T42 客车 标准查询与下载

GM 9986124-1996 水基润滑干膜

Slatvavd polyester Polyamid laminerad Polyester Polyamid flat woven fabric laminated

Lubricant - Dry Film, Water Based

GM 9985992-1995 双层包覆腈纶泡沫磁带胶粘剂

Denna standard overensstammer med Opel materialspecifikation enligt foljande

Adhesive, Foam Tape, Acrylic, Double Coated

GM 9984511-1995 9984858的清漆成分

Deviations from the requirements specified in this material specification or additional requirements shall have been agreed upon. These shall be indicated in the respective engineering drawing, material release and or terms of delivery.

Clearcoat Component of 9984858

GM 9984858-1995 韧性瓷漆,溶剂型清漆/水性底漆,面漆系统

In diesen Technischen Lieferbedingungen sind die qualitatsabhangigen Anforderungen dieses Polsterstoffes festgelegt. Die allgemeinen Mindestanforderungen sind grundsatzlich nach TM 110000 zu prüfen.

Topcoat - Flexible Enamel, Waterborne Basecoat/Solvent- Borne Clearcoat Revision A

JIS D 1061:1995 小客车转向控制系统实验室冲击试验程序

この規格は，乗用車のステアリングコントロールシステム(以下，ステアリングという。)の人体に対する衝撃特性を評価するためのボアープロックを用いた試験室内での試験方法について規定する。

Steering control system laboratory impact test procedure for passenger cars

GOST R 50844-1995 运输病人用客车.一般技术要求

Настоящий стандарт распространяется на автобусы, специально предназначенные для перевозок инвалидов с нарушениями опорно-двигательных

Buses for carrying invalids. General requirements

JT 94-1994 客车质量检查评定方法

本标准规定了客车质量检车的检查项目、抽样规定、评定标准、检查方法、评定规则及检查结果处理等。 本标准作为客车产品质量检查、质量监督抽查及质量分等依据。 本标准适用于车辆长大于3.5m的大型、中型、轻型客车，特大型客车参照执行。

Inspecting and evaluating method for quality of buses

GM 9985994-1994 手动变速器液

Unbeschodct etwaiger durch den Abnehmer erfolgenden Stichprabenprüfungen tragt der Lieferant die Verantwortung dafür, dai3 die gelieferle Wore die Opel -Zeichnungsvorschriften erfüllt. Mustern sowie Teilen einer ersten Serienlieferung ist unaufgefordert e

Fluid, Manual Transmission

BS AU 256:1994 乘用车.车辆转向电源开断的反应.开环试验法

This International Standard defines an open-loop test method for determining the power-off reactions of a vehicle in a turn. It applies to passenger cars as de-fined in ISO 3833. It is not possible at present to use this procedure and test results for regulation purposes.

Passenger cars - Power-off reactions of a vehicle in a turn - Open-loop test method

GM 9985985-1994 树脂环氧树脂为两部分胶粘剂

8655-2 Bagagerumsgolv 8655-2 Luggage compartment floor

Adhesive, Two-Part, Epoxy, Resin

GM 9985602-1994 树脂环氧树脂分为两个部分粘合剂

impact strength also at low temperatures, e.g. trim - wheelhouse. Spritzgießtype zur Herstellung technischer Teile mit hoher Schlagzahigkeit auch in der Kalte, z.B.

Adhesive, Two-Part, Epoxy, Resin Revision C

GM 9985954-1994 树脂丙烯酸酯为两部分胶粘剂

PA6.6 med goda lagtemperaturegenskaper. Avsedd for formsprutning.

Adhesive, Two-Part, Acrylic, Resin

GM 9985984-1994 室温固化紫外线设定环氧树脂为两部分胶粘剂

Materialet ar avsett for formsprutning och har god vaderbestandighet i kombination med hog slagseghet temperaturtalighet.

Adhesive, Two-Part, Epoxy, UV Set, Room Temperature Cure

DIN ISO 8667:1993 商用车辆和大客车.T型十字齿齿轮箱法兰

Commercial vehicles and buses; cross-tooth gearbox flanges, type T; identical with ISO 8667:1992

SAE J1863-1993 铁路客车接缝断裂试验

This SAE Recommended Practice defines a procedure for determining the cleavage strength of anadhesive used for bonding automotive oily metal substrates.

Coach Joint Fracture Test

DIN ISO 2416:1993 搭乘车.质量分布

For passenger cars, the load distribution for the transportable weights is given.#,,#

Passenger cars; mass distribution; identical with ISO 2416:1992

ISO 7397-2:1993 乘用车 驾驶员直接视野的验证 第2部分:试验方法

Specifies a test method for verifying the compliance of a passenger car (as defined in ISO 3833) with the requirements of EEC Directives 77/649 and 88/366 for the driver's 180?forward field of view.

Passenger cars; verification of driver's direct field of view; part 2: test method

ISO 7397-1:1993 乘用车 驾驶员直接视野的验证 第1部分:车辆静态测量定位

Establishes the initial procedure for positioning of a passenger car relative to a three-dimensional reference system, as given in ISO 4130, for the purposes of static measurements on the vehicle. It enables verification of the driver's forward 180?field of view, however, the procedure shown may also be followed for checking other aspects of vehicle design.

Passenger cars; verification of driver's direct field of view; part 1: vehicle positioning for static measurement

CJ/T 3004-1993 轿车、微型客车及小型客车修理技术条件

Technical specifications for cars,micro-vans and mini-vans being overhauled

CJ/T 3003-1993 出租汽车运行技术条件

本标准规定了出租汽车运行应具备的技术条件。 本标准适用于所有出租汽车。

The technical specifications for taxi service vehicle