ANSI/ASTM D1389-2007
薄层固体电绝缘材料的耐电压测试的试验方法

Test Method for Proof-Voltage Testing of Thin Solid Electrical Insulating Materials

ANSI/ASTM D1389-2007 发布历史

This test method covers a general procedure for proof-voltage testing of thin solid electrical insulating materials at commercial power frequencies. It is intended to apply principally to flat materials but is applicable, with modification, to any form that permits continuously passing the material between suitable electrodes. On extremely thin materials (usually less than 0.05 mm (0.002 in.)), the test results may be influenced more by mechanical damage caused by conditions of test than by dielectric defects. Consequently, this test method is not recommended for use with extremely thin materials, unless prior determination has established that the test results are not influenced by mechanical damage. While the equipment and procedures described in this test method relate specifically to tests made with power frequency ac voltages, similar equipment and procedures are used for proof-voltage tests using dc voltages. To the extent that it applies to dc tests, this test method can serve as a guide for persons making such tests. However, only tests made with power frequency ac voltages can be said to be in accordance with this test method. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7.

ANSI/ASTM D1389-2007由美国国家标准学会 US-ANSI 发布于 2007-05-22。

ANSI/ASTM D1389-2007 在中国标准分类中归属于: K15 电工绝缘材料及其制品，在国际标准分类中归属于: 29.035.20 塑料和橡胶绝缘材料。

ANSI/ASTM D1389-2007的历代版本如下：

• 2007年05月22日 ANSI/ASTM D1389-2007 薄层固体电绝缘材料的耐电压测试的试验方法

非常抱歉，我们暂时无法提供预览，您可以试试： 免费下载 ANSI/ASTM D1389-2007 前三页，或者稍后再访问。

注意： 点击下载后，生成下载文件时间比较长，请耐心等待......

标准号

ANSI/ASTM D1389-2007

发布日期

2007年05月22日

实施日期

废止日期

无

中国标准分类号

K15

国际标准分类号

29.035.20

发布单位

US-ANSI

被代替标准

ANSI/ASTM D1389-2006

适用范围

This test method covers a general procedure for proof-voltage testing of thin solid electrical insulating materials at commercial power frequencies. It is intended to apply principally to flat materials but is applicable, with modification, to any form that permits continuously passing the material between suitable electrodes.<(hoch), > On extremely thin materials (usually less than 0.05 mm (0.002 in.)), the test results may be influenced more by mechanical damage caused by conditions of test than by dielectric defects. Consequently, this test method is not recommended for use with extremely thin materials, unless prior determination has established that the test results are not influenced by mechanical damage. While the equipment and procedures described in this test method relate specifically to tests made with power frequency ac voltages, similar equipment and procedures are used for proof-voltage tests using dc voltages. To the extent that it applies to dc tests, this test method can serve as a guide for persons making such tests. However, only tests made with power frequency ac voltages can be said to be in accordance with this test method. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7.