W43 丝和丝交织品 标准查询与下载

FZ/T 43017-2011 桑蚕丝/氨纶弹力丝织物

本标准规定了桑蚕丝/氨纶弹力丝织物的分类、术语和定义、要求、试验方法、包装、标志和验收规则。 本标准适用于评定各类服用的练白、染色(色织)印花桑蚕丝/氨纶弹力丝织物(桑蚕丝含量在50%及以上)的品质。

Mulberry silk/spandex elastic fabrics

FZ/T 43006-2011 柞蚕绢丝织物

本标准规定了柞蚕绢丝织物的要求、试验方法、包装、标志和验收规则。 本标准适用于评定各类练白、染色和色织的纯柞蚕绢丝织物，及柞蚕绢丝(含50%及以上)与其他纤维交织的丝织物。

Tussah spun silk fabrics

FZ/T 43013-2011 丝绒织物

本标准规定了丝绒织物的术语和定义、要求、试验方法、包装、标志和验收规则。 本标准适用于评定双层组织分割而成的练白、染色、印花、提花和色织机织丝绒织物的品质。

Silk velvet fabrics

FZ/T 43011-2011 织锦丝织物

本标准规定了织锦丝织物的要求、试验方法、包装、标志和验收规则。 本标准适用于评定各类色织提花织棉丝织物的品质。

Brocade silk fabrics

FZ/T 43001-2010 桑蚕紬丝织物

本标准规定了桑蚕紬丝织物的要求、试验方法、检验规则、包装和标志。 本标准适用于评定各类练白、染色(色织)、印花纯桑蚕紬丝织物、桑蚕紬丝交织物品质。

Mulberry noil silk fabrics

FZ/T 43009-2009 桑蚕双宫丝织物

本标准规定了桑蚕双宫丝织物的要求、试验方法、检验规则、包装和标志。 本标准适用于评定各类服用的练白、染色（色织）、印花桑蚕双宫丝纯织、桑蚕丝或双宫丝与其他纱线交织的丝织物的品质。

Mulberry douppion silk fabrics

FZ/T 42001-2008 柞蚕药水丝

本标准规定了柞蚕药水丝和柞蚕药土丝的要求、检验方法、检验规则、包装和标志。 本标准适用于100D(111.1dtex)及以下的柞蚕药水丝和柞蚕药土丝。 本标准不适用于具有特殊风格的特种工艺柞蚕丝。

Tussah silk bleached

FZ/T 43014-2008 丝绸围巾

本标准规定了丝绸围巾的要求、试验方法、检验规则、标志、包装、运输、贮存等。 本标准适用于丝绸围巾、披肩类产品。

Silk and filament yarn scarves

FZ/T 43019-2007 蚕丝装饰织物

本标准规定了蚕丝装饰织物的分类、要求、试验方法、检验规则、包装和标志。 本标准适用于评定家具覆盖类、寝具用品类、悬挂类的纯蚕丝及交织（蚕丝含量在 30% 及以上）的蚕丝装饰机织物的品质。

Silk Furnishing fabrics

FZ/T 43018-2007 蚕丝绒毯

本标准规定了蚕丝绒毯的要求、试验方法、检验规则、标志、包装及贮存等。 本标准适用于面纱（或起绒纱）为纯蚕丝或蚕丝含量在50％及以上的机织绒毯。

Silk velvel blankets

ASTM D3107-07 弹力丝中机织物的拉伸性能用标准试验方法

these test methods are used to determine the stretch, growth and recovery properties that garments made with the fabric tested may be expected to exhibit during use. these test methods is not recommended for acceptance testing of commercial shipments because the between-laboratory precision is known to be poor. 5.2.1 If there are differences of practical significance between reported test results for two or more laboratories, comparative tests should be performed by those laboratories to determine if there is a statistical bias between them, using competent statistical assistance. Use test samples that are as homogeneous as possible, are drawn from the material from which the disparate test results were obtained, and are randomly assigned in equal numbers to each laboratory for testing. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias. Some stretch fabrics are constructed with stretch yarns in only the filling direction. Consequently, for those fabrics, only the filling direction needs to be tested.DESIG: D3107 07 ^TITLE: Standard Test Methods for Stretch Properties of Fabrics Woven from Stretch Yarns ^SCOPE:1. Scope 1.1 These test methods cover the determination of the amount of fabric stretch, fabric growth, and fabric recovery of fabrics woven in whole or in part from stretch yarns after a specified tension and extension.1.2 These test methods are intended for use with woven fabrics exhibiting high stretch (greater than 12 percent) and good recovery properties from low tension (up to 360 g/cm or 2 lb/in. of fabric width). When agreed upon, these test methods can be used for fabrics woven in whole or in part from non-stretch yarns that exhibit limits within the stretch characteristics shown above.1.3 These test methods allow the use of two tension options commonly used in the textile industry; 1.35 kg (3 lb.) and 1.8 kg (4 lb). Several calculations are included for fabric stretch, fabric growth and fabric recovery, and can be used individually when required by individual specifications.1.4 These test methods should not be used to measure breaking elongation of woven fabrics which is covered in Test Method D 5035.1.5 The values stated in either SI units or inch-pound units are to be regarded separately as the standard. Within the text, the inch-pound units are shown in parentheses. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Stretch Properties of Fabrics Woven from Stretch Yarns

