ITU-T G.8262.1-2019由ITU-T - International Telecommunication Union/ITU Telcommunication Sector 发布于 2019-01-01,并于 2019-03-20 实施。
。
This Recommendation outlines new requirements for timing devices used in synchronizing network equipment that supports synchronous clocks@ involved in time and phase transport. It supports clock distribution based on network-synchronous line-code methods (e.g.@ synchronous Ethernet@ synchronous optical transport network (OTN) to deliver frequency synchronization). This Recommendation focuses on the requirements for the enhanced synchronous Ethernet equipment clock (eEEC) and the enhanced synchronous OTN equipment clock (eOEC). This Recommendation allows for proper network operation when this clock is timed from another network equipment clock or a higher-quality clock. Included in this Recommendation are requirements for clock accuracy@ noise transfer@ holdover performance@ noise tolerance and noise generation. These requirements apply under the normal environmental conditions specified for the equipment. This Recommendation contains a single option for enhanced synchronous equipment clock. The networks containing enhanced synchronous equipment clock allow the worst-case synchronization reference chain as specified in Figure 8-5 of [ITU-T G.803]. Careful consideration should be taken when using both ITU-T G.8262.1 and ITU-T G.8262 clocks in the same chain as this may lead to not meeting the performance required by the relevant time and phase synchronization application. The highest performance can be achieved in networks where only enhanced EEC or better clocks are implemented@ see [ITU-T G.8261] for the applicable network limits. OTN 3R regenerators@ as specified in [ITU-T G.8251]@ provide through-timing capability and can transmit timing via synchronous OTN. More information on synchronous Ethernet can be found in [ITU-T G.781]@ [ITU-T G.8261] and [ITU-T G.8264]@ and for synchronous OTN can be found in [ITU-T G.709] and [ITU-T G.7041]. NOTE ?C The clock specified in this Recommendation is compatible with the Option 1 clock specified in [ITU-T G.8262].
NTP第一层主服务器通过精确的外部时钟,一般通过GNSS时间信号获取时间信息,并使自身与UTC同步,是整个系统的基础;而第二层则是从第一层获取时间,第三层从第二层获取时间,依次类推。NTP协议解决了以太网中定时同步能力的不足;PTP协议可以实现对各个以太网现场设备进行微妙级的高精度时间控制。...
而通信网络中的时钟同步精度主要取决于时钟源精度和同步传输协议的精度。因此,提高通信网络的时钟同步精度可以从源头和传输协议两个方面进行。作为时钟源头设备的高精度时间服务器(PRTC/ePRTC),可采用卫星授时或者超高精度地面授时。卫星授时存在一定误差、部署成本较高、无法覆盖室内场景,更重要的是存在可靠性和安全性隐患。...
另外,一个大寄存器组使采用了结构性创新的MCU达到10MIPS的极高的性能。PIC18CXXX家族具备的特殊特性能减少外部组件以降低成本,增强系统可靠性并降低功耗。这些特性包括可编程低压检测(LVD)及可编程Brown-Out检测(BOD)。...
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号