T85 电子、电气设备 标准查询与下载

ISO 11460:2007 两轮摩托车.照明和光信号装置的定位

This International Standard specifies the requirements for the positioning of lighting and light-signalling devices when fitted to a two-wheeled motorcycle as defined in ISO 3833. It does not specify the installation of any of these devices.

Two-wheeled motorcycles - Positioning of lighting and light-signalling devices

QC/T 738-2005 轻便摩托车用电喇叭技术条件

本标准规定了用于L和L类的轻便摩托车用电喇叭的要求、试验方法、检验规则和标志、包装、运输及贮存。 本标准适用于L和L的轻便摩托车用直流或交流供电的电喇叭。

Specifications of electronic horn for motorcycles and mopeds

SANS 20075:2004 摩托车和轻便摩托车气压轮胎的认证的统一规定

Covers new pneumatic tyres designed primarily, but not only, for vehicles in categories L1, L2, L3 and L4. Does not apply to tyre types designed exclusively for the "off road" use, which are marked "NHS" (Not for Highway Service) and to tyre types design

Uniform provisions concerning the approval of pneumatic tyres for motor cycles and mopeds

QC/T 724-2004 摩托车和轻便摩托车直流信号闪光器技术条件

本标准规定了摩托车和轻便摩托车直流信号闪光器的技术要求、试验条件和方法、检验规则及标志、包装、运输。 　　本标准适用于摩托车和轻便摩托车用直流型号闪光器。

Specification for direct current flasher units of motorcycles and mopeds

ISO 10355:2004 轻便摩托车.照明和光信号装置的定位

This International Standard specifies the requirements for the positioning of lighting and light-signalling devices when fitted to a moped, as defined in ISO 3833. It does not specify the installation of any of these devices.

Mopeds - Positioning of lighting and light-signalling devices

QC/T 680-2002 摩托车和轻便摩托车用电压调节器技术条件

本标准规定了摩托车和轻便摩托车用电压调节器的技术要求、试验方法、检验规则和标志、包装、运输及贮存。 　　本标准适用于摩托车和轻便摩托车用调节器。

Specifications for voltage regulators for motorcycles and mopeds

QC/T 681-2002 摩托车和轻便摩托车用起动继电器技术条件

本标准规定了摩托车和轻便摩托车用起动继电器的技术要求、试验方法、检验规则和标志、包装、运输及贮存。 　　本标准适用于摩托车和轻便摩托车用继电器。

Specifications for starter relays for motorcycles and mopeds

SANS 20074:2000 轻便摩托车灯光和光信号装置的认证的统一规定

Applies to the approval of two-wheeled power-driven vehicles without side-car, having a maximum design speed not exceeding 50 km/h and/or a cylinder capacity not exceeding 50 cubic centimetres or equivalent performance.

Uniform provisions concerning the approval of category L1 vehicles with regard to the installation of lighting and light-signalling devices

SANS 20072:1988 发射非对称近光和远光并装有卤素灯（HIS灯）的摩托车前大灯的认证的统一规定

Applies to the approval of headlamps equipped with halogen filament lamps (HS1 lamps), which are provided for the equipment of motor cycles and vehicles treated as such.

Uniform provisions concerning the approval of motor cycle headlamps emitting an asymmetrical passing beam and a driving beam and equipped with halogen filament lamps (HS1)

SANS 20076:1988 发射远光和近光的轻便摩托车前照灯的认证的统一规定

Applies to the approval of headlamps using filament lamps, producing a driving beam and a passing beam, which are provided for the equipment of mopeds and vehicles treated as such.

Uniform provisions concerning the approval of headlamps for mopeds emitting a driving beam and a passing beam

SANS 20082:1989 装有白炽卤素灯（HS2）的轻便摩托车前照灯的认证的统一规

Applies to the approval of headlamps equipped with halogen lamps (HS2 lamps), which are provided for the equipment of mopeds and vehicles treated as such.

Uniform provisions concerning the approval of moped headlamps equipped with filament halogen lamps (HS2 lamps)

SAE J1167-1998 摩托车停车灯开关

This SAE Recommended Practice establishes test procedures and performance requirements for stop lamp switches intended for use in an AC or a DC circuit on motorcycles. In service use may impose specific conditions on the switch which can affect its functional life. Those conditions should be replicated, as necessary, during the testing described in this document to ensure the adequate functioning of the device.

Motorcycle Stop Lamp Switch

NF R29-010:1997 操作规程指南.摩托车用电子锁

Practical guide. Electronic locks for motorcycles.

QC/T 29117.14.1-1993 摩托车和轻便摩托车产品质量检验 磁感应式车速里程表质量评定方法

Method for quality assessment of magnetic induction speedometer for product quality inspection of motorcycles and mopeds

QC/T 29117.17.1-1993 摩托车和轻便摩托车产品质量检验 发动机磁电机质量评定方法

Motorcycle and moped product quality inspection method for quality assessment of engine magneto

QC/T 29117.17.2-1993 摩托车发动机用磁电机可靠性评定方法

Reliability Evaluation Method of Magneto Used in Motorcycle Engine

QC/T 29117.18.1-1993 摩托车和轻便摩托产品质量检验 发动机永磁交流发电机质量评定方法

Motorcycles and mopeds product quality inspection engine permanent magnet alternator quality assessment method

QC/T 29117.18.2-1993 摩托车和轻便摩托车产品质量检验 发动机永磁交流发电机可靠性评定方法

Motorcycle and moped product quality inspection engine permanent magnet alternator reliability assessment method

QC/T 29117.14.2-1993 摩托车和轻便摩托车产品质量检验 磁感应式转速表质量评定方法

Method for quality assessment of magnetic induction tachometers for product quality inspection of motorcycles and mopeds

QC/T 67-1993 摩托车喇叭声级测量方法

本标准规定了摩托车和轻便摩托车喇叭声级的测量条件和测量方法。 　　本标准适用于装在摩托车和轻便摩托车上的电喇叭声级测量。

Measurement method of motorcycle horn sound level