W30 麻纺织综合 标准查询与下载

KS K 0425-2010 亚麻纱纱支测定法

이 표준은 마사의 번수 시험방법에 대하여 규정한다. 다만, 황마사의 번수 측정 방법에는 적

Test method for yarn number of linen yarn

KS K 3707-2010 韩山苎麻布料

이 표준은 한산 모시 중급 표백포(이하 모시라 한다.)에 대하여 규정한다.

Hansan ramie cloth

KS K 0219-2010 聚亚安酯纱试验法

이 표준은 폴리우레탄 탄성사의 시험방법에 대하여 규정한다.

Test method for polyurethane thread

KS K 0319-2010 大麻纤维鉴别法

이 표준은 대마 섬유를 다른 섬유와 감별하는 방법에 대하여 규정한다.

Identification of hemp

KS K 3708-2010 黄麻毡

이 표준은 황마 펠트에 대하여 규정한다.

Jute felts

KS K 0318-2010 亚麻维鉴别法

이 표준은 아마 섬유를 다른 섬유와 감별하는 방법에 대하여 규정한다.

Identification of flax

KS K 0307-2010 马尼拉麻的鉴别法:显微镜测定

이 표준은 현미경으로 마닐라마 섬유를 다른 섬유와 감별하는 방법에 대하여 규정한다. 다만,

Identification of manila hemp(Abaca):Microscopic method

KS K 0308-2010 剑麻的鉴别法:灰分测定

이 표준은 사이설마 섬유를 다른 섬유와 감별하는 방법에 대하여 규정한다.또한, 마닐라마

Identification of sisal hemp

KS K 0306-2010 马尼拉麻的鉴别法:灰分测定

이 표준은 마닐라마 섬유를 다른 섬유와 감별할 때 및 마닐라마 섬유가 다른 섬유와 혼용되어

Identification of manila hemp(abaca):Ash method

KS K 0303-2010 黄麻的鉴别法

이 표준은 황마 섬유를 다른 섬유와 감별하는 방법에 대하여 규정한다

Identification of jute

KS K 0309-2010 苎麻的鉴别法

이 표준은 저마 섬유를 다른 섬유와 감별하는 방법에 대하여 규정한다.

Identification of ramie

SN/T 2467-2010 再生纤维素纤维与麻纤维混纺产品定量分析方法 盐酸法

本标准规定了再生纤维素纤维(如:粘胶、铜氨、莫代尔、莱赛尔纤维、竹浆纤维等)与麻纤维混纺纺织品定量分析方法。 本标准适用于再生纤维素纤维(如:粘胶、铜氨、莫代尔、莱赛尔纤维、竹浆纤维等)与麻纤维混纺纺织品的定量分析。 本标准不适用于下述两种情况：a)混纺产品中的麻纤维已经受到严重的化学降解;b)再生纤维素纤维存在不能完全去除的耐久性整理剂或活性染料，致使其不能完全溶解。

Mixtures of regenerated cellulose fibres and flax fibres-Quantitative chemical analysis-Method using hydrochloric acid

NY/T 250-2009 剑麻纱线断裂强力的测定

本标准规定了剑麻纱线断裂强力的测定方法。 本标准适用于剑麻纤维为原料纺制的纱线。

Determination of breaking force for sisal yarn

NY/T 1802-2009 剑麻产品质量分级规则

本标准规定了剑麻产品质量的分级原则、分级要求、等级评定及等级标志。 本标准适用于剑麻纤维及制品质量的分级。

Classification regulation for product quality of sisal

FZ/T 30003-2009 麻棉混纺产品定量分析方法.显微投影法

本标准规定了用显微投影仪、数字式图像分析仪对麻棉混纺产品定量分析的试验方法。 本标准适用于苎麻棉、亚麻棉、大麻棉混纺产品。

Method for quantitative analysis of ramie(flax hemp) cotton blended textile.Micro projection

FZ/T 34008-2009 汽车用亚麻坐垫

本标准规定了汽车用亚麻座垫的术语和定义、产品规格、要求、试验方法、检验规则、标志、包装和运输。 本标准适用于主料亚麻纤维含量在50%及以上的机编、手编座垫。

Flax cushion for motorcar

FZ/T 30004-2009 苎麻织物刺痒感测定方法

本标准规定了含苎麻织物刺痒感程度的一种测定方法。 本标准适用于含苎麻纤维类普通织物刺痒感程度的测定。 本标准不适用于具有特殊布面毛羽特征（如起绒、起圈织物等）苎麻类织物刺痒感程度的测定。

