自动微量倾浊点测试仪
MPC-602/302
New Standard ASTM D6749
No Methanol
新标准ASTM D6749，无甲醛



Model MPC-602/302 has been designed for automatic determination of Pour Point (PP) and Cloud Point (CP) with small specimen size and shorter test time while securing better test precision than the conventional manual method’s. PP measurement is made by utilizing a new automatic method, namely Air Pressure method, which yields eventually no bias against the conventional test method’s, repeatability of 1 ℃, and reproducibility of 2 ℃.(*) This epoch-making accuracy has made PP determination at 1 ℃ intervals make more sense. The CP/PP mode executes a CP determination and then a PP determination consecutively, which further improves the test throughput. MPC-602 is a 6 tests version, and MPC-302 is a 3 tests version of its original single test model (MPC-102L). ASTM has approved the PP test method: ASTM D6749 on “Standard Test Method for Pour Point of Petroleum Products (Automatic Air Pressure Method)”. *Accuracy information is for typical samples.
MPC-102系列自动微量倾浊点测试仪，采用微量法测试样品的倾点，取样量少，测定过程由计算机自动完成，无需人工干预，测定速度快而结果准确。测定样品的同时可同时测定样品的浊点。仪器进行倾点测试时，没有采用传统的“倾斜法”，而采用了新的标准ASTM D6749 “空气加压法”。测试结果与ISO3016和ASTM D97是所描述的倾斜法完全一致。样品的测试间隔为1℃/2℃，并同时连续测试2-3次，测试结果具有更好的重复性和再现性。
MPC系列有多种型号可选择。MPC-302适用于3样品同时测试，MPC-602用于6样品同时测试。MPC-102L是液冷型，MPC-102A是风冷型。

POUR POINT AT 1 ℃ INTERVALS FOR HIGHER YIELD IN PROCESS:
The conventional PP test methods yield a rough PP numbers of multiple of 3 ℃, and thus higher resolution in PP determination has been long awaited for more elaborate process control. With the patented Air Pressure method, PP can be now determined at 1 ℃ intervals with high accuracy, since the disturbance on the formation of wax crystal structure through the test process is at a minimal level. When PP is measured at 1 ℃ intervals, typical repeatability and reproducibility are 1 ℃ and 2 ℃, respectively.
传统的“倾斜法”是按3℃间隔测试样品的倾点，新的标准按1℃间隔测试样品，仪器测试精度大于试验标准测试规定,可以保证试验结果的精度更高。“气压法”也可有效避免降温过程中，样品的蜡状析出和冰晶体对结果的干扰。

EASY SAMPLE HANDLING: 采样少，易操作
Since the required specimen volume is a mere 4.5 ml and the specimen cup is a test-tube type removable jar, the sample handling is extremely easy. 样品仅需求4.5毫升，玻璃小型样品杯是一个可取放的瓶状试管，操作极其简单。

EASY, QUICK, AND PRECISE PP/CP DETERMINATION:
Just set up the specimen, set test parameters, and then press the START key to start a test. Specimen is cooled at the steepest possible rate without affecting the formation/growth of wax crystal, which has been known to be critical in PP/CP determination. For fuel oils, the specimen may be even pre-heated automatically and then cooled for CP/PP determination, which further improves test throughput.
选好样品后，输入测试参数，预期的倾/浊点数据，按下“开始”键。测定过程由仪器自动完成，无需人工干预。当到检测出倾点后，样品被自动加热至与室温一致。从而可在短时间内进行多组测试。
相较于传统测试方式，“气压法”的效率更高，一般只要传统方式的1/3 或 1/2的时间，就可以完成测试。可在短时间内进行多组测试。

TANAKA Mini Pour/Cloud Point Tester, series MPC-602/302
SPECIFICATIONS:

TYPE:
Mini Pour Point(PP) and Cloud Point(CP) tester with 6 test heads (MPC-602) or 3 test heads (MPC-302) in Bench-top package.With sequential CP and PP measurement capability. Sample cooling and pre-heating by Peltier modules with external cooling liquid. 应用“气压法”测试样品倾点(PP)，浊点(CP)，或样品的浊点(CP)+倾点(PP)的连续测定，特有的半导体制冷/加热设计，MPC-302适用于3样品同时测试，MPC-602用于6样品同时测试。

TEST STANDARDS: 适用标准
ASTM D6749/D97, ISO 3016(PP) , （倾点）
ASTM D2500, ISO 3015 (CP) （浊点）

SPECIMEN VOLUME（样品量）: 4.5ml

MEASURING RANGE: (typical*)测试范围
+51 ℃ to -65 ℃ with cooling liquid of -35 ℃ （外接循环制冷源，介质温度约在零下35℃）
+51 ℃ to -60 ℃ with cooling liquid of -25 ℃ （外接循环制冷源，介质温度约在零下25℃）
+51 ℃ to -40 ℃ with tap water of 20 ℃ （直接外接循环水冷，水温约在20℃）

*:Sample viscosity, etc. affects on lowest temperature of the measuring range.
样品本身的低温运动粘度的性质，限制了试验所需要zei低的测试温度。

MEASUREMENT MODES: 测试模式
Selectable from various modes. 可选择多种测试模式
1.CP mode浊点测试模式（每隔0.1 或 1.0℃测试）

