T32 螺塞、管件 标准查询与下载

QC/T 383-2013 六角头锥形磁性螺塞

本标准规定了六角头锥形磁性螺塞的型式与尺寸、技术条件。本标准适用于螺纹规格为NPT3/8~NPT1½的汽车用六角头锥形磁性螺塞。

Hexagon outside head cone plugs with magnetic core

QC/T 402-2013 卡套式锥螺纹三通接头体

本标准规定了卡套式锥螺纹三通接头体的型式与尺寸、技术条件。本标准适用于管子外径为4mm~35mm,最大工作压力10MPa~25MPa的汽车用油、气及一般腐蚀介质的管路系统。

24°cone connectors.Male branch tee.Body

QC/T 405-2013 扩口式锥螺纹三通管接头体

本标准规定了扩口式锥螺纹三通管接头体的型式与尺寸、技术条件。本标准适用于管子外径为5mm~12mm,最大工作压力12MPa~16MPa的汽车用油、气及一般腐蚀介质的管路系统。

Flared couplings.Male branch tee.Body

QC/T 403-2013 扩口式锥螺纹直通管接头体

本标准规定了扩口式锥螺纹直通管接头体的型式与尺寸、技术条件。本标准适用于管子外径为5mm~12mm,最大工作压力12MPa~16MPa的汽车用油、气及一般腐蚀介质的管路系统。

Flared couplings.Male.Body

QC/T 378-2013 内六角锥形螺塞

本标准规定了内六角锥形螺塞的型式与尺寸、技术条件。本标准适用于螺纹规格为NPT1/8~NPT1¼的汽车用内六角锥形螺塞。

Hexagon countersunk headless cone plugs

QC/T 399-2013 卡套式锥螺纹直通接头体

本标准规定了卡套式锥螺纹直通接头体的型式与尺寸、技术条件。本标准适用于管子外径为4mm~35mm,最大工作压力10MPa~25MPa的汽车用油、气及一般腐蚀介质的管路系统。

24° cone connectors.Male.Body

QC/T 381-2013 六角头锥形螺塞

本标准规定了六角头锥形螺塞的型式与尺寸、技术条件。本标准适用于螺纹规格为NPT1/8~NPT1的汽车用六角头锥形螺塞。

Hexagon outside head cone plugs

QC/T 400-2013 卡套式锥螺纹直角三通接头体

本标准规定了卡套式锥螺纹直角三通接头体的型式与尺寸、技术条件。本标准适用于管子外径为4mm~35mm,最大工作压力10MPa~25MPa的汽车用油、气及一般腐蚀介质的管路系统。

24° cone connectors.Male run tee.Body

QC/T 379-2013 方头锥形螺塞

本标准规定了方头锥形螺塞的型式与尺寸、技术条件。本标准适用于螺纹规格为NPT1/8~NPT2的汽车用方头锥形螺塞。

Square head cone plugs

SAE J846-2013 液体导体和连接器的识别用编码系统

This coding system is intended to provide a convenient means of identifying the various tube, pipe, hydraulic hose type and hose fittings, not intended for use in aircraft and of transmitting technical or engineering information relating to them wherever drawings or other pictorial media may not be readily available. The code has been kept flexible to permit expansion to cover new fitting categories or styles and, if the need develops, the inclusion of additional materials. The system is also compatible with automatic data processing equipment. It is not intended that this code should supersede established systems or means of identification. Therefore, it s

Coding Systems for Identification of Fluid Conductors and Connectors

SAE J1467-2013 封管机连接件

This SAE Standard covers material and dimensional requirements of steel clip fastener fittings. These fittings are intended for use in hydraulic systems on industrial equipment primarily in mining applications.

Clip Fastener Fitting

SAE J1401-2013 使用非石油基液压油的道路车辆液压制动软管总成

This SAE Standard specifies the performance tests and requirements for hydraulic brake hose assemblies used in the hydraulic braking system of a road vehicle. It also specifies the methods used for identification of the hose manufacturer. This document applies to brake hose assemblies made of a hose fabricated from yarn and natural or synthetic elastomers and assembled with metal end fittings for use with nonpetroleum-base brake fluids as specified in SAE J1703, SAE J1704 and SAE J1705. The nominal internal diameter of the brake hose shall be one of the following values: a. less than 4 mm (1/8 in) or, b. 4 to 5 mm (3/16 in).