Test method of ramie fabric evoked prickle

FZ/T 30005-2009 苎麻织物刺痒感评价方法

本标准规定了苎麻纤维织物刺痒感的主观评价方法。 本标准适用于含苎麻纤维的织物刺痒感程度的主观评价。

Subjective evaluation method of ramie of ramie evoked prickle

ASTM D6961/D6961M-09 亚麻纤维颜色测量标准试验方法

Few standards exist to objectively judge flax quality. Color is an important factor in the quality of flax fiber. Natural variations in raw flax fiber, various processing steps, fiber blending, and a wide range of end uses contribute to the need for a standard method of objectively measuring the color of flax fiber. Spectrophotometic data provide an accurate, precise determination of the color of flax fiber. Colorimetric data are obtained through specimen measurement by combining specimen spectral data with data representing a CIE standard observer and a CIE standard illuminant, as described in Method E308. If there are differences of practical significance between reported test results for two (or more) laboratories, comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, use the samples for such a comparative test that are as homogeneous as possible, drawn from the same lot of material as the samples that resulted in disparate results during initial testing and randomly assigned in equal numbers to each laboratory. The results from the laboratories involved should be compared using a statistical test for unpaired data, a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results for that fiber sample type must be adjusted in consideration of the known bias.1.1 This test method covers the instrumental color measurement of flax fiber. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Color Measurement of Flax Fiber

ASTM D7025-09 评估清洁亚麻纤维细度的标准试验方法

This test method for determining fineness of cleaned flax fibers is considered satisfactory for acceptance testing of commercial shipments when the levels are controlled by use of a range of calibration standards. If there are differences of practical significance between reported test results for two or more laboratories, comparative tests should be performed by those laboratories to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, use test samples that are as homogenous as possible, are drawn from the material from which the disparate test results were obtained, and are randomly assigned in equal numbers to each laboratory for testing. These test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias. The resistance that a plug of flax fibers offers to the flow of air is measured as an approximate indication of the average relative fineness of the fibers. The total surface area of finer fibers has a larger per unit mass and increased resistance to airflow than do coarser fibers. Instruments are available to indicate the resistance to air flow using either compressed air or a vacuum; and are constructed (1) to measure airflow under constant pressure drop across the plug, (2) to measure pressure drop when a constant flow of air is maintained, or (3) to indicate resistance to air flow from both a balanced and unbalanced Wheatstone bridge. The reliability of the results of any test method depends primarily upon how well the specimens tested represent the original source material. Flax fibers are different from many textile fibers, such as cotton or synthetic ones, in that they are not individual filaments but bundles of fibrous material that may or may not be completely separated into individual filaments and therefore have a high degree of variability. While cleaning and processing can produce separation and changes in length, there is no certainty of fibrillation of the fibrous material. Note 38212;A modification of this test method can be used in commercial trading to select bales that will conform to contract guarantees for specified specific surface index. For this purpose, the usual practice to test only one specimen per sample. This specific surface index reading is related to the average linear density of single fibers in a bundle calculated from mass and length measurements on the bundle and the number of single fibers in the bundle. The specific surface index of flax fibers may be a function of fineness, degree of retting, cleanliness, variety, bundle separation, and plant maturity harvest date. This fineness of flax fibers affects their mill processing and spinning performance as well as contributes significantly to the appearance and strength of the yarns produced. The accuracy of weighing can be controlled by the number of fibers composing the bundle. However, with short fiber of low linear density the number of fibers to be counted becomes prohibitive unless the bundle mass is kept low.1.1 This test method provides two options that cover the determination of the fineness of clean loose flax fibers by: Option 1, measuring the specific surface area by the resistance of a plug of flax fibers to air flow under prescribed conditions, or Option 2, estimating the mass per unit length. Note 18212;For other methods for determining the fineness of fibers refer to Appendix X1. 1.2 The values stated......

Standard Test Method for Assessing Clean Flax Fiber Fineness