BS 1726-1-2002
用圆形线材和棒材制的圆柱形螺旋弹簧.规格、公差和测试指南.压力弹簧已作废

Cylindrical helical springs made from round wire and bar - Guide to methods of specifying, tolerances and testing - Compression springs

BS 1726-1-2002 发布历史

This Part of BS 1726 provides guidance on methods of specifying, tolerancing and testing of parallel sided helical compression springs manufactured from circular section material. Two grades of tolerance, 1 and 2, are given for circular section springs. Three types of end coils are provided for, i.e. open end, closed end, and closed and ground end, the last of these being applicable only to springs where the diameter or axial dimension of material is 0.5 mm or greater. This Part of BS 1726 differentiates between springs that have or have not been stress relieved after forming (designated group A), and springs, the material of which has undergone a structural change by heat treatment after forming (designated group B). This standard gives two methods of specifying springs for general purposes and one method of testing springs.

BS 1726-1-2002由英国标准学会 GB-BSI 发布于 2002-09-25，并于 2002-09-25 实施，于 2010-11-30 废止。

BS 1726-1-2002 在中国标准分类中归属于: J26 弹簧，在国际标准分类中归属于: 21.160 弹簧。

BS 1726-1-2002的历代版本如下：

• 1987年05月29日 BS 1726-1-1987 螺旋弹簧.第1部分:压缩螺旋弹簧设计指南
• 2002年09月25日 BS 1726-1-2002 用圆形线材和棒材制的圆柱形螺旋弹簧.规格、公差和测试指南.压力弹簧
• 2010年11月30日 BS 1726-1-2010 用圆形线材和棒材制的圆柱形螺旋弹簧.BS EN 15800标准没有包括的热盘管弹簧和冷盘管弹簧,与一般弹簧的规格和公差的试验方法指南.压缩弹簧

非常抱歉，我们暂时无法提供预览，您可以试试： 免费下载 BS 1726-1-2002 前三页，或者稍后再访问。

注意： 点击下载后，生成下载文件时间比较长，请耐心等待......

标准号

BS 1726-1-2002

发布日期

2002年09月25日

实施日期

2002年09月25日

废止日期

2010-11-30

中国标准分类号

J26

国际标准分类号

21.160

发布单位

GB-BSI

代替标准

BS EN 15800-2008(部分代替) BS 1726-1-2010

适用范围

This Part of BS 1726 provides guidance on methods of specifying, tolerancing and testing of parallel sided helical compression springs manufactured from circular section material. Two grades of tolerance, 1 and 2, are given for circular section springs. Three types of end coils are provided for, i.e. open end, closed end, and closed and ground end, the last of these being applicable only to springs where the diameter or axial dimension of material is 0.5 mm or greater. This Part of BS 1726 differentiates between springs that have or have not been stress relieved after forming (designated group A), and springs, the material of which has undergone a structural change by heat treatment after forming (designated group B). This standard gives two methods of specifying springs for general purposes and one method of testing springs.

BS 1726-1-2002系列标准

谁引用了BS 1726-1-2002 更多引用