共找到 171 条与 电气装置用结构件 相关的标准,共 12 页
This Commercial Item Description (CID) is approved by the Commissioner,Federal Supply Service, General Services Administration, for the use of all Federal agencies.
POLISHER, FLOOR, ELECTRIC, CONCENTRATED WEIGHT TWO-BRUSH (COMMERCIAL TYPE)
This Commercial Item Description (CID) is approved by the Commissioner, Federal Supply Service, General Services Administration, for the use of all Federal agencies.
POLISHER, FLOOR, ELECTRIC, CONCENTRATED WEIGHT SINGLE BRUSH (COMMERCIAL TYPE)
Acquisition activity should specify the following
POLISHER, FLOOR, ELECTRIC, DIVIDED WEIGHT (COMMERCIAL TYPE)
この規格は,地上電源から航空機に電カを供給するために使用する,次のコネクタの寸法について規定する。
Aircraft -- Connectors for ground electrical supplies -- Part 2: Dimensions
この規格は,地上電源から航空機に電力を供給するために使用する電気コネクタの設計,性能及び試験の諸要求事項を規定する。
Aircraft -- Connectors for ground electrical supplies -- Part 1: Design, performance and test requirements
This specification covers an irradiated, thermally-stabilized, modified polyolefin plastic in the form of semi-rigid, thin-wall, heat-shinkable tubing. This tubing has been used typically as a semi-rigid, electrical insulation tubing whose diameter can be reduced to a predetermined size by heating to 120 degrees C (250 degrees F) or higher, but usage is not limited to such applications.
Tubing, Irradiated Polyolefin Plastic, Electrical Insulation Clear, Semi-Rigid, Heat Shrinkable, 2 to 1 Shrink Ratio
This draft is now available for public comment and your views and technical comments on it would be appreciated. If you have no specific comments to make hut find it generally acceptable it would be helpful if you would notify US accordingly. Suggestions entailing revision of the text should indicate the preferred wording. Please quote the relevant clause number against any comment.
Aerospace Series Electrical Contacts Used in Elements of Connection Part 001 - Technical Specification Edition P 1
本标准主要规定了机载设备中系统图和框图、电路图、逻辑图、接线图和接线图和接线表、总布置图、系统说明书用简图电气图的编制方法,也规定了印制板图的编制方法,它是对GB6988和GB7356及GB5489的补充。 本标准适用于机载设备上述电气图的编制。
Aeronautical electrical drawing method for airborne equipment
This specification covers electric capstans for use on Naval ships.
CAPSTANS, ELECTRIC (FOR SHIPBOARD USE)
This specification covers hand-operated chain hoists.
HOISTS, CHAIN, HAND-OPERATED, HOOK AND TROLLEY SUSPENSION
MIL-C-22667B(SH) dated 11 May 1966, has been reviewed and determined to be valid for use in acquisition.
CABLE, SPECIAL PURPOSE, BUOYANT, ELECTRICAL, TYPE RG-298/U (SUBMARINE USE)
1.1 This aerospace specification establishes the requirements for metric loop or “P”style clamps used for systems installation in aerospace equipment.Product Classification:1.2 The clamp assemblies covered by this document all incorporate a single mounting point, but may be bare or cushioned an vary in shape such as fully round , partially round, or rectangular.1.3 Use of thes clamp assemblies is primarily for the support of fluid systems tubing and component, but may be used for other general purpose applications such as wire, cable ,wave guide tubes, system grounding, as determined applicable by the design activity. Installation and selection is recommended per ARP 1897.
CLAMP, LOOP STYLE, WITH INSERT, PHOSPHATE ESTER FLUID RESISTANT, METRIC
1.1 This aerospace specification establishes the requirements for metric loop or “P”style clamps used for systems installation in aerospace equipment.Product Classification:1.2 The clamp assemblies covered by this document all incorporate a single mounting point, but may be bare or cushioned an vary in shape such as fully round , partially round, or rectangular.1.3 Use of thes clamp assemblies is primarily for the support of fluid systems tubing and component, but may be used for other general purpose applications such as wire, cable ,wave guide tubes, system grounding, as determined applicable by the design activity. Installation and selection is recommended per ARP 1897.
CLAMP, LOOP STYLE, WITH INSERT, HIGH TEMPERATURE, METRIC
1.1 This aerospace specification establishes the requirements for metric loop or “P”style clamps used for systems installation in aerospace equipment.Product Classification:1.2 The clamp assemblies covered by this document all incorporate a single mounting point, but may be bare or cushioned an vary in shape such as fully round , partially round, or rectangular.1.3 Use of thes clamp assemblies is primarily for the support of fluid systems tubing and component, but may be used for other general purpose applications such as wire, cable ,wave guide tubes, system grounding, as determined applicable by the design activity. Installation and selection is recommended per ARP 1897.
CLAMP, LOOP STYLE, CUSHIONED, WITH WEDGE, PHOSPHATE ESTER FLUID RESISTANT, METRIC
This industrial standard for the aerospace sector has been drawn up under the responsibility of AECMA (Association Europhnne des Constructeurs de Matériel Aérospatial). It is published on yellow paper in three equivalent versions (English, French, German). It will be submitted to CEN (European Committee for Standardization) as a draft European Standard.
Aerospace Series Electrical Contacts Used in Elements of Connection Part 015 - Contacts, Electrical, Female 015, Type A, Crimp, Class S Product Standard Issue P 1
This draft is now available for public comment and your views and technical comments on it muld be appreciated. Ifyou have no specific comments to make but fmd it generally acceptable it muld be helpfu! if you mould notify us accordingly Suggestions entailing revision of the text should indicate the preferred wording. Please quote the relevant clause number against any comment.
Aerospace Series Electrical Contacts Used in Elements of Connection Part 014 - Contacts, Electrical, Male 014 Type A, Crimp, Class S Product Standard Issue P 1
The standard covers the technical specifications for circuit beakers.
Aerospace series; circuit breakers; technical specification; german version EN 2350:1990
The standard contains the dimensions and masses of sigle-pole circuit beakers up to 25 amp.
Aerospace series; single-pole circuit breakers, temperature compensated rated currents up to 25 A; product standard; german version EN 2495:1990
This standard contains the dimensions and masses of three-pole circuit breakers up to 25 Amp.
Aerospace series; three-pole circuit breakers; temperature compensated rated currents up to 25 A; product standard; german version EN 2592:1990
This industrial standard for the aerospace sector has been drawn up under the responsibility of AECMA (Association Européenne des Constructeurs de Matériel Aérospatial). It is published on yellow paper in three equivalent versions (English, French, German). It will be submitted to CEN (European Committee for Standardization) as a draft European Standard
Aerospace Series Electrical Contacts Used in Elements of Connection Part 013 - Contacts, Electrical, Triaxial, Female 013, Type D, Solder, Class R - Product Standard Issue P 1
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号