V90 航空器与航天器制造用设备综合 标准查询与下载

KS W 1130-2002 航空航天工艺.铝合金的阳极处理.非染色涂层的硫酸工艺规程

이 규격은 알루미늄 합금에 시행하는 비염색 양극 산화 피막의 생성 및 시험에 관한 요구

Aerospace process－Anodic treatment of aluminium alloys－Sulfuric acid process, undyed coating

KS W 1120-2001 航空器铝和铝合金的化学转化膜覆层

이 규격은 알루미늄합금의 일반용 화성 피막의 생성 및 시험에 대한 요구 사항에 대하여 규정

Aerospace process-Chemical conversion coatingfor aluminium alloys-General purpose

AECMA PREN 4491-2001 航空航天系列非金属材料厌氧可聚化合物　螺纹锁具　抗扭强度16 Nm

This standard specifies the required characteristics for lamp, code 306, used on-board aircraft. It shall be used together with EN 2756.

Aerospace Series Non-Metallic Materials Anaerobic Polymerisable Compounds Threadlocking Torque Strength 16 Nm Edition P1

AECMA PREN 4492-2001 航空航天系列非金属材料厌氧可聚化合物　螺纹锁具　抗扭强度19 Nm

This “Aerospace Series” Prestandard has been drawn upc under the responsibility of AECMA (The European Association of Aerospace Industries). It is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Technical Committee following comment by the Member countries.

Aerospace Series Non-Metallic Materials Anaerobic Polymerisable Compounds Threadlocking Torque Strength 19 Nm Edition P 1

AECMA PREN 4488-2001 航空航天系列非金属材料厌氧可聚化合物　螺纹锁具　抗扭强度2 Nm

This "Aerospace Series" Prestandard has been drawn up under the responsibility of AECMA-STAN (The European Association of Aerospace Industries - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments.

Aerospace Series Non-Metallic Materials Anaerobic Polymerisable Compounds Threadlocking Torque Strength 2 Nm Edition P 1

AECMA PREN 4489-2001 航空航天系列非金属材料厌氧可聚化合物　螺纹锁具　抗扭强度5 Nm

This "Aerospace Series" Prestandard has been drawn up under the responsibility of AECMA

Aerospace Series Non-Metallic Materials Anaerobic Polymerisable Compounds Threadlocking Torque Strength 5 Nm Edition P 1

AECMA PREN 4490-2001 航空航天系列非金属材料厌氧可聚化合物　螺纹锁具　抗扭强度10 Nm

This "Aerospace Series" Prestandard has been drawn up under the responsibility of AECMA (The European Association of Aerospace Industries). It is published on green paper for the needs of AECMAMembers. It has been technically approved by the experts of the concerned Technical Committee following comment by the Member countries.

Aerospace Series Non-Metallic Materials Anaerobic Polymerisable Compounds Threadlocking Torque Strength 10 Nm Edition P 1

HB 900-2000 飞机制造用试验设备零组件技术条件

本标准规定了航空行业标准《飞机制造用试验设备零组件》制造、检验以及标志、贮存、包装和运输要求。 本标准适用于航空行业标准《飞机制造用试验设备零组件》（以下简称零组件）。

Specifications for parts and components of test equipment used in aircraft manufacturing

AECMA PREN 2916-1999 航空航天系列FE-PM3801(X5CrNiCu17-4)可消耗电级重熔液体和沉积处理棒材直径D小于或等于200mm Rm ≥965MPa P 2版

This industrial standard for the aerospace sector has been drawn up under the responsibility of AECMA.

Aerospace Series Steel FE-PM3801 (X5CrNiCu17-4) Consumable Electrode Remelted Solution Treated and Precipitation Treated Forgings a or D Less Than or Equal to 200 mm Rm Greater Than or Equal to 965 MPa Edition P 2 [Refer To: DIN DIN EN 2816]

AECMA PREN 2918-1999 航空航天系列FE-PM3801(X5CrNiCu17-4)可消耗电级重熔液体和沉积处理棒材直径D小于或等于200mm,Rm≥ 1 0707 Mpa P 2版

This «Aerospace Series» pre-standard has been drawn up under the responsibility of AECMA (Association Européenne des Constructeurs de Matériel Aérospatial). It is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Commission following comment by the Member countries.

Aerospace Series Steel FE-PM3801 (X5crNiCu17-4) Consumable Electrode Remelted Solution Treated and Precipitation Treated Forgings a or D Less Than or Equal to 200 mm Rm Greater Than or Equal to 1 0707 MPa Edition P 2

AECMA PREN 2915-1999 航空航天系列FE-PM3801(X5CrNiCu17-4)可消耗电级重熔液体和沉积处理棒材直径D小于或等于200mm Rm ≥965MPa P 2版

This "Aerospace Series" Prestandard has been drawn up under the responsibility of AECMA (Association Européenne des Constructeurs de Matériel Aérospatial). It is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Technical Committee following comment by the Member countries.

