Z23 工业废水、污染物分析方法 标准查询与下载

EN 12566-3:2016 高达50PT的小型废水处理系统.第3部分:整装的和/或现场装配的家用污水处理设备

This European Standard specifies requirements, test methods, the marking and evaluation of conformity for packaged and/or site assembled domestic wastewater treatment plants (including guest houses and businesses) used for populations up to 50 inhabitants. Small wastewater treatment plants according to this European Standard are used for the treatment of domestic wastewater. It covers plants made of concrete, steel, PVC-U, Polyethylene (PE), Polypropylene (PP), Glass Reinforced Polyester (GRP-UP), Polydicyclopentadiene (PDCPD), PVC and EPDM. The test methods specified in this European Standard establish the performance of the plant, needed to verify its suitability for the end use (see 5.2). This European Standard applies to small wastewater treatment plants for use buried in the ground where no vehicle loads are applied to the product. This European Standard applies to plants where all prefabricated components are factory or site-assembled by one manufacturer and which are tested as a whole. NOTE In some countries, domestic wastewater treatment plants are followed by other systems to conform to national regulations.

Small wastewater treatment systems for up to 50 PT - Part 3: Packaged and/or site assembled domestic wastewater treatment plants

EN 12566-1:2016 50PT及以下的小型废水处理系统-第1部分:预制化粪池

This part of this standard specifies the requirements for prefabricated septic tanks and ancillary equipment used for the partial treatment of domestic wastewater for a population 50 PT. Pipes sizes, loads, watertightness, marking and quality control are specified. The following cases are excluded: 1) Septic tanks receiving grey water only; 2) In situ constructed septic tanks.

Small wastewater treatment systems for up to 50 PT - Part 1: Prefabricated septic tanks

EN 12566-6:2016 小型废水处理系统可容纳50PT-第6部分:预制处理单元化粪池出水

This European Standard specifies requirements, test methods, evaluation of conformity and marking for prefabricated secondary treatment units used for the treatment of effluent from septic tanks according to EN 12566-1 or EN 12566-4 in small wastewater treatment systems for up to 50 PT. NOTE Equivalent septic effluent may come from existing septic tanks. It applies to the prefabricated secondary treatment unit, where all its components are packaged or site-assembled and placed on the market as a kit by one manufacturer. The prefabricated secondary treatment unit consists of one or more tanks made of concrete, steel, unplasticised polyvinylchloride (PVC-U), polyethylene (PE), glass reinforced polyester (GRP-UP), polypropylene (PP), polydicyclopentadiene (PDCPD) or container made of flexible sheets (HDPE, PP, PVC, EPDM). Other components specified by the manufacturer, such as pipes, pumps and filter material will be considered as part of the unit. This European Standard establishes the performance of the prefabricated secondary treatment units needed to verify their suitability for the end use conditions for which the test methods are specified. This European Standard applies for the packaged and/or site assembled secondary treatment units for use on the top of the ground (outside the building) or buried in the ground where no vehicle loads are applied to the unit. This European Standard does not cover: - non watertight secondary treatment units with direct infiltration into the ground; - retrofit kits.

Small wastewater treatment systems for up to 50 PT - Part 6: Prefabricated treatment units for septic tank effluent

EN 12566-4:2016 小型废水处理系统可容纳50PT-第4部分:由预制袋就地组装化粪池

This European Standard specifies the requirements for septic tanks assembled in situ from prefabricated kits and ancillary equipment where applicable, used outside buildings for the partial treatment of domestic wastewater for a population up to 50 PT. Pipe sizes, loads, watertightness, marking and evaluation of conformity are specified. This European Standard does not apply to septic tanks receiving grey water only.

Small wastewater treatment systems for up to 50 PT - Part 4: Septic tanks assembled in situ from prefabricated kits

BS EN ISO 17943:2016 水质.水中挥发性有机物的测定.顶部空间固相微萃取法(HS-SPME)和随后的气相色谱-质谱法(GC-MS)

Water quality. Determination of volatile organic compounds in water. Method using headspace solid-phase micro-extraction (HS-SPME) followed by gas chromatography-mass spectrometry (GC-MS)

JIS K 0125:2016 工业水和废水中挥发性有机化合物的检测方法

Testing methods for volatile organic compounds in industrial water and waste water

DB37/T 5039-2015 城镇供水水质现场快速检测技术规程

本规程适用于城镇供水的水质现场快速检测。

Technical specification for on-site rapid detection of water quality in urban water supply

DB53/T 625-2014 焦化污水 总磷的测定 磷钼蓝分光光度法

本标准规定了磷钼蓝分光光度法测定焦化污水总磷的方法。 本标准适用于焦化污水中总磷的测定。测定范围(质量浓度)：0.1 mg/L～10.0 mg/L。

Determination of Total Phosphorus in Coking Sewage by Phosphomolybdenum Blue Spectrophotometry

DB53/T 624-2014 焦化污水 硝酸盐氮、亚硝酸盐氮的测定 戴氏合金还原－中和滴定法

本标准规定了戴氏合金还原－中和滴定法测定焦化污水中硝酸盐氮（NO3--N）、亚硝酸盐氮（NO2--N）的方法。 本标准适用于焦化污水中硝酸盐氮（NO3--N）、亚硝酸盐氮（NO2--N）的测定。测定范围（质量浓度）：硝酸盐氮1.0 mg/L～150.0 mg/L，亚硝酸盐氮1.0 mg/L～100.0 mg/L。

Determination of Nitrate Nitrogen and Nitrite Nitrogen in Coking Wastewater by Dairyler's Alloy Reduction-Neutralization Titration

CFR 40-98.386-2013 环境保护. 第98部分:强制性温室气体报告. 第LL子部分:煤基液体燃料供应. 第98.386节:数据报告的要求.

