光电性能The opto-eletronic characteristics
静态参数(@Tc=22±3℃) | ||||||
特性参数Parameters | 符号 Sym. | 测试条件Test conditions | 最小Min | 典型Typ | 最大 Max | 单位 Unit |
光谱响应范围 Response Spectrum | λ | — | 1000~1650 | nm | ||
响应度 Reponsivity | Re | λ=1.55μm,VR=VBR-2V,φe=1μw | 10 | 14 | A/W | |
反向击穿电压 Reverse breakdown voltage | VBR | ID=10mA,Tc=22℃ | 65 | 75 | V | |
工作电压温度系数 Operating voltage temperature coefficient | γ | Tc=-60~+30℃,ID=10mA | 0.1 | V/℃ | ||
暗电流 Dark current | ID | φe=0μw,VR=VBR-2V | 3.0 | nA | ||
结电容 Total capacitance | Ctot | 1MHz,VR=VBR-2V | 0.2 | pF |
盖革模式下性能参数 | ||||||
参数 Parameter | 测试条件 Test conditions | MP5512Y/MP5522Y | MP5513Y/MP5523Y | 单位 Unit | ||
最小值 Min | 最大值Max | 最小值Min | 最大值Max | |||
暗计数率(DCR) | fgate=50kHz,Tgate=10ns,SPDE=10% | 10 | 3 | kHz | ||
单光子探测效率(SPDE) | fgate=fpulse=50kHz,Tgate=10ns, DCR=10kHz,λ=1.55μm, 0.1 photon per pulse | 10 | 20 | % | ||
后脉冲概率(APP) | @2us, fpulse=50kHz, Tgate=10ns, SPDE=10%, λ=1.55μm, 0.1 photon per pulse | 2 | 2 | % | ||
测试条件补充说明: 1 MP5512Y/MP5522Y测试温度为TA= -35℃,MP5513Y/MP5523Y测温度为TA= -43℃ 2过偏压Vob范围:1.0~2.0V 3直流工作电压Vdc范围:(Vbr-1V)~(Vbr-2V) 以上数据仅供参考,用户需要根据实际的应用来选择适合的工作条件。 |
2 最大额定值Maximum ratings
参数 | 条件 | 最小值 | 最大值 | 单位 |
正向电流 Forward current | 连续方式 | 1 | mA | |
正向电压 Forward voltage | 连续方式 | 1 | V | |
反向电流 Reverse current | 连续方式 | 1 | mA | |
反向电压 Reverse voltage | 连续方式 | Vbr+5 | V | |
脉冲方式 | Vbr+10 | |||
入射光功率Optical Power | 连续方式 (CW) | 1 | mW | |
贮存温度 storage temperature | -55 | 85 | ℃ |
2
典型特性曲线The typical characteristical curve
Fig. 1 DCR and APP vs Tempearture of the MP5522Y/MP5512Y when PDE=10%
图1 MP5522Y/MP5512Y PDE=10%时,温度对暗计数率和后脉冲概率的影响
Fig.2 Photocurrent and dark current vs reverse voltages of the MP5522Y/MP5512Y
图2 MP5522Y/MP5512Y光电流-暗电流曲线
2 封装外形及尺寸The package
1. MP5512Y/MP5513Y
2. MP5522Y/MP5523Y
2 引脚定义
管脚 | 符号 | 功能定义 |
1 | P | P(anode) |
2 | G | Case Ground |
3 | N | N (cathode) |
2 注意事项The cautions
— 该器件需要温度反馈工作电压控制
This device needs feedback of voltage temperature when operating.
— 贮运、使用注意静电保护措施
The suitable ESD protecting mersures are recommended in storage, transporting and using.
— 光纤弯曲半径不小于20mm
The fiber bending radius no less than 20mm for avoiding fiber damaged.
— 使用前保证光纤连接处洁净
Be sure the fiber coupling facet is clean before connecting it to opto-circuit.
除厂家/中国总经销商外,我们找不到 InGaAs 单光子雪崩光电二极管 的一般经销商信息,有可能该产品在中国没有其它经销商。
如果您是,请告诉我们,我们的邮件地址是:sales@antpedia.net 请说明: 1.产品名称 2.公司介绍 3.联系方式 |
售后服务
我会维修/培训/做方法
如果您是一名工程师或者专业维修科学 仪器的服务商,都可参与登记,我们的平台 会为您的服务精确的定位并展示。