T31 紧固件 标准查询与下载

SAE J429-2014 外螺纹紧固件的机械和材料要求

This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems , and U-bolts in sizes to 1-1/2 in. inclusive. The term stud as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts. The mechanical properties included in Table 1 were compiled at an ambient temperature of approximately 20 °C (68 °F). These properties are valid within a temperature range which depends upon the material

Mechanical and Material Requirements for Externally Threaded Fasteners

QC/T 258-2013 汽车车轮 螺母座强度试验

本标准规定了汽车车轮螺母座强度的试验方法和性能要求。本标准适用于螺母座呈凸起形状的汽车车轮。

Vehicle wheels- Nut seat strength tests

SAE J2277-2013 喷丸覆盖面的测定

This SAE Recommended Practice provides procedures some procedure for determining shot penning coverage and relating coverage to part exposure to the media stream.. Effectiveness of shot peening is directly dependent on coverage. Either incomplete or excessive coverage may be detrimental to fatigue strength and life.

Shot Peening Coverage Determination

SAE J663-2013 制动块卡车和公共汽车制动片和螺栓用铆钉

This document has been declared ""Stabilized"" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Standard specifies the dimensions of semitubular rivet and bolts for brake linings/blocks.

Rivets for Brake Linings and Bolts for Brake Blocks Truck and Bus

SAE J429-2013 外螺纹紧固件的机械和材料要求

"This SAE Standard covers the mechanical and material requirements for inch-series steel bolts@ screws@ studs@ screws for sems1@ and U-bolts2 in sizes to 1-1/2 in. inclusive. The term ""stud"" as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed@ collared@ or similar products which are more closely characterized by requirements shown herein for bolts. The mechanical properties included in Table 1 were compiled at an ambient temperature of approximately 20 ??(68 ??. These properties are valid within a temperature range which depends upon the material grade used and thermal and mechanical processing. Other properties such as fatigue behavior@ corrosion resistance@ impact properties@ etc.@ are beyond the scope of this document and responsibility for ensuring the acceptability of the product for applications where conditions warrant consideration of these other properties shall be borne by the end user."

Mechanical and Material Requirements for Externally Threaded Fasteners

QC/T 369-2013 多管夹片

本标准规定了多管夹片的型式与尺寸、技术条件。本标准适用于夹持管径D为6mm~18mm、夹持管子根数为2个~6个的多管夹片。

Pipe clips.Fasten multipipe

QC/T 621.3-2013 钢带式弹性软管夹箍 第3部分：夹箍用软管和接管

本部分规定了夹箍用软管和接管的尺寸及结构形式。本部分适用于符合QC/T 621.1规定的钢带式弹性软管夹箍连接的软管和接管。

Spring band hose clamps.Part 3:Hose and spigot for clamps

QC/T 621.2-2013 钢带式弹性软管夹箍 第2部分：技术条件

本部分规定了钢带式弹性软管夹箍的技术条件。本部分适用于QC/T 621.1规定的钢带式弹性软管夹箍。

Spring band hose clamps.Part 2:Technical conditions

QC/T 599-2013 端面凸焊螺栓

本标准规定了端面凸焊螺栓的型式与尺寸、技术条件。本标准适用于螺纹规格为M4~M12、机械性能等级为5.8和8.8的汽车用A型端面凸焊螺栓和B型端面凸焊螺栓。

Overhead projection weld bolts

QC/T 621.1-2013 钢带式弹性软管夹箍 第1部分：型式、尺寸和材料

本部分规定了钢带式弹性软管夹箍的型式、尺寸和材料。本部分适用于由调质弹簧钢制造的,用于在汽车上固定软管与接管联结的夹箍。本部分规定的夹箍适用温度为-40℃~150℃,常用于:——冷却循环系统和压强小于300kPa的伺服系统;——压强小于700kPa的燃油系统;——负压进气系统;——压强小于200kPa的进气系统。

