T38 照明与信号设备 标准查询与下载

JIS D 5711:2004 机动车用红色闪光信号灯

この規格は，自動車の使用時に，非常信号用具として用いる緊急保安炎筒(以下，保安炎筒という。)について規定する。

Red Fusee for Motor Vehicles

DLA MS51318 REV B VALID NOTICE 2-2004 24伏防水灯火管制前灯

MS51318B remains inactive for new design, however, the document is valid for use.

HEADLIGHT, BLACKOUT, 24-VOLT WATERPROOF

DLA MS51303 REV B VALID NOTICE 3-2004 清除黑色标记灯

The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil.

LIGHT, MARKER, CLEARANCE-BLACK

IEC 60809:2004 道路车辆用灯.尺寸、电及光的要求

This International Standard is applicable to replaceable lamps (filament lamps and discharge lamps) to be used in headlamps, fog-lamps and signalling lamps for road vehicles. It is especially applicable to those lamps which are the subject of legislation. In particular, it includes the lamps contained in Regulationsl) No.37 and No.99 of the Geneva Agreement of 20 March 1958 of the United Nations Economic Commission for Europe (ECE). However, the standard may be used for other lamps falling under the scope of this standard. The standard specifies the technical requirements with methods of tests and basic interchangeability (dimensional, electrical and luminous) for lamps of normal production and for standard (étalon) lamps. For most of the requirements given in this standard reference is made to the "relevant data sheet". For all lamps listed in Clause 5 , data sheets are contained in this standard. For other lamps the relevant data are supplied by the lamp manufacturer or responsible vendor. It could be based on national legislation. Other requirements such as lamp life, lumen maintenance, torsion strength and resistance to vibration and shock are specified in IEC 60810. The latter standard also gives information for guidance of lighting equipment design, such as temperature limits and maximum lamp outlines. Road vehicle lamps for supplementary purposes which are not the subject of legislation are specified in IEC 60983. In countries which legislate for approval, for example under the terms of the aforementioned ECE Regulations, it is suggested that reference is made to this standard for assessment of compliance. IEC 60810 and IEC 60983 are not intended for that purpose.

Lamps for road vehicles - Dimensional, electrical and luminous requirements

NF R13-630:2003 道路车辆灯.性能要求

Lamps for road vehicles - Performance requirements.

BS EN 60810:2003 道路车辆用灯.性能要求

This International Standard is applicable to replaceable lamps (filament lamps and discharge lamps) to be used in headlamps, fog-lamps and signalling lamps for road vehicles. It is especially applicable to those lamps which are listed in IEC 60809. However, the standard may also be used for other lamps falling under the scope of this standard, as well as for future developments, e.g. such where the light is produced by light emitting diodes (LED). It specifies requirements and test methods for the measurement of performance charac-teristics such as lamp life, lumen maintenance, torsion strength, glass bulb strength and resistance to vibration and shock. Moreover, information on temperature limits, maximum lamp outlines and maximum tolerable voltage surges is given for the guidance of lighting and electrical equipment design. For some of the requirements given in this standard, reference is made to data given in tables. For lamps not listed in such tables, the relevant data are supplied by the lamp manufacturer or responsible vendor. The performance requirements are additional to the basic requirements specified in IEC 60809. They are, however, not intended to be used by authorities for legal type-approval purposes. NOTE In the various vocabularies and standards, different terms are used for "incandescent lamp" (IEV 845-07-04) and "discharge lamp" (IEV 845-07-17). In this standard, "filament lamp" and "discharge lamp" are used. However, where only "lamp" is written both types are meant, unless the context clearly shows that it applies to one type only.

Lamps for road vehicles - Performance requirements

BS EN 60810:2003+A2:2013 道路车辆用灯具. 性能要求

Lamps for road vehicles - Performance requirements

SAE J587-2003 牌照照明设备(后牌照照明设备)

This SAE Standard provides test procedures, requirements, and guidelines for vehicular license plate illumination devices.

License Plate Illumination Devices (Rear Registration Plate Illumination Devices)

DLA A-A-59349 VALID NOTICE 1-2003 装有支架的反光镜

A-A-59349, dated 9 October 1998, has been reviewed and determined to be valid for use in acquisition

REFLECTORS, LIGHT; WITH HOLDER

SAE J2400-2003 前向碰撞预警系统的人为因素:工作特性和用户界面的要求

Forward Collision Warning (FCW) systems are onboard systems intended to provide alerts to assist drivers in avoiding striking the rear end of another moving or stationary motorized vehicle. This SAE Information Report describes elements for a FCW operator interface, as well as requirements and test methods for systems capable of warning drivers of rear-end collisions. This information report applies to original equipment and aftermarket FCW systems for passenger vehicles including cars, light trucks, and vans. This report does not apply to heavy trucks. Furthermore, this document does not address integration issues associated with adaptive cruise control (ACC), and consequently, aspects of the document could be inappropriate for an ACC system integrated with a FCW system.

