W57 纺织复制品 标准查询与下载

ASTM F2236-10 软的婴儿运载工具的消费者安全标准规范

1.1 This consumer safety specification establishes performance requirements, test methods and marking requirements to promote safe use of soft infant carriers. 1.2 This consumer safety specification is intended to minimize the risk of incidents to an infant from the normal use and reasonably foreseeable misuse of these products. 1.3 For purposes of definition, a soft infant carrier is a product, normally of sewn fabric construction, which is designed to contain a full term infant, generally in an upright position, in close proximity to the caregiver. In general, the child will weigh between 7 and 25 lb (3.2 and 11.3 kg). The soft infant carrier is normally “worn” by the caregiver with the carrier, and thus the infant, suspended from one or both shoulders of the caregiver. These products are generally worn on the front of the caregiver's body with the infant either facing towards or away from the caregiver. This consumer safety specification does not include products generally referred to as “slings.” 1.4 No soft infant carrier produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with the specification unless it complies with all of the requirements contained herein. 1.5 This consumer safety specification is not intended to address incidents and injuries resulting from the interaction of other persons or objects with the caregiver and infant while the soft carrier is in use. 1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.7 The following precautionary caveat pertains only to the test method portion, Section 7 of this consumer safety specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Consumer Safety Specification for Soft Infant Carriers

FZ/T 62018-2009 家用羊毛制品

本标准规定了家用羊毛制品的术语和定义、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于以羊毛皮为主要原料生产的各类家用羊毛制品。其他动物毛皮制品也可参照执行。

Household woolfell textiles

FZ/T 62017-2009 毛巾浴衣

本标准规定了毛巾浴衣的号型规格、要求、抽样、试验方法、检验规则、包装和使用说明。 本标准适用于用毛巾布料制成的浴衣、浴裙、浴帽。

Towelling gown

FZ/T 62014-2009 蚊帐

本标准规定了蚊帐的产品分类、要求、试验方法、判定规则、包装和产品使用说明。 本标准适用于鉴定以经编网眼织物为主要原料生产的各种类型的蚊帐成品的品质。其他织物为主要原料的蚊帐可参照执行。

Mosquite net

FZ/T 62012-2009 防螨床上用品

本标准规定了防螨床上用品的要求、检测方法、判定规则、标志和包装。 本标准适用于被、被套、床单、枕、毛毯、垫类产品等防螨床上用品。其他纺织产品的防螨性能可参照执行。

Anti-mite bedding

FZ/T 62015-2009 抗菌毛巾

本标准规定了抗菌毛巾的要求、试验方法、检验规则及标志。 本标准适用于天然纤维、化学纤维以及混纺纤维制成的抗菌毛巾。

Antibacterial towel

FZ/T 62016-2009 无捻毛巾

本标准规定了无捻毛巾的要求、检测方法。 本标准适用于以纺织纤维为原料的机织无捻毛巾产品。

Zero twist towel

FZ/T 62013-2009 再生纤维素纤维凉席

本标准规定了再生纤维素纤维凉席的术语和定义、要求、抽样、试验方法、检验规则、标志和包装。 本标准适用于以再生纤维素纤维为主要原料的各类机织、编织加工而成的凉席。

Regenerated cellulose fiber mat

SANS 1394-1:2009 羽绒被和枕头.第1部分:羽绒填充

Covers the requirements of three types of plumage filled duvets and one type of plumage filled pillow

Duvets and pillows Part 1: Plumage filled

JIS L 1055:2009 窗帘材料遮光效果的试验方法

This Standard specifies the testing methods for evaluating the light blocking effect of curtains or curtain cloths made of fibres.

Testing methods for light blocking effect of curtain materials

SANS 10247:2009 纺织软垫家具的清洁

Covers suitable and appropriate cleaning techniques for textile upholstered domestic and contract furniture. Is not applicable to the cleaning of furniture upholstered in leather or coated fabrics.

The cleaning of textile upholstered furniture

ASTM F2236-09a 婴儿背巾安规

1.1 This consumer safety specification establishes performance requirements, test methods and marking requirements to promote safe use of soft infant carriers. 1.2 This consumer safety specification is intended to minimize the risk of incidents to an infant from the normal use and reasonably foreseeable misuse of these products. 1.3 For purposes of definition, a soft infant carrier is a product, normally of sewn fabric construction, which is designed to contain a full term infant, generally in an upright position, in close proximity to the caregiver. In general, the child will weigh between 7 and 25 lb (3.2 and 11.3 kg). The soft infant carrier is normally “worn” by the caregiver with the carrier, and thus the infant, suspended from one or both shoulders of the caregiver. These products are generally worn on the front of the caregiver''s body with the infant either facing towards or away from the caregiver. This consumer safety specification does not include products generally referred to as “slings.” 1.4 No soft infant carrier produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with the specification unless it complies with all of the requirements contained herein. 1.5 This consumer safety specification is not intended to address incidents and injuries resulting from the interaction of other persons or objects with the caregiver and infant while the soft carrier is in use. 1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.7 The following precautionary caveat pertains only to the test method portion, Section 7 of this consumer safety specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Consumer Safety Specification for Soft Infant Carriers

GOST R 53294-2009 纺织材料.床上用品.软垫家具.百叶窗.窗帘.易燃性试验方法

Textile materials. Bedding articles. Upholstered furniture. Blinds. Curtains. Flammability test methods