Road Vehicle Hydraulic Brake Hose Assemblies for Use with Nonpetroleum-Base Hydraulic Fluids

SAE J517-2013 液压软管

This SAE Standard provides general, dimensional and performance specifications for the most common hoses used in hydraulic systems on mobile and stationary equipment. The general specifications contained in Sections 1 through 12 are applicable to all hydraulic hoses and supplement the detailed specifications for the 100R-series hoses contained in the later sections of this document. This document shall be utilized as a procurement document only to the extent as agreed upon by the manufacturer and user. The maximum working pressure of a hose assembly comprising SAE J517 hose and hose connectors per SAE J516, SAE J518, SAE J1453, etc., shall not exceed the lo

Hydraulic Hose

SAE J2996-2013 小直径燃料管道渗透试验规程

This SAE Recommended Practice is intended for the determination of the losses of hydrocarbon fluids by permeation through small diameter fuel hose typically 4.75mm ID or less and typically used on Small Off-Road Engines (SORE) less than 19 kW as regulated under 40 CFR Part 1054.

Small Diameter Fuel Line Permeation Test Procedure

SAE J1754-1-2013 21 MPa最大工作压力下液压橡胶软管组件的采购文件

This SAE Standard covers steel wire reinforced rubber hose assemblies using connectors specified in SAE J516 for use in hydraulic systems using petroleum based hydraulic fluids with maximum working pressures of 1.7 to 42 MPa. See Part 2, Table 7 for hose operating temperature ranges and identification codes.

Hose Assemblies, Rubber, Hydraulic, 21 MPa Maximum Working Pressure Procurement Document

SAE J2045-2012 燃料系统管道组件的性能要求

This SAE Standard encompasses the minimum requirements for non-metallic tubing and/or combinations of any metallic tubing to non-metallic tubing assemblies manufactured as a liquid- and/or vapor-carrying systems designed for use in gasoline, alcohol blends with gasoline, or diesel fuel systems. This SAE Standard is intended to cover tubing assemblies for any portion of a fuel system which operates above -40 degrees C (-40 degrees F) and below 115 degrees C (239 degrees F), and up to a maximum working gage pressure of 690 kPa (100 psi). The peak intermittent temperature is 115 degrees C (239 degrees F). For long-term continuous usage, the temperature shall n

Performance Requirements for Fuel System Tubing Assemblies

SAE J1610-2012 PVT试验性能的软管连接密封性能评价的试验方法

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This test method provides a standardized procedure for evaluating the sealing capability of a hose connection or any of the individual components of the connection with a pressure, vibration, and temperature (PVT) test facility. This test method consists of a test procedure which includes vibration and coolant flow and a similar test procedure specified without vibration or coolant flow. Any test parameters, other than those

Test Method for Evaluating the Sealing Capability of Hose Connections with a PVT Test Facility

SAE J246-2012 球形和法兰式套筒(压缩)管配件

This SAE Standard covers complete general and dimensional specifications for tube fittings of the spherical and flanged sleeve compression types for use in the piping of air brake systems on automotive vehicles. The spherical sleeve compression type figures 1A to 5 and Tables 1 to 3 is intended for use with annealed copper alloy tubing per SAE J1149, Type 1. The flanged sleeve compression type figures 6A to 11 and Tables 4 to 6 is intended for use with nylon tubing per SAE J844. It is not intended to restrict or preclude other designs of a tube fitting for use with SAE J844, air brake tubing. Performance requirements for SAE J844 are covered in SAE J1131. S

Spherical and Flanged Sleeve (Compression) Tube Fittings

SAE J2050-2012 高温动力方向盘压力软管

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Standard covers two types of hose fabricated from textile reinforcement and synthetic rubber, assembled with end fittings for use in high-temperature automotive power steering applications as flexible connections within the temperature range of -40 to +150 degrees C (-40 to +302 degrees F) maximum and 10.3 MPa (1500 psi) maximum working pressure. These hoses are intended for use in applications where reduction in amplitude of pump pressure pulsations is required. Class A hose has a nominal OD of 19.84 mm (0.781 in). Class B hose is a lightweight hose with a nominal OD of 17.91 mm (0.705 in). This specification defines the minimum performance levels of a flexible connector in the hydraulic steering system to convey power steering fluid from the steering pump to the steering gear.

High-Temperature Power Steering Pressure Hose

SAE J1833-2012 液压制动软管装配组件热冲击试验

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Recommended Practice presents an accelerated test to verify the structural integrity of hydraulic brake hose and the hose-to-fitting seal. It is intended to simulate the effects of environmental aging and braking pressurization on brake hose assemblies. The test is a guide to assist hose designers and/or users in determining brake hose assembly performance characteristics under conditions of heat and pressure.

Hot Impulse Test for Hydraulic Brake Hose Assemblies (Stabilized Type)