In addition to the information required by §98.3(c), the following requirements apply:

Protection of environment. Part98:Mandatory greenhouse gas reporting. Subpart LL:Suppliers of coal-based liquid fuels. Section98.386:Data reporting requirements.

CFR 40-98.86-2013 环境保护. 第98部分:强制性温室气体报告. 第H子部分:水泥生产. 第98.86节:数据报告的要求.

In addition to the information required by §98.3(c), each annual report must contain the information specified in paragraphs (a) and (b) of this section, as appropriate.

Protection of environment. Part98:Mandatory greenhouse gas reporting. Subpart H:Cement production. Section98.86:Data reporting requirements

BS ISO 21940-31:2013 机械振动. 转子平衡. 机械失衡的敏感性和灵敏度

Mechanical vibration. Rotor balancing. Susceptibility and sensitivity of machines to unbalance

PD CEN/TS 13714-2013 更改ICS号 污泥的特性.与使用或处理有关的污泥管理

This Technical Specification gives guidance for dealing with the production and control of sludge in relation to inputs and treatment and gives a strategic evaluation of recovery, recycling and disposal options for sludge according to its properties and the availability of outlets. This Technical Specification is applicable for sludges from: storm water handling; night soil; urban wastewater collecting systems; urban wastewater treatment plants; treating industrial wastewater similar to urban wastewater (as defined in Directive 91/271/EC [1]); water supply treatment plants; but excluding hazardous sludges from industry.

Characterization of sludges - Sludge management in relation to use or disposal

DIN EN 14701-2:2013 污泥特性.过滤特性.第2部分:专用耐过滤得测定.德文版本EN 14701-2-2013

Characterisation of sludges - Filtration properties - Part 2: Determination of the specific resistance to filtration; German version EN 14701-2:2013

DB31/T 707-2013 废弃电子电气设备回收及处理处置行业废水中重金属、溴系阻燃剂的检测方法

本标准适用于废弃电子电气设备回收及处理处置行业废水中重金属、溴系阻燃剂含量的检测。

Test method of heavy metals and brominated flame retardants in wastewater from recycling, recovery and treatment industry of waste electrical and electronic equipment

EN 14701-2:2013 过滤性能.污泥的表征第2部分:过滤的电阻率的测定

This European Standard specifies a method for determining the specific resistance to filtration of conditioned and non-conditioned sludges, provided that no sedimentation occurs during filtration (i.e. single phase suspension with particles in suspension). This European Standard is applicable to sludges and sludge suspensions from: storm water handling; urban wastewater collecting systems; urban wastewater treatment plants; industrial wastewater that has been treated similarly to urban wastewater (as defined in Directive 91/271/EEC); water supply treatment plants. This method is also applicable to sludge and sludge suspensions of other origins.

Characterisation of sludges - Filtration properties - Part 2: Determination of the specific resistance to filtration

DIN EN 14701-2:2012 污物特性.过滤特性.第2部分:专用耐过滤得测定.德文版本FprEN 14701-2-2012

Characterisation of sludges - Filtration properties - Part 2: Determination of the specific resistance to filtration; German version FprEN 14701-2:2012

ASTM D6009-12 废堆取样的标准指南

This guide is intended to provide guidance for sampling waste piles. It can be used to obtain samples for waste characterization related to use, treatment, or disposal; to monitor an active pile; to prepare for closure of the waste pile; or to investigate the contents of an abandoned pile. Techniques used to sample include both in-place evaluations of the pile and physically removing a sample. In-place evaluations include techniques such as remote sensing, on-site gas analysis, and permeability. Sampling strategy for waste piles is dependent on the following: Project objectives including acceptable levels of error when making decisions; Physical characteristics of the pile, such as its size and configuration, access to all parts of it, and the stability of the pile; Process that generated the waste and the waste characteristics, such as hazardous chemical or physical properties, whether the waste consists of sludges, dry powders, granules or larger grained materials, and the heterogeneity of the wastes; History of the pile, including dates of generation, methods of handling and transport, and current management methods; Regulatory considerations, such as regulatory classification and characterization data; Limits and bias of sampling methods, including bias that may be introduced by waste heterogeneity, sampling design, and sampling equipment. It is recommended that this guide be used in conjunction with Guide D4687, which addresses sampling design, quality assurance, general sampling considerations, preservation and containerization, cleaning equipment, packaging, and chain of custody. A case history of the investigation of a waste pile is included in Appendix X1.1.1 This guide provides guidance for obtaining representative samples from waste piles. Guidance is provided for site evaluation, sampling design, selection of equipment, and data interpretation. 1.2 Waste piles include areas used primarily for waste storage or disposal, including above-grade dry land disposal units. This guide can be applied to sampling municipal waste piles. 1.3 This guide addresses how the choice of sampling design and sampling methods depends on specific features of the pile. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4.1 Exception8212;The inch-pound units in parentheses are included for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Sampling Waste Piles

MT/T 205-2011 煤矿水中硫酸根离子的测定方法

本标准规定了用硫酸钡重量法测定煤矿水中硫酸根离子的含量。 本标准适用于煤矿水中硫酸根离子的测定。

Determination of sulphate radical hydronium in coal-mine water

MT/T 204-2011 煤矿水碱度的测定方法

本标准规定了用酸滴定法测定煤矿水碱度。 本标准适用于煤矿水碱度的测定。

Determination of alkalinity of coal mine water