Spring band hose clamps.Part 1:Types,dimensions, materials

QC/T 618-2013 嵌装塑料螺母技术条件

本标准规定了汽车用嵌装塑料螺母的要求、试验方法、验收检查及标志与包装。本标准适用于与塑料(尼龙)用自攻螺钉相配的嵌装塑料螺母。

Specification for plastic expansion nut

QC/T 518-2013 汽车用螺纹紧固件紧固扭矩

本标准规定了汽车用螺纹紧固件紧固扭矩。本标准适用于符合以下条件,以控制扭矩方式进行的紧固:——外螺纹件的机械性能符合GB/T 3098.1规定的8.8、10.9和12.9级;——内螺纹件的机械性能符合GB/T 3098.2或GB/T 3098.4,且具有充分发挥螺纹连接副承载能力的强度;——内、外螺纹件的六角对边尺寸符合GB/T 3104规定的标准系列;——螺栓-螺母连接副以及螺栓-螺母以外的螺纹连接副;——螺纹符合GB/T 196,螺纹精度不低于GB/T 197规定的6级;——外螺纹件在紧固中承受轴向拉伸载荷;——螺栓或螺钉的设计拉力采用屈服点σs或屈服强度σ0.2的90%。本标准不适用于外螺纹件在紧固中承受压缩力的紧定螺钉、由外螺纹件攻出螺纹的自攻螺钉及木螺钉、采用弹簧垫圈或弹性垫圈的螺纹紧固件以及有效力矩型螺纹紧固件的紧固。

Tightening torque for automotive threaded fasteners

QC/T 370-2013 单管夹片

本标准规定了单管夹片的型式与尺寸、技术条件。本标准适用于夹持管径D为5mm~25mm的单管夹片。

Pipe clips.Fasten one pipe

SAE J485-2013 开口销用螺栓孔与螺母螺杆尾和槽

SAE J485 specifies the recommended nominal diameters and locations of holes in bolt or screw shanks, and nominal widths and depths of slots in nuts, for use with the recommended sizes of inch-series cotter pins, as shown.

Holes in Bolt and Screw Shanks and Slots in Nuts for Cotter Pins

SAE J492-2013 铆钉选择和设计依据指南

This is a guide intended to aid the user in the proper selection and application of rivets as a fastening means. It consists of general information on the advantages of riveting, various methods of riveting, selection of rivets and design considerations.

Guide for Rivet Selection and Design Consideration

SAE J891-2013 弹簧螺母

Included herein are complete general and dimensional specifications for metric and inch types of spring nuts recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw is considered adequate for the application. It should be noted that spring nuts having other configurations, dimensions, provisions for ground, etc., are available and manufacturers should be consulted.

Spring Nuts

SAE J892M-2013 推进式弹簧螺母公制系列通用规格

Included herein are general, dimensional, and performance specifications for those typies, styles, and sizes of steel stamped Push-On Spring Nuts recognized as SAE standard. These nuts are intended for general use where the engagement of the mating metal or plastic studs and in some cases screw or bolt threads if considered adequate for the fastening joint appalications. It should be noted that Push-On Spring Nuts having other characteristics and configurations are available and manufacturers should be consulted. For the inch equivalent of this document, see SAE J892.

Push-On Spring Nuts Metric Series General Specifications

SAE J892-2013 推进式弹簧螺母公制系列通用规格

Included herein are general, dimensional, and performance specifications for those typies, styles, and sizes of steel stamped Push-On Spring Nuts recognized as SAE standard. These nuts are intended for general use where the engagement of the mating metal or plastic studs and in some cases screw or bolt threads if considered adequate for the fastening joint appalications. It should be noted that Push-On Spring Nuts having other characteristics and configurations are available and manufacturers should be consulted. For the metric equivalent of this document, see SAE J892M.

Push-On Spring Nuts Inch Series General Specifications

SAE J430-2013 非螺纹紧固件碳钢实心铆钉英制系列用机械和化学要求

These specifications cover the mechanical and chemical requirements, and surface discontinuities limits for carbon steel solid rivets used in automotive and other related industries.

Mechanical and Chemical Requirements for Nonthreaded Fasteners Carbon Steel Solid Rivets Inch Series

SAE J238-2013 螺母和锥形弹簧垫圈组件

This SAE Standard covers general, dimensional data, and methods of test for two types of general purpose nut and conical spring washer assemblies, designated Type LN and Type HN, intended for mass production and other operations where speed and convenience are paramount factors.

Nut and Conical Spring Washer Assemblies