Human Factors in Forward Collision Warning Systems: Operating Characteristics and User Interface Requirements

ISO 303:2002/cor 1:2003 道路车辆.汽车及其挂车的照明和光信号装置的安装.技术勘误1

This is Technical Corrigendum 1 to ISO 303-2001 (Road vehicles — Installation of lighting and light signalling devices for motor vehicles and their trailers )

Road vehicles - Installation of lighting and light signalling devices for motor vehicles and their trailers; Technical Corrigendum 1

IEC 60810:2003 道路车辆用灯.性能要求

This International Standard is applicable to replaceable lamps (filament lamps and discharge lamps) to be used in headlamps, fog-lamps and signalling lamps for road vehicles. It is especially applicable to those lamps which are listed in IEC 60809. However, the standard may also be used for other lamps falling under the scope of this standard, as well as for future developments, e.g. such where the light is produced by light emitting diodes (LED). It specifies requirements and test methods for the measurement of performance charac-teristics such as lamp life, lumen maintenance, torsion strength, glass bulb strength and resistance to vibration and shock. Moreover, information on temperature limits, maximum lamp outlines and maximum tolerable voltage surges is given for the guidance of lighting and electrical equipment design. For some of the requirements given in this standard, reference is made to data given in tables. For lamps not listed in such tables, the relevant data are supplied by the lamp manufacturer or responsible vendor. The performance requirements are additional to the basic requirements specified in IEC 60809. They are, however, not intended to be used by authorities for legal type-approval purposes. NOTE In the various vocabularies and standards, different terms are used for "incandescent lamp" (IEV 845-07-04) and "discharge lamp" (IEV 845-07-17). In this standard, "filament lamp" and "discharge lamp" are used. However, where only "lamp* is written both types are meant, unless the context clearly shows that it applies to one type only.

Lamps for road vehicles - Performance requirements

SAE HS-34-2003 地面车辆照明标准手册,不包括图像,请参阅完整版

Ground Vehicle Lighting Standards Manual IMAGES ARE NOT INCLUDED; PLEASE REFER TO GLOBAL;

Ground Vehicle Lighting Standards Manual IMAGES ARE NOT INCLUDED; PLEASE REFER TO GLOBAL

SANS 20099:2002 用于已通过认证的机动车的气体放电灯具的气体放电光源认证的统一规定

Applies to gas-discharge light sources intended for use in approved gas-discharge lamp units of power-driven vehicles.

Uniform provisions concerning the approval of gas-discharge light sources for use in approved gas-discharge lamp units of power-driven vehicles

NF R13-629/A2:2002 道路车辆用照明灯.尺寸、电气和照明要求

Lamps for road vehicles - Dimensional, electrical and luminous requirements.

DLA MS53047 REV A (1)-2002 24 V服务信号和停电标记服务区灯

This amendment forms a part of MS53047A dated 21 February 1994 and is approved for use by all Departments and Agencies of the Department of Defense.

LIGHT, MARKER-SERVICE PARK, SERVICE SIGNAL AND BLACKOUT, 24 VOLT

DLA MS35423 REV B (1)-2002 结关服务指示灯

This amendment forms a part of MS35423B dated 18 September 1987 and is approved for use by all Departments and Agencies of the Department of Defense.

LIGHT, MARKER, CLEARANCE-SERVICE

IEC 60809:2002 道路车辆灯.尺寸,电气和亮度要求

Covers filament lamps to be used in headlamps, fog-lamps and signalling lamps for road vehicles and specifies the technical requirements with methods of test and basic interchangeability (dimensional, electrical and luminous). It applies to those filamen

Lamps for road vehicles - Dimensional, electrical and luminous requirements

SAE J974-2002 农业设备用闪光警报灯

This SAE Standard covers the general requirements and the test requirements for a flashing warning lamp for agricultural equipment.

Flashing Warning Lamp for Agricultural Equipment

DLA MS25219 REV G (1)-2002 飞行器航空和警告灯

This amendment forms a part of MS25219G dated 5 March 1993 and is approved for use by all Departments and Agencies of the Department of Defense.

LIGHT - NAVIGATIONAL AND WARNING, AIRCRAFT