or facility for purposes of a real property transaction. In situations where the amount of information required by a party to the transaction is minimal, a Limited Asbestos Screen may suffice in place of the Comprehensive Building Asbestos Survey.1.6 This standard practice does not include air sampling or surface (dust) sampling for purposes of evaluating a potential exposure hazard from airborne asbestos fibers.1.7 Warning-Asbestos fibers are acknowledged carcinogens. Breathing asbestos fibers can result in disease of the lungs including asbestosis, lung cancer, and mesothelioma. Precautions in this standard practice should be taken to avoid creating and breathing airborne asbestos particles from materials known or suspected to contain asbestos. See for regulatory requirements addressing asbestos.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Comprehensive Building Asbestos Surveys

ASTM E2356-04 综合建筑物石棉调查的标准规程

1.1 This standard practice describes procedures for conducting comprehensive surveys of buildings and facilities for the purpose of locating, identifying, quantifying and assessing asbestos-containing materials.1.2 The results of a Comprehensive Building Asbestos Survey are intended to be used for ongoing management of asbestos-containing materials, including Operations Maintenance, removal and other response actions. This includes response actions associated with renovations. A Comprehensive Building Asbestos Survey is also intended to provide information required for removal of asbestos-containing materials prior to demolition of a building or facility.1.3 This standard practice discusses two types of surveys: Baseline Surveys and Project Design Surveys.1.4 This standard practice discusses the following activities for each of the above types of surveys:1.4.1 Planning the survey to meet defined objectives;1.4.2 Obtaining and reviewing information on the building or facility including previous surveys and response actions;1.4.3 Conducting the physical activities of inspecting the premises and collecting bulk samples of suspect materials;1.4.4 Analyzing the bulk samples for asbestos type and content;1.4.5 Assessing the Current Condition and Potential for Disturbance of asbestos-containing materials; and1.4.6 Preparing a report that includes a narrative discussion of the findings, tabulations of inspection, sampling and analysis results, graphical depiction of the areas inspected, and the results of the assessment.1.5 A Comprehensive Building Asbestos Survey provides sufficient information about the asbestos-containing materials in a building or facility for purposes of a real property transaction. In situations where the amount of information required by a party to the transaction is minimal, a Limited Asbestos Screen may suffice in place of the Comprehensive Building Asbestos Survey.1.6 This standard practice does not include air sampling or surface (dust) sampling for purposes of evaluating a potential exposure hazard from airborne asbestos fibers.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Comprehensive Building Asbestos Surveys

ASTM D299/D299M-04(2017) 石棉纱线的标准规格

1.1 This specification covers asbestos yarns having a minimum of 758201; % asbestos fiber by mass, excluding the mass of other inorganic reinforcing strands which may be present. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 Warning—Breathing of asbestos dust is hazardous. Asbestos and asbestos products present demonstrated health risks for users and for those with whom they come into contact. In addition to other precautions, when working with asbestos-cement products, minimize the dust that results. For information on the safe use of chrysoltile asbestos, refer to “Safe Use of Chrysotile Asbestos: A Manual on Preventive and Control Measures.”2 1.4 The following safety hazards caveat pertains only to the test methods, Section 13, described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See 1.3 for a specific safety hazard statement. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Asbestos Yarns

ASTM D299/D299M-04(2009)e1 石棉纱线的标准规范

1.1 This specification covers asbestos yarns having a minimum of 75 % asbestos fiber by mass, excluding the mass of other inorganic reinforcing strands which may be present. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 Warning—Breathing of asbestos dust is hazardous. Asbestos and asbestos products present demonstrated health risks for users and for those with whom they come into contact. In addition to other precautions, when working with asbestos-cement products, minimize the dust that results. For information on the safe use of chrysoltile asbestos, refer to “Safe Use of Chrysotile Asbestos: A Manual on Preventive and Control Measures.” 1.4 The following safety hazards caveat pertains only to the test methods, Section 13, described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See 1.3 for a specific safety hazard statement.

