T38 照明与信号设备 标准查询与下载

SAE J2040-2002 总体宽度在2032mm和以上的车辆用尾灯(后位置尾灯)

This SAE Standard provides test procedures, requirements, and guidelines for tail lamps intended for use on vehicles 2032 mm or more in overall width. Tail lamps conforming to the requirements of this document may also be used on vehicles less than 2032 mm in overall width. Tail lamps conforming to the requirements of this document may also be used on vehicles less than 2032 mm in overall width.

Tail Lamps (Rear Position Lamps) for Use on Vehicles 2032 mm or More in Overall Width

IEC 60810:2002 道路车辆灯.性能要求

Lamps for road vehicles - Performance requirements

SAE J2261-2002 总体宽度等于或大于2032mm的机动车辆用停止灯和前后转弯信号灯

This SAE Standard provides test procedures, requirements, and guidelines for stop lamps and turn signal lamps intended for use on vehicles 2032 mm or more in overall width. Stop lamps and front- and rear-turn signal lamps conforming to the requirements of this document may be used on vehicles less than 2032 mm in overall width.

Stop Lamps and Front- and Rear-Turn Signal Lamps for Use on Motor Vehicles 2032 mm or More in Overall Width

SANS 20057:1995 关于批准摩托车以及类似车辆前照灯的统一规定

Applies to the approval of headlamps using filament lamps and incorporating lenses of glass or plastic material, which are provided for the equipment of motor cycles and vehicles treated as such.

Uniform provisions concerning the approval of headlamps for motor cycles and vehicles treated as such

IEC 60810/AMD2:2001 道路机动车辆用灯 性能要求 修改2

Lamps for road vehicles - Performance requirements; Amendment 2

SANS 20086:1993 农林拖拉机灯光和信号装置的安装认证的统一规定

Applies to the approval of agricultural or forestry tractors with regard to the installation of lighting and light-signalling devices. Applies only to agricultural or forestry tractors which are fitted with pneumatic tyres and which have at least two axl

Uniform provisions concerning the approval of agricultural or forestry tractors with regard to the installation of lighting and light-signalling devices

DLA MS51302 REV B VALID NOTICE 2-2001 24伏车载灯火管制红色尾灯

MS51302B remains inactive for new design, however, the document is valid for use.

STOPLIGHT, VEHICULAR-BLACKOUT, 24 VOLT

SAE J2039-2001 大型车辆用的转弯单个灯

This SAE Recommended Practice provides test procedures, requirements, and guidelines for side turn signal lamps intended for use on trailers 12 m or more in overall length except pole trailers. Side turn signal lamps conforming to the requirements of this document may be used on other large vehicles such as trucks, truck tractors, buses, and other applications where this type of lighting device is desirable.

Side Turn Signal Lamps for Large Vehicles

SAE J583-2001 前雾灯

This SAE Standard provides performance requirements, test procedures, and design and installation guidelines for front fog lamps. The front fog lamp is designed to be used in adverse weather conditions.

Front Fog Lamps

SAE J852-2001 用于机动车辆的前拐弯灯

This SAE Recommended Practice provides test procedures, performance requirements, and guidelines for front cornering lamps intended for use on motor vehicles.

Front Cornering Lamps for Use on Motor Vehicles

ISO 2575:2000/Amd 1:2001 道路车辆 操纵件、指示器和信号装置的符号 修改1

Road vehicles - Symbols for controls, indicators and tell-tales; Amendment 1

ISO 2575:2000/Cor 1:2001 道路车辆 操纵件、指示器和信号装置的符号 技术勘误1

Road vehicles - Symbols for controls, indicators and tell-tales; Technical Corrigendum 1

SANS 20056:1989 与轻便摩托车及类似车辆的前照灯的批准有关的统一规定

Applies to the approval of headlamps using filament lamps, producing one single passing beam, which are provided for the equipment of mopeds and vehicles treated as such.

Uniform provisions concerning the approval of headlamps for mopeds and vehicles treated as such

SAE J585-2000 总体宽度小于2032mm的机动车辆的尾灯使用(后位灯)

This SAE Standard provides test procedures, requirements, and guidelines for tail lamps (rear position lamps).

Tail Lamps (Rear Position Lamps) for Use on Motor Vehicles Less Than 2032 mm in Overall Width

SAE J588-2000 总体宽度小于2032mm的机动车辆的转向信号灯使用

This SAE Standard provides test procedures, requirements, and guidelines for turn signal lamps intended for use on vehicles of less than 2032 mm in overall width.

Turn Signal Lamps for Use on Motor Vehicles Less Than 2032 mm in Overall Width

SAE J593-2000 倒车灯

This SAE Standard provides installation requirements, test procedures, design guidelines and performance requirements for backup lamps.

Backup Lamps (Reversing Lamps)

SAE J1432-2000 总体宽度等于或超过2032mm的车辆中使用的高安装的停止灯

This SAE Information Report provides test procedures, requirements, and guidelines for high-mounted stop lamps intended for use on vehicles 2032 mm or more in overall width. This document applies to trucks, motor coaches, van type trailers, and other vehicles with permanent structure greater than 2.8 m high. This document does not apply to school buses, truck tractors, pole trailers, flat-bed trailers, and trailer converter dollies. The purpose of the high-mounted stop lamp or lamps is to provide a signal over intervening vehicles to the driver of following vehicles.

High-Mounted Stop Lamps for Use on Vehicles 2032 mm or More in Overall Width

SAE J1957-2000 总体宽度小于2032mm的中央高固定停止灯的标准

This SAE Standard provides test procedures, requirements, and guidelines for center high mounted stop lamps (CHMSL) for use on vehicles less than 2032 mm in overall width.

Central High Mounted Stop Lamp Standard for Vehicles Less than 2032 mm Overall Width

SAE J586-2000 总体宽度小于2032mm的机动车辆的停车灯使用

This SAE Standard provides test procedures, requirements, and guidelines for stop lamps intended for use on vehicles of less than 2032 mm in overall width.

Stop Lamps for Use on Motor Vehicles Less Than 2032 mm in Overall Width

SAE J222-2000 停车灯(前位灯)

This SAE Standard provides test procedures, requirements, and guidelines for parking lamps (front position lamps).

Parking Lamps (Front Position Lamps)