共找到 548 条与 航空器及其附件综合 相关的标准,共 37 页
MS26551, dated 17 March 1958, is hereby reinstated as inactive for new design and may be used for acquisition.
STRAINER, 2.5 INCH PRESSURE FUEL SERVICING
This specification is approved for use by all Departments and Agencies of the Department of Defense.
FLASHER, SOLID STATE, AIRCRAFT NAVIGATIONAL LIGHT
This SAE Aerospace Information Report (AIR) provides definitions for terms commonly used in aircraft inflight icing system design and analysis, research, and operations. Some general thermodynamic terms are included that are frequently used in icing analysis, but this document is not meant to be an inclusive list of such terms. The purpose of this document is to provide an assemblage of definitions for terms commonly used in aircraft icing. Over time, the field of aircraft icing has evolved a set of terms that are sometimes used in different ways and have different meanings. This document is a compendium of icing terms and their associated definitions. The SAE does not endorse or recommend any particular definition given in this report.
Aircraft Inflight Icing Terminology
This list has been prepared for use by or for the Government in the acquisition of products covered by the subject specification and such listing of a product is not intended to and does not connote endorsements of the product by the Department of Defense
COUPLING HALF, QUICK DISCONNECT, PNEUMATIC STARTER, EXTERNAL, LOW PRESSURE
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
Aerospace Series Cable Ties for Harnesses Test Methods Part 301: Salt Mist Test Edition P 1
This SAE Aerospace Information Report (AIR) identifies current nondestructive inspection (NDI) methods used to insure product integrity and maximize "in service" life of the major structural components of aircraft wheel and brake assemblies.
Nondestructive Inspection (NDI) Methods Used During Production and Operation of Aircraft Wheels and Brakes
A-A-52304, dated 15 May 1992, has been reviewed and determined to be valid for use in acquistion.
LETTERING SETS AND ACCESSORIES
Provisions for Automatic Test Equipment
Provisions for Automatic Test Equipment
Built-In Test Equipment (Bite)
Built-In Test Equipment (Bite)
Provisions for Automatic Test Equipment
Provisions for Automatic Test Equipment
Built-In Test Equipment (BITE)
Built-In Test Equipment (BITE)
Standard Measurements for Flight Simulator Quality
Standard Measurements for Flight Simulator Quality
Standard Measurements for Flight Simulator Quality
Standard Measurements for Flight Simulator Quality
Qualified Products List QPL-7780-11, dated 5 September 1977, is hereby inactive for new design.
STARTER; ELECTRIC, CONSTANT CURRENT, DC
Cabin Equipment Interfaces Part 1 Head End Equipment Protocol
Cabin Equipment Interfaces Part 1 Head End Equipment Protocol
Cabin Equipment Interfaces Part 1 Head End Equipment Protocol
Cabin Equipment Interfaces Part 1 Head End Equipment Protocol
MIL-F-25173A, dated 16 FEBRUARY 1956, is hereby reactivated and may be used for either new or existing design acquisition.
FASTENER, CONTROL PANEL, AIRCRAFT EQUIPMENT
This standard specifies the characteristics of solid rivets, with universal head, in titanium alloy Ti44,5 Cb, with aluminium pigmented coating, metric series, for maximum operating temperature 235 ℃
Aerospace Series Cable Ties for Harnesses Test Methods Part 100: General Edition P 1
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
Aerospace Series Cable Ties for Harnesses Test Methods Part 202: Examination of Mass and Dimensions Edition P 1
This standard specifies the characteristics of solid rivets, with universal head, in titanium alloy Ti44,5 Cb, with aluminium pigmented coating, metric series, for maximum operating temperature 235 ℃
Aerospace Series Cable Ties for Harnesses Test Methods Part 201: Visual Examination Edition P 1
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号