Standard Specification for Asbestos Yarns

ASTM C1121/C1121M-04(2009)e1 石棉的T/N湿度.长度分类标准试验方法

This test method provides a simple procedure for obtaining information on the fiber length distribution of suitable asbestos fiber. The use of relatively low cost apparatus, small test specimens, and a short test period, enhance the usefulness of this test method. Normally, results obtained by this test method are reproducible under comparable laboratory conditions. However, close agreement cannot be expected unless all deviations from the procedure, however minor, are avoided. Moreover, results for longer fiber grades are influenced to a greater extent by differences in fiber length distribution, and characteristics, than are those for shorter grades. This test is suitable for specification acceptance and manufacturing control. It is assumed that all undersized fibers, and only those, will pass through any given sieve aperture. However, this idealized condition is not normally achieved. Thus, results should not be misconstrued as true length distribution data.1.1 This test method covers the operation of the Turner and Newall (T and N) wet sieving classifier for asbestos, and a procedure for the determination of fiber length distribution and fines (defined in Terminology D2946) content of milled asbestos fiber (−74 μm [200 mesh]) sieve described in Specification E11. 1.2 For purposes of estimating length distribution, the test is limited to samples free from excessive quantities of non-fibrous particles or contaminants. Quantities exceeding 0.05 g retained in any given length fractions are considered excessive. 1.3 For comparisons between different fiber grades, only those specimens which have approximately the same degree of fiberization as determined by Test Methods D2752 will give completely meaningful results. 1.4 This test method is not applicable to ultrafine grades of asbestos powders which contain little or no fibers retained on a 74-μm [200 mesh] sieve. This method is restricted to Quebec Standard grades 4A to 7D inclusive as determined by Test Method D3639. Note 18212;This is an alternative procedure to Test Method D2589. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6 Warning—Breathing of asbestos dust is hazardous. Asbestos and asbestos products present demonstrated health risks for users and for those with whom they come into contact. In addition to other precautions, when working with asbestos-cement products, minimize the dust that results. For information on the safe use of chrysoltile asbestos, refer to “Safe Use of Chrysotile Asbestos: A Manual on Preventive and Control Measures.” 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety an......

Standard Test Method for Turner and Newall (T and N) Wet-Length Classification of Asbestos

ASTM D299-04e1 石棉纱的标准规范

1.1 This specification covers asbestos yarns having a minimum of 75 % asbestos fiber by mass, excluding the mass of other inorganic reinforcing strands which may be present.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 Warning-Breathing of asbestos dust is hazardous. Asbestos and asbestos products present demonstrated health risks for users and for those with whom they come into contact. In addition to other precautions, when working with asbestos-cement products, minimize the dust that results. For information on the safe use of chrysoltile asbestos, refer to "Safe Use of Chrysotile Asbestos: A Manual on Preventive and Control Measures."1.4 The following safety hazards caveat pertains only to the test methods, Section , described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See 1.3 for a specific safety hazard statement.

Standard Specification for Asbestos Yarns

ASTM D299-04 石棉纱的标准规范

1.1 This specification covers asbestos yarns having a minimum of 75 % asbestos fiber by mass, excluding the mass of other inorganic reinforcing strands which may be present.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 The following safety hazards caveat pertains only to the test methods, Section 13, described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Asbestos Yarns

ASTM C1121-04e1 石棉的T/N湿度-长度分类标准试验方法

This test method provides a simple procedure for obtaining information on the fiber length distribution of suitable asbestos fiber. The use of relatively low cost apparatus, small test specimens, and a short test period, enhance the usefulness of this test method. Normally, results obtained by this test method are reproducible under comparable laboratory conditions. However, close agreement cannot be expected unless all deviations from the procedure, however minor, are avoided. Moreover, results for longer fiber grades are influenced to a greater extent by differences in fiber length distribution, and characteristics, than are those for shorter grades. This test is suitable for specification acceptance and manufacturing control. It is assumed that all undersized fibers, and only those, will pass through any given sieve aperture. However, this idealized condition is not normally achieved. Thus, results should not be misconstrued as true length distribution data.1.1 This test method covers the operation of the Turner and Newall (T and N) wet sieving classifier for asbestos, and a procedure for the determination of fiber length distribution and fines (defined in Terminology D 2946) content of milled asbestos fiber (74 m (200 mesh)) sieve described in Specification E 11.1.2 For purposes of estimating length distribution, the test is limited to samples free from excessive quantities of non-fibrous particles or contaminants. Quantities exceeding 0.05 g retained in any given length fractions are considered excessive.1.3 For comparisons between different fiber grades, only those specimens which have approximately the same degree of fiberization as determined by Test Methods D 2752 will give completely meaningful results.1.4 This test method is not applicable to ultrafine grades of asbestos powders which contain little or no fibers retained on a 74-m (200 mesh) sieve. This method is restricted to Quebec Standard grades 4A to 7D inclusive as determined by Test Method D 3639. Note 1This is an alternative procedure to Test Method D 2589.1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.6 Warning-Breathing of asbestos dust is hazardous. Asbestos and asbestos products present demonstrated health risks for users and for those with whom they come into contact. In addition to other precautions, when working with asbestos-cement products, minimize the dust that results. For information on the safe use of chrysoltile asbestos, refer to "Safe Use of Chrysotile Asbestos: A Manual on Preventive and Control Measures."This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement, see .

Standard Test Method for Turner and Newall (T and N) Wet-Length Classification of Asbestos