ASTM D3107-07e1 弹力纱机织物拉伸性能的标准试验方法

these test methods are used to determine the stretch, growth and recovery properties that garments made with the fabric tested may be expected to exhibit during use. these test methods is not recommended for acceptance testing of commercial shipments because the between-laboratory precision is known to be poor. If there are differences of practical significance between reported test results for two or more laboratories, comparative tests should be performed by those laboratories to determine if there is a statistical bias between them, using competent statistical assistance. Use test samples that are as homogeneous as possible, are drawn from the material from which the disparate test results were obtained, and are randomly assigned in equal numbers to each laboratory for testing. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias. Some stretch fabrics are constructed with stretch yarns in only the filling direction. Consequently, for those fabrics, only the filling direction needs to be tested.1.1 These test methods cover the determination of the amount of fabric stretch, fabric growth, and fabric recovery of fabrics woven in whole or in part from stretch yarns after a specified tension and extension. 1.2 These test methods are intended for use with woven fabrics exhibiting high stretch (greater than 12 percent) and good recovery properties from low tension (up to 360 g/cm or 2 lb/in. of fabric width). When agreed upon, these test methods can be used for fabrics woven in whole or in part from non-stretch yarns that exhibit limits within the stretch characteristics shown above. 1.3 These test methods allow the use of two tension options commonly used in the textile industry; 1.35 kg (3 lb.) and 1.8 kg (4 lb). Several calculations are included for fabric stretch, fabric growth and fabric recovery, and can be used individually when required by individual specifications. 1.4 These test methods should not be used to measure breaking elongation of woven fabrics which is covered in Test Method D5035. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as the standard. Within the text, the inch-pound units are shown in parentheses. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Stretch Properties of Fabrics Woven from Stretch Yarns

ASTM D3107-07(2011) 弹力纱机织物拉伸性能的标准试验方法

these test methods are used to determine the stretch, growth and recovery properties that garments made with the fabric tested may be expected to exhibit during use. these test methods is not recommended for acceptance testing of commercial shipments because the between-laboratory precision is known to be poor. If there are differences of practical significance between reported test results for two or more laboratories, comparative tests should be performed by those laboratories to determine if there is a statistical bias between them, using competent statistical assistance. Use test samples that are as homogeneous as possible, are drawn from the material from which the disparate test results were obtained, and are randomly assigned in equal numbers to each laboratory for testing. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias. Some stretch fabrics are constructed with stretch yarns in only the filling direction. Consequently, for those fabrics, only the filling direction needs to be tested.1.1 These test methods cover the determination of the amount of fabric stretch, fabric growth, and fabric recovery of fabrics woven in whole or in part from stretch yarns after a specified tension and extension. 1.2 These test methods are intended for use with woven fabrics exhibiting high stretch (greater than 12 percent) and good recovery properties from low tension (up to 360 g/cm or 2 lb/in. of fabric width). When agreed upon, these test methods can be used for fabrics woven in whole or in part from non-stretch yarns that exhibit limits within the stretch characteristics shown above. 1.3 These test methods allow the use of two tension options commonly used in the textile industry; 1.35 kg (3 lb.) and 1.8 kg (4 lb). Several calculations are included for fabric stretch, fabric growth and fabric recovery, and can be used individually when required by individual specifications. 1.4 These test methods should not be used to measure breaking elongation of woven fabrics which is covered in Test Method D5035. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as the standard. Within the text, the inch-pound units are shown in parentheses. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Stretch Properties of Fabrics Woven from Stretch Yarns

FZ/T 43010-2006 桑蚕绢丝织物

本标准规定了桑蚕绢丝织物的要求、试验方法、检验规则、包装和标志。 本标准适用于评定各类练白、染色、印花（色织）桑蚕绢丝纯织及交织（桑蚕绢丝含量在50%以上）织物的品质。

Mulberry spun silk fabrics

DIN EN 14697:2005 纺织品.丝绒毛巾和丝绒毛巾织物.规范和试验方法

This document specifies minimum requirements for properties and test methods for the evaluation of new ready-made terry towels and to new terry fabrics, for contract and domestic use. This document covers woven terry structures only. This document does not cover towels used in the health care sector (see ENV 14237) or cabinet roller towels (see EN 13569).#,,#

Textiles - Terry towels and terry towel fabrics - Specification and methods of test; German version EN 14697:2005

FZ/T 42008-2005 竹绢丝

本标准规定了竹绢丝的要求、试验方法、检验规则及包装标志。 本标准适用于经烧毛的双股竹绢丝(其中竹原纤维含量小于50%)的质量判定。

Bamboo-spun silk yarn

FZ/T 42005-2005 桑蚕双宫丝

本标准规定了桑蚕双宫丝的要求、检验方法、检验规则、包装和标志。 本标准适用于评定所有规格的绞装和筒装桑蚕双宫丝的品质。

Douppion silk

NAVY A-A-59323 A-2005 低林特清洁布

This commercial item description (CID) covers the requirements for two low-lint type cleaning cloths.

CLOTHS, CLEANING, LOW-LINT

FZ/T 43004-2004 桑蚕丝纬编针织绸

本标准规定了桑蚕丝纬编针织绸的分类、规格、要求、试验方法、检验规则、包装和标志。 本标准适用于评定练白、染色、印花和色织的桑蚕丝纬编针织绸的品质。 桑蚕绢丝纬编针织绸及桑蚕丝与其他纤维交织或混纺的纬编针织绸可参照执行。

Silk weft knitted fabrics

FZ/T 43017-2003 桑蚕丝/氨纶弹力丝织物

本标准规定了桑蚕丝/氨纶弹力丝织物的分类、要求、试验方法、检验规则、包装和标志。 本标准适用于评定各类服用的练白、染色(色织)印花桑蚕丝/氨纶弹力丝织物(桑蚕丝含量在70%及以上)的品质。

Silk/spandex filament yarn stretch fabrics