ISO 5628:2019
纸和板 - 弯曲刚度的确定 - 两点 三点和四点方法的一般原则
Paper and board — Determination of bending stiffness — General principles for two-point, three-point and four-point methods
- 标准号
- ISO 5628:2019
- 发布
- 2019年
- 发布单位
- 国际标准化组织
- 当前最新
- ISO 5628:2019
- 引用标准
- ISO 186 ISO 187 ISO 3034 ISO 534
- 适用范围
- This document specifies three test methods for determining the bending stiffness of paper and paperboard. The test methods differ in the type of loading mode, thus giving rise to the two-point, three-point and four-point bending test methods. For paper and paperboard in a low thickness range, the two-point bending method and the three-point bending method are suitable. For corrugated fibreboard and board with a higher thickness, the four-point bending method is recommended. The measurement conditions are defined in such a way that the test piece is not subjected to any significant permanent deformation during the test, nor is the range of validity of the formulae for calculating the bending stiffness exceeded. In these bending tests, the test pieces of paper and board are regarded as “beams” as defined by the science of the strength of materials, see Reference [2].
ISO 5628:2019相似标准
推荐
领拓带你看懂材料力学性能测试
试验仪器：万能试验机，高速试验机图三 弯曲试验演示应用范围：主要有三点弯曲和四点弯曲两种加载荷方式，测定灰铸铁的抗弯强度测定硬质合金的抗弯强度测量陶瓷材料、工具钢的抗弯强度检测和比较表面热处理层的质量和性能检测材料在受弯曲载荷下作用下的性能部分测试标准： ASTM D7624用于测定聚合物基复合材料的弯曲刚度与强度性能GB/T232-2010《金属材料弯曲试验方法》4、冲击试验冲击试验一般是确定军用...
英斯特朗带你看懂材料力学性能测试
试验仪器：万能试验机，高速试验机图三 弯曲试验演示应用范围：主要有三点弯曲和四点弯曲两种加载荷方式，测定灰铸铁的抗弯强度测定硬质合金的抗弯强度测量陶瓷材料、工具钢的抗弯强度检测和比较表面热处理层的质量和性能检测材料在受弯曲载荷下作用下的性能部分测试标准： ASTM D7624用于测定聚合物基复合材料的弯曲刚度与强度性能GB/T232-2010《金属材料弯曲试验方法》4、冲击试验冲击试验一般是确定军用...
转筒干燥器的结构和强度
两拖轮中心与滚圈中心连线之间的夹角一般为60度，滚圈的数量视转筒长度而定，有两点、三点、四点等，其中两点支承用的最多。 滚圈和拖轮常用铸铁、型钢、铸钢等材料制成。但考虑到滚圈上某一固定位置的接触频率要尽可能小，应使滚圈的直径不要等于拖轮直径的整数倍。 滚圈和拖轮之间的作用力为两圆柱线接触时的接触应力。 ...