Aerospace Series Steel FE-PM3801 (X5CrNiCu17-4) Consumable Electrode Remelted Solution Treated and Precipitation Treated Bar a or D Less Than or Equal to 200 mm Rm Greater Than or Equal to 965 MPa Edition P 2

AECMA PREN 2917-1999 航空航天系列FE-PM3801(X5CrNiCu17-4)可消耗电级重熔液体和沉积处理棒材直径D小于或等于200mm,Rm≥1070 Mpa P 2版

This standard is part of the series of EN metallic material standards for aerospace applications. The general organization of this series is described in EN 4258. This standard has been prepared in accordance with EN 4500-5.

Aerospace Series Steel FE-PM3801 (X5CrNiCu17-4) Consumable Electrode Remelted Solution Treated and Precipitation Treated Bar a or D Less Than or Equal to 200 mm Rm Greater Than or Equal to 1 070 MPa Edition P 2 [Refer To: DIN DIN EN 2817]

AECMA PREN 3708-001-1996 航空航天系列. 模块化互连系统的终端连接系统.第001 部分:技术规格

This standard specifies an anaerobic polymerisable compound which polymerises upon the exclusion of oxygen and activation by a metal surface with a torque strength of 16 Nm and a viscosity of 500 mm2s-1.

Aerospace Series Modular Interconnection Systems Terminal Junction Systems Part 001 : Technical Specification Edition P 2

AECMA PREN 3708-002-1996 航空航天系列. 模块化互连系统的终端连接系统.第002 部分:技术规格

This standard specifies the particular requirements for aluminium and aluminium alloy wire intended for rivet manufacture. This standard shall be used in conjunction with EN2070-1.

Aerospace Series Modular Interconnection Systems Terminal Junction Systems Part 002 : Perfomance Specification Edition P 2

HB/Z 270-1995 压铸模设计与制造指南

本标准规定了有色金属压铸模具的设计程序和依据，选用材料和热处理、模具设计内容及方法、模具的检验和验收等。 　　本标准适用于有色金属压铸模具的设计、制造和验收。

Die Casting Die Design and Manufacturing Guide

HB/Z 268-1995 冲裁模设计与制造指南

本标准规定了冲裁模的设计程序和依据、模具结构、常用装置、特种冲裁模具的设计、模具计算方法、模具标准件的选用原则、模具材料及热处理要求，以及模具零件、模架和模具装配试模的技术要求。 　　本标准适用于冲孔、落料、复合、级进等冲裁模具的设计和制造，也适用于其它冲模的设计和制造。

Blanking Die Design and Manufacturing Guidelines

AECMA PREN 3708-004-1995 航空航天系列. 模块化互连系统的终端连接系统.第004部分:可拆卸反馈模块版本 密封产品标准

The text of this standard, which exists in three equivalent versions (English, French, German) has been drawn up under the responsibility of AECMA (Association Européenne des Constructeurs de Matériel Aérospatial) and has been circulated to Official Services. Any reservations expressed by Official Services and not resolved in this issue, have been incorporated in the history sheet which has accompanied this prEN to CEN.

Aerospace Series Modular Interconnection Systems Terminal Junction Systems Part 004: Removable Feedback Modules Version, Unsealed, Product Standard Edition P 1

AECMA PREN 3708-003-1995 航空航天系列. 模块化互连系统的终端连接系统.第003部分:可拆卸反馈模块版本 密封产品标准

This standard specifies the required characteristics for lamp, code 7714, used on-board aircraft. It shall be used together with EN 2756.

Aerospace Series Modular Interconnection Systems Terminal Junction Systems Part 003 : Removable Feedback Modules Version, Sealed, Product Standard Edition P 1

AECMA PREN 3708-005-1995 航空航天系列. 模块化互连系统的终端连接系统.第005部分 :带有反馈模块版本配件的框架 密封和未密封的产品标准

This "Aerospace Series" Prestandard has been drawn up under the responsibility of AECMA (The European Association of Aerospace industries). It is published on green paper for the needs of AECMAMembers. If has been technically approved by the experts of the concerned Technical Committee following comment by the Member countries.

Aerospace Series Modular Interconnection Systems Terminal Junction Systems Part 005 : Frames with Accessories for Feedback Modules, Sealed and Unsealed Product Standard Edition P 1

KS W 1129-1995 航空航天.锻铝和铝合金.验收试验和交货要求.第1部分:通用要求

이 규격은 항공우주에 적용을 위한 가공용 알루미늄과 알루미늄 합금의 검사, 시험 및 공급에

Aerospace-Wrought aluminium and aluminium alloys-Inspection,testing and supply requirements-Part 1 : General requirements