共找到 2302 条与 管件、卡箍、密封件 相关的标准,共 154 页
Aerospace series - Clamps, loop ("P" type) in aluminium alloy, with rubber cushioning - Dimensions, masses; German and English version EN 4114:2009
Aerospace series - Clamps, loop ("P" type) in corrosion resisting steel, passivated, with rubber cushioning - Dimensions, masses; German and English version EN 4113:2009
FITTING, UNION AND REDUCER, FLARELESS, PRECISION TYPE
Aerospace series - Clamps, saddle fixed and sliding version in aluminium alloy with rubber cushioning - Dimension, masses; German and English version EN 3730:2009
Aerospace series - Pipe coupling 8°30' in titanium alloy - Elbows 90°, welded end with thrust wire nut; German and English version EN 4020:2009
This specification covers one grade of commercially-pure titanium in the form of seamless tubing. This tubing has been used typically for parts, such as fluid-conducting lines, requiring strength up to 400 °F (205 °C) and oxidation resistance up to 600 °F (315 °C), but usage is not limited to such applications.
Titanium Tubing, Seamless Annealed, 40.0 ksi (275 MPa) Yield Strength (UNS R50400)
Flange End, Male, Type II, Low Profile, Design Standard
Flange End, Male, Type I, Standard Profile, Design Standard
This specification covers a titanium alloy in the form of seamless tubing. This tubing has been used typically for parts, such as high-pressure hydraulic lines, requiring high strength and oxidation resistance up to 550 °F (288 °C) and weldability, but usage is not limited to such applications.
Titanium Alloy, Seamless Hydraulic Tubing, 15V 3.0Cr 3.0Al 3.0Sn Cold Worked and Precipitation Heat Treated
Flange End, Female, Type I, Standard Profile, Design Standard
No scope available.
FITTING, ELBOW, 90 DEGREES, STANDARD AND REDUCER, FLARELESS
FITTING, CONNECTOR, MULTIPLE FLUID PRESSURE LINE, 90 DEGREES
This SAE Aerospace Standard (AS) describes cleaning methods for four cleanliness levels of polytetrafluoroethylene hose assemblies and rigid tube assemblies for use in aerospace systems.
Hose Assembly and Tubing, Polytetrafluoroethylene, Cleaning Methods for
This document specifies the characteristics of elbows 45Ф, swivel nut, welded, in titanium alloy intended for use in aircraft fluid system pipelines.
Aerospace series - Pipe coupling 8°30' in titanium alloy - Elbows 45° welded end with thrust wire nut; German and English version EN 4024:2009
This standard specifies the characteristics of bearings, spherical plain with self lubricating liner in corrosion resisting steel with self-lubricating liner, wide series for aerospace applications.They are intended for use in fixed or moving parts of the aircraft structure and control mechanisms.They shall be used in the temperature range - 55 ФC to 163 ФC.
Aerospace series - Spherical plain bearings in corrosion resisting steel with self-lubricating liner, wide series - Dimensions and loads - Inch series; German and English version EN 4614:2009
This British Standard specifies procedures for the inspection, testing and acceptance of seamless steel tube and tubestock for aerospace use. The standard is applicable to material specifications in the British Standard Aerospace T series and also to other British Standard material specifications for seamless steel tubes and tubestock which are suitable for aerospace use.
Aerospace series - Procedure for inspection, testing and acceptance of seamless steel tubes and tubestock
Fitting, Union, Standard and Reducer, Bulkhead, Flared
Aerospace series - Pipe coupling 8 o30' in titanium alloy - Elbows 90 o with thrust wire nut.
Fitting, Nipple, Flared Tube to Pipe Thread, for Seal Ring
이 표준은 접지가 있거나 또는 없는, ISO 2964로부터 선정된 관 바깥지름이 4 mm
Aerospace-Fluid systems-Clamp blocks for tube lines having axial alignment-Design standard and qualification testing-Metric series
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号