U57 船用液压、气动元件及附件 标准查询与下载

CB/T 3823-2013 船用液控单向阀

本标准规定了船用液控单向阀(以下简称单向阀)的分类、要求、试验方法、检验规则及标志、包装、运输和贮存。本标准适用于以石油基液压油为工作介质的船用单向阀的设计、制造和检验。其他行业用的单向阀的设计、制造和检验可参照使用。

Hydraulic pilot controlled check valve for ship

SAE J1939/74-2010 应用程序配置消息

The SAE J1939 documents are intended for light, medium, and heavy-duty vehicles used on or off road as well as appropriate stationary applications which use vehicle derived components (e.g. generator sets). Vehicles of interest include, but are not limited to, on- and off-highway trucks and their trailers, construction equipment, and agricultural equipment and implements. The purpose of these documents is to provide an open interconnect system for electronic systems. It is the intention of these documents to allow Electronic Control Units to communicate with each other by providing a standard architecture. This particular document, SAE J1939-74, describes the message structure for a set of messages which enable the user to determine and announce to others on the network, the parameter placement within a particular message from the special set of messages defined within this document.

Application Configurable Messaging

CB 1388-2008 舰船用液压泵、马达规范

本规范规定了舰船用叶片式、齿轮式、轴向柱塞式液压泵、马达（以下简称泵、马达）的要求、质量保证规定和交货准备。 本规范适用于工作介质为石油基液压油的泵、马达的研制、生产和验收。 本规范不适用于低速大扭钜马达。

Specification for hydraulic pump and motor of ships

CB/T 1102-2008 船用液压系统通用技术条件

本标准规定了船用液压系统的要求、元件与辅件的应用、配管和清洗等。 本标准适用于船舶机械设备的液压传动和控制系统、包括全船的配套设备的液压系统的设计和制造。

General specification for hydraulic system of ship

CB 1399-2008 舰船用低噪声液压泵规范

本规范规定了舰船用轴向柱塞式、子母叶片式、柱销叶片式和内啮合齿轮式低噪声液压吵泵（以下简称泵）的要求、质量保证规定和交货准备等。 本规范适用于以石油基矿物为工作介质的泵的设计、制造和验收。

Specification of low noise hydraulic pump for ship

CB 1389-2008 舰船用液压泵站规范

本标准规定了舰船用液压泵站（以下简称泵站）的要求、质量保证规定和交货准备等。 本规范适用于以石油基液压油为工作介质的泵站的研制、生产及验收。

Specification for hydraulic fluid power units of ships

SAE J2321-2-2006 船用系统和设备一次性液压过滤元件.190升/分流量、21MPa破裂压力、在7um时过滤比率为75

This specification sheet establishes requirements for a high collapse pressure configuration filter element of a specific configuration with a minimum filtration ratio of 75 for particles larger than 7 ?m when designed and tested in accordance with SAE J2321 and this specification sheet.

Ship Systems and Equipment Disposable Hydraulic Filter Element 190 L/Min Flow, 21 MPa Collapse Pressure, Filtration Ratio = 75 at 7 ?m

SAE J2321/3-2006 船舶系统和设备一次性液压滤波器元件.75-175L/Mi、21 MPa破裂压力、在10μｍ时过滤比率为75

This specification sheet establishes requirements for high collapse pressure configuration filter elements of several configurations with a minimum filtration ratio of 75 for particles larger than 10 ?m when designed and tested in accordance with SAE J 2321 and this specification sheet.

Ship Systems and Equipment Disposable Hydraulic Filter Elements 21 MPa Collapse Pressure, Filtration Ratio = 75 at 10 ?m, 75 to 175 L/Min

SAE J2321-1-2006 船用系统和设备一次性液压过滤元件.115升/分流量、1000MPa破裂压力、在6和10um时过滤比率为75

This specification sheet establishes requirements for low collapse pressure elements of a specific configuration with various efficiency ratings designed and test in accordance with SAE J2321 and the requirements for this specification sheet.

Ship Systems and Equipment Disposable Hydraulic Filter Element 115 L/Min Flow, 1.000 MPa Collapse Pressure, Filtration Ratio = 75 at 6 and 10 ?m

CB 1375-2005 登陆舰艉部液压泵站规范

本规范规定了登陆舰艉部液压泵站（以下简称液压泵站）的要求、质量保证规定和交货准备等。 本规范适用于公称压力为20MPa，油液温度不高于65℃的液压泵站的设计、制造和验收。

Specification for stern hydraulic power pack of landing ship

CB/T 3004-2005 船用往复式液压缸基本参数

本标准规定了船用往复式液压缸（以下简称液压缸）的公称压力、液压缸内径、柱塞直径、活塞杆外径、面积比、行程和油口公称基本参数通径等基本参数。 本标准适用于液压缸的设计与制造。

Basic parameter of reciprocation hydraulic cylinder for ship

CB/T 3600-2005 船用平衡阀

本标准规定了船用外控型平衡阀（以下简称平衡阀）的分类、要求、试验方法、检验规则、标志和包装。 本标准适用于以液压油为介质的平衡阀的设计、制造和验收。

Marine counterbalance valve

CB 688-2005 舰船用手动液压滑阀操纵器规范

本规范规定了船舰用手动液压滑阀操纵器（以下简称操纵器）的要求、质量保证规定和交货准备等。 本规范适用于公称压力为10MPa的操纵器的设计、制造和验收。

Specification for handle hydraulic spool controller of ship

CB 1377-2005 登陆舰艉部液压控制系统规范

本规范规定了登陆舰液压艉锚机控制系统和液压艉门控制系统（以下统称控制系统）的要求、质量保证规定和交货准备等。 本规范适用于控制系统的设计、制造和验收。

Specification for stern hydraulic control system of landing ship

CB/T 1123-2005 轴流涡轮液力变矩器 基本参数

本标准规定了轴流涡轮液力变矩器 （以下简称变矩器 ）的术语和定义、基本参数及标记。 本标准适用于抓斗式挖泥船和工程船的起吊机构以及轨道吊车、挖掘机、起重机械等用变矩器的设计和计算。

Axial turbine hydrodynamic torque converter--Basic parameters

KS V 6731-2005 船舶用液压舵机的油泵工厂试验方法

이 규격은 유압 조타기에 사용하는 유압 펌프(이하 펌프라 한다.)의 공장 시험 방법에 대하

Shop test mehod for oil pressure pumps at hydraulic steering gears for ships

GJB 5374-2005 舰船用液压囊式蓄能器规范

本规范规定了舰船用液压囊式蓄能器（以下简称蓄能器）的要求、质量保证规定及交货准备。 本规范适用于舰船用蓄能器的设计、制造、试验及验收。

Specification for bladder type hydraulic accumulators of ships

SAE J2333-2004 船舶系统和设备液压系统过滤器选择参数

This SAE Recommended Practice identifies and examines the various parameters which must be considered in selecting hydraulic systems filters, their locations within the system and the dirt capacity of the filter elements. This document is generally applicable to all ship hydraulic systems but does not apply to personal or recreational watercraft.

Ship Systems and Equipment Hydraulic Systems Filter Selection Parameters

CB 1374-2004 舰船用往复式液压缸规范

Specification of reciprocating hydraulic cylinder for naval ship

KS V 6730-2003 船舶用液压舵机工厂试验方法

이 규격은 KS V 6731의 적용 범위에 나타낸 펌프를 갖춘 유압 조타기의 공장 시험

Shop test method for ships’ hydraulic steering gears