IEC 60990-1999
接触电流和保护导体电流的测量方法
Methods of measurement of touch current and protective conductor current
IEC 60990-1999 发布历史
This International Standard defines measurement methods for - d.c. or a.c. of sinusoidal or non-sinusoidal waveform, which could flow through the human body, and - current flowing through a protective conductor. The measuring methods recommended for touch current are based upon the possible effects of current flowing through a human body. In this standard, measurements of current through networks representing the impedance of the human body are referred to as measurements of TOUCH CURRENT. These networks are not necessarily valid for the bodies of animals. The specification or implication of specific limit values is not within the scope of this standard. IEC 60479-1 provides information regarding the effects of current passing through the human body from which limit values may be derived. This standard is applicable to all classes of equipment, according to IEC 60536. The methods of measurement in this standard are not intended to be used for - TOUCH CURRENTS having less than 1 s duration, - patient currents as defined in IEC 60601-1, - a.c. at frequencies below 15 Hz, - a.c. in combination with d.c. The use of a single network for a composite indication of the effects of combined a.c. and d.c. has not been investigated, - currents above those chosen for electric burn limits. This basic safety publication is primarily intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. It is not intended for use by manufacturers or certification bodies. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply, unless specifically referred to or included in the relevant publications.
IEC 60990-1999由国际电工委员会 IX-IEC 发布于 1999-08。
IEC 60990-1999 在中国标准分类中归属于: K04 基础标准和通用方法，在国际标准分类中归属于: 13.260 电击防护。
IEC 60990-1999的历代版本如下：
- 1999年08月 IEC 60990-1999 接触电流和保护导体电流的测量方法
- 2016年05月 IEC 60990-2016 接触电流和保护导体电流的测量方法
IEC 60990-1999 接触电流和保护导体电流的测量方法 由 IEC/TR 60990-1990 变更而来。
- 标准号
- IEC 60990-1999
- 发布日期
- 1999年08月
- 实施日期
- 废止日期
- 无
- 中国标准分类号
- K04
- 国际标准分类号
- 13.260
- 发布单位
- IX-IEC
- 代替标准
- IEC 60990-2016
- 被代替标准
- IEC 74/518/FDIS-1999 IEC/TR 60990-1990
- 适用范围
- This International Standard defines measurement methods for - d.c. or a.c. of sinusoidal or non-sinusoidal waveform, which could flow through the human body, and - current flowing through a protective conductor. The measuring methods recommended for touch current are based upon the possible effects of current flowing through a human body. In this standard, measurements of current through networks representing the impedance of the human body are referred to as measurements of TOUCH CURRENT. These networks are not necessarily valid for the bodies of animals. The specification or implication of specific limit values is not within the scope of this standard. IEC 60479-1 provides information regarding the effects of current passing through the human body from which limit values may be derived. This standard is applicable to all classes of equipment, according to IEC 60536. The methods of measurement in this standard are not intended to be used for - TOUCH CURRENTS having less than 1 s duration, - patient currents as defined in IEC 60601-1, - a.c. at frequencies below 15 Hz, - a.c. in combination with d.c. The use of a single network for a composite indication of the effects of combined a.c. and d.c. has not been investigated, - currents above those chosen for electric burn limits. This basic safety publication is primarily intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. It is not intended for use by manufacturers or certification bodies. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply, unless specifically referred to or included in the relevant publications.