GSO ISO 14663-1:2015由GSO 发布于 2015-09-03。
GSO ISO 14663-1:2015在国际标准分类中归属于: 83.080.20 热塑性塑料。
GSO ISO 14663-1:2015 塑料 模压和挤出乙烯/乙烯醇(EVOH)共聚物材料 第1部分:技术规格命名系统和规则的最新版本是哪一版?
最新版本是 GSO ISO 14663-1:2015 。
1.1 This part of ISO 14663 establishes a system of designation for ethylene/vinyl alcohol (EVOH) copolymer thermoplastic materials, which may be used as the basis for specifications. 1.2 The types of ethylene/vinyl alcohol (EVOH) copolymer plastic are differentiated from each other by a classification system based on appropriate levels of the designatory property: melt mass-flow rate and on information about basic polymer parameters, intended application and/or method of processing, important properties, additives, colorants, fillers and reinforcing materials. 1.3 This part of ISO 14663 is applicable to copolymers of ethylene and vinyl alcohol containing from 15 % (m/m) to 60 % (m/m) of ethylene. It applies to materials ready for normal use in the form of powder, granules or pellets, unmodified or modified by colorants, additives, fillers, etc. 1.4 It is not intended to imply that materials having the same designation give necessarily the same performance. This part of ISO 14663 does not provide engineering data, performance data or data on processing conditions which may be required to specify a material for a particular application and/or method of processing. If such additional properties are required, they shall be determined in accordance with the test methods described in part 2 of this International Standard, if suitable. 1.5 In order to specify a thermoplastic material for a particular application or to ensure reproducible processing, additional requirements may be given in data block 5 (see clause 3, introductory paragraph).
X射线设备成像性能验收与稳定性试验2024-12-0110GB/T 21461.1-2023塑料 超高分子量聚乙烯(PE-UHMW)模塑和挤出材料 第1部分:命名系统和分类基础GB/T 21461.1-20082024-06-0111GB/T 21461.2-2023塑料 超高分子量聚乙烯(PE-UHMW)模塑和挤出材料 第2部分:试样制备和性能测定GB/T 21461.2-20082024-06-...
5 JB/T 11340.2-2012 阀控式铅酸蓄电池安全阀 第2部分:塑料壳体 本部分规定了阀控式铅酸蓄电池安全阀用塑料壳体的范围、术语、要求、试验方法、检验规则和标志、包装、搬运和贮存。 本部分适用于阀控式铅酸蓄电池安全阀用塑料壳体。 ...
2009-07-01 66 HG/T 3227.1-2009 轮胎外胎模具 第1部分:活络模具 本标准规定了汽车轮胎外胎活络模具的术语和定义、分类、规格与基本参数、型号编制方法、技术要求、安全要求、试验方法、检验规则及判定、标志、标牌、标签及使用说明书、包装运输和贮存等的要求。 ...
塑料 模塑和挤出用热塑性聚氨酯 第1部分:命名系统和分类基础 2024-03-01 30 GB/T 42919.1-2023 塑料 导热系数和热扩散系数的测定 第1部分:通则...
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号