ASTM D4771/D4771M-09 室内家具编织装饰用纤维的标准性能规范

Fabrics intended for this end-use should meet all of the requirements listed in Table 1. It should be recognized that fabrics can be produced utilizing an almost infinite number of combinations of construction variables (for example, type of fibers, percentage of fibers, yarn twist, yarn number, warp and pick count, chemical and mechanical finishes.) Additionally, fashion or aesthetics dictate that the ultimate consumer may find acceptable articles made from fabrics that do not conform to all of the requirements in Table 1. Hence, no single performance specification can possibly apply to all the various fabrics that could be utilized for this end-use. The uses and significance of particular properties and test method are discussed in the appropriate sections of the specified test methods.1.1 This performance specification covers the performance requirements for knitted upholstery fabrics as used in the manufacture of new indoor furniture for general domestic use. These requirements apply to both the wale and course directions for those factors where each fabric direction is pertinent. 1.2 This performance specification is not applicable to fabrics used in contract, porch, deck, or lawn furniture; nor for woven fabrics, bonded or laminated fabrics, or surface-coated fabrics (such as vinyls and urethanes). 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 The following safety hazards caveat pertains only to the test methods described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Note 2.

Standard Performance Specification for Knitted Upholstery Fabrics for Indoor Furniture

BS 5867-2:2008 窗帘及遮光帘用织物.可燃性要求.规范

This part of BS 5867 specifies flammability requirements for fabrics and fabric assemblies for use in the production of non-domestic curtains, drapes and window blinds and for finished articles including combinations of curtains and linings when tested by the methods specified in BS EN ISO 6941 and BS EN ISO 15025. Fabrics are tested before any cleansing procedure, to assess them in the form in which they are most commonly used. The procedures specified in BS EN ISO 10528, BS EN 1021-1 and BS 5651 provide suitable methods of cleansing or wetting. Where curtains or drapes are to be produced in a multi-layer fabric construction, it is essential to test the fabrics in the combination in which they are to be used.

Fabrics for curtains, drapes and window blinds – Part 2: Flammability requirements – Specification

FZ/T 62011.1-2008 布艺类产品.第1部分:帷幔

FZ/T 62011的本部分规定了布艺类产品——帷幔的术语和定义、要求、抽样、试验方法、检验规则和标志、包装。 本部分适用于主要部分为纺织原料制成的帷幔(不包括抽纱类)产品。

Indoor ornamental textiles.Part 1:Valance

FZ/T 62011.2-2008 布艺类产品.第2部分:餐用纺织品

FZ/T 62011 的本部分规定了布艺类产品——餐用纺织品的术语和定义、要求、抽样、试验方法、检验规则和标志、包装。 本部分适用于以纺织纤维为原料的机织餐用纺织品。

Indoor ornamental textiles.Part 2: Dinner cloth

FZ/T 01063-2008 涂层织物.抗粘连性的测定

本标准规定了涂层织物抗粘连性的测定方法。 本标准适用于种类涂层织物。如希望采用不同于本标准规定的其他试验条件，则可由合同双主协商确定，但应在试验报告中说明不同之处。

Coated fabrics.Determination of blocking resistance

ASTM D6663-08 单位和家用编织和针织盖被及附属品的标准规范

1.1 This specification covers the evaluation of specific performance characteristics of importance in woven and knit comforter and accessory products, except for pillows and window treatments, for use in institutional and household environments. 1.2 The following safety hazards caveat pertains only to the test methods described in this specification: This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Woven and Knitted Comforter and Accessory Products for Institutional and Household Use

ASTM F1917-08 婴儿被垫和有关辅助品的标准使用安全性能规范

1.1 This consumer safety performance specification establishes safety performance requirements, test methods, and requirements for labeling to minimize the identified hazards to children presented by infant bedding and related accessories as identified in the introduction. 1.2 No infant bedding or related accessory produced after the approval date of the consumer safety performance specification shall indicate, either by label or other means, compliance with this specification unless it conforms to all applicable requirements contained herein. 1.3 The inspection and test procedures contained herein shall be used to determine the conformance of products to the requirements of this consumer safety performance specification. The relevant tests for an infant bedding product or related accessory can be done in any order, except where specified. Each test may be conducted on a different sample, unless otherwise specified. The tests can be considered as qualification tests and not necessarily as quality control tests. These tests shall also be conducted when there is a design or material change in the infant bedding or related accessory item. Each producer or distributor who represents any products as conforming to this specification may utilize statistically based sampling plans that are appropriate and shall keep such essential records as are necessary to document that all of the requirements of this specification have been met. Any test methods that are made mandatory by the CPSC, or any applicable governmental agencies, shall supersede any applicable test methods in this specification. 1.4 These tests are intended to simulate normal use conditions, so as to ensure that hazards are not generated through normal use. The tests shall be carried out in a normal use environment. For example, bumper guards should be secured in a crib as a customer would in actual end use situations. Ties should be tied and untied. While no specific requirements are defined here, the evaluator shall perform enough testing to simulate normal use during the estimated lifetime of the product. The infant bedding product or related accessory shall be inspected after such tests and shall be evaluated according to the relevant requirements listed within this specification. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 The following safety hazards caveat pertains only to the test method portion, Section 7, of this consumer safety performance specification: This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Consumer Safety Performance Specification for Infant Bedding and Related Accessories