2.PP modes: Programmed by the user. Programmable 倾点测试模式，按用户要求组合
parameters are: 需要先选择油品种类，再选择测试温度。
*Amount of applied air pressure for PP detection, to accommodate different sample types: L(low) for diesel fuels, H(high) for lube oils, VH(very high) and UH (ultra high) for residual fuels and similar samples. 按油品种类（L-柴油；H-润滑油；VH或 UH-重油/渣油）
*Testing intervals: 1.0℃, 2.5℃, or 3.0℃ 按温度每隔1.0℃, 2.5℃, 或 3.0℃测试
(In total, 4x3=12 modes for PP.) 以上总计12种组合倾点测试模式

3.CP/PP modes: 浊点+倾点连续测试 （重复测试）
CP is determined and then PP. PP detection is programmable by the user with the same parameters as PP modes’. (12 modes in total.)
到检测出倾点后，样品被自动加热至与室温一致，再次连续测试样品，或再次按不同的模式测试样品，尤其适用于科研场合。


SAMPLE AUTOMATIC PRE-HEATING: 样品自动加热
Automatic preheating at either +45 ℃ or EPP+10 ℃. (EPP=Expected Pour Point)
按试验方法对样品预热步骤的要求，仪器也包括了样品预热的功能。每次测试时，样品会按要求被预热到（45℃）或（预期倾点+10℃）

DISPLAY: （显示）
Test parameters, EPP, bath temperature, sample temperature, PP, and CP displayed on VFD. Temperatures displayed with 0.1 ℃ increments. VFD荧光屏，清晰显示试验参数，冷浴温度，样品温度，倾点，浊点，预期倾点等内容。
温度显示精度0.1℃。



PRINTER: 打印机
(built-in) PP, CP, mode, EPP, etc. printed by thermal printer. 内置热敏式打印机，打印试验结果。

EPP SETTING: 预期倾点设定
EPP(Expected Pour Point) needs to be set prior to test starts. 测试开始时需要输入预期倾点

SPECIMEN CUP: （样品杯）
Cylindrical glass test jar with 4.5ml sample volume.
石英玻璃的小型样品杯，每次试验只需要4.5ml的样品

SENSORS: 传感器
Compound type sensor assembly for PP and CP. 同一仪器既可以检测倾点，也可以检测浊点
PP detected by air pressure method (patented). （专利设计的）气压传感器变化检测倾点
CP detected photo-electrically. 光电传感器检测浊点
PT100 temp. sensors. 铂电阻检测温度

SAMPLE COOLING RATE: 降温速率
As standard, 4 ℃/min. till EPP+40 ℃, and 1 ℃/min. thereafter. Cooling process is programmable.
按标准规定：在预期倾点+40℃以前，降温速率4℃/min；在此以后，降温速率1℃/min。
用户也可以自行设定特殊的降温曲线，便于科研应用。

SAFETY SHUTDOWN: 安全保护
As hot side of Peltier module reaches 60 ℃ while preheating, warning buzzer beeps and heating stops. 半导体热面温度达到（60℃），超过限定时 ，仪器报警提示，并且自动停机

DATA OUTPUT: 数据输出
RS-232C 1 channel标准RS-232C接口，1

POWER REQUIREMENTS: （电源需求）
100, 120, 220, or 240VAC
1.5kW (MPC-602), 1.0kW (MPC-302)

DIMENSIONS AND WEIGHT: （体积和重量）
800Wx550Dx850H, 100kg (MPC-602)
800Wx500Dx800H, 75kg (MPC-302)

ORDERING INFORMATION:
STANDARD ACCESSORIES: （标准附件）

MPC-602
MPC-302

1.Specimen Cup with Reflex Sea样品杯（带反光贴片）
20 pcs
10 pcs

2.Spare Pressure Conducting Tube导压软管
6 pcs
3 pcs

3.AC power cable电源线
1 pc
1 pc

4.Hose and clamps for Chillers软管和夹具
1 set
1 set

5.Instruction manual使用说明书
1 copy
1 copy



OPTIONAL ACCESSORIES: （选购件1）
Water Regulator with Pressure Gauge(for Connecting Tap Water)
循环泵组件 (直接外接水冷专用)

Chillers for -60 ℃ of Measurement: TANAKA TCU-40B, Neslab RTE-740(*1) or Julabo FP-40MC(*2) Use above chiller x 3 sets for MPC-602, 2 sets for MPC-302
试验温度要求-60℃（零下60℃）需要外接循环制冷源，
MPC-602必须外接3台制冷源；MPC-302必须外接2台制冷源
推荐以下型号：
TANAKA TCU-40B（日本田中制）或RTE-740（美国制）或Julabo FP40-MC（德国制）

Chiller for -40 ℃ of Measurement: Use above chiller x 1 set (MPC-602 and 302)
试验温度要求-40℃（零下40℃），MPC-602/302必须外接至少1台循环制冷源

*1: Made in USA. *2: Made in Germany.

SUGGESTED SPARES FOR 2 YEARS: （选购件2，2年维护）

MPC-602
MPC-302

1.Specimen Cup with Reflex Seal样品杯（带反光贴片）
100 pcs
50 pcs

2.Reflex Seal（反光贴片）
120 pcs
60 pcs

3.Pressure Conducting Tube导压软管
30 pcs
15 pcs

4.O-Ring set (G-35 and P-8) O型圈（G-35 +P-8）
12 sets
6 sets

5.Printing Roll Paper 打印纸
40 pcs
20 pcs

MPC-302自动微量倾浊点试验仪信息由上海旭风科学仪器有限公司为您提供，如您想了解更多关于MPC-302自动微量倾浊点试验仪报价、型号、参数等信息，欢迎来电或留言咨询。

注：该产品未在中华人民共和国食品药品监督管理部门申请医疗器械注册和备案，不可用于临床诊断或治疗等相关用途