IEC 60282-2-2008
高压熔断器.第2部分:冲击式熔断器
High-voltage fuses - Part 2: Expulsion fuses
IEC 60282-2-2008 发布历史
This part of IEC 60282 specifies requirements for expulsion fuses designed for use outdoors or indoors on alternating current systems of 50 Hz and 60 Hz, and of rated voltages exceeding 1 000 V. Expulsion fuses are fuses in which the arc is extinguished by the expulsion effects of the gases produced by the arc. Expulsion fuses are classified according to the TRV (transient recovery voltage) capability in classes A and B. This standard covers only the performance of fuses, each one comprising a specified combination of fuse-base, fuse-carrier and fuse-link which have been tested in accordance with this standard; successful performance of other combinations cannot be implied from this standard. This standard may also be used for non-expulsion fuses in which the interruption process waits for natural current zero to clear the circuit. NOTE 1 See Clause 5andClause 12 for specific information regarding the selection of fuse class. NOTE 2 Fuses required for the protection of capacitors and for transformer circuit applications are subject to additional requirements (see IEC 60549 [1]1 or IEC 60787 [2]). NOTE 3 This standard does not cover load-switching nor fault-making capabilities. Information regarding requirements related to switching capabilities may be found in IEC 60265-1 [3]. NOTE4 This standard does not cover aspects related to the level of noise, nor the emission of hot gases inherent to some types of expulsion fuses during the process of interruption of fault currents.
IEC 60282-2-2008由国际电工委员会 IX-IEC 发布于 2008-04。
IEC 60282-2-2008 在中国标准分类中归属于: K43 高压开关设备，在国际标准分类中归属于: 29.120.50 熔断器和其他过载保护装置。
IEC 60282-2-2008 发布之时，引用了标准
- IEC 60060-1-1989 高压试验技术 第1部分:一般定义和试验要求
- IEC 60071-1-2006 绝缘配合.第1部分:定义、原则和规则
- IEC 60694-1996 高压开关设备和控制设备标准的通用规范
- IEC 60898-1-2002 电气附件.家用和类似设施用的过电流保护断路器.第1部分:交流操作断路器
- IEC 61109-1992 Isolateurs composites destinés aux lignes aériennes à courant alternatif de tension nominale supérieure à 1000 V - Définitions@ méthodes d?essai et critères d?acceptation (Edition 1.0; Amendment 1: 4/1995)
- IEC 61952-2002 架空电线用绝缘子.额定电压为1000V的交流电流用复合线柱绝缘子
- IEC 62271-100-2001 Appareillage A Haute Tension - Partie 100: Disjoncteurs A Courant Alternatif A Haute Tension (Edition 1.0; Replaces IEC 60056 Edition 4.0:1987)
- 112
IEC 60282-2-2008的历代版本如下：
- 1970年 IEC 60282-2-1970 高压熔断器.第2部分:排气式和类似型式熔断器
- 1995年09月 IEC 60282-2-1995 高压熔断器 第2部分:喷射式熔断器
- 1997年12月01日 IEC 60282-2-1997 Fusibles A Haute Tension - Partie 2: Coupe-Circuit A Expulsion (Edition 2.1; Edition 2:1995 Consolidated with Amendment 1:1997)
- 2008年04月 IEC 60282-2-2008 高压熔断器.第2部分:冲击式熔断器
- 标准号
- IEC 60282-2-2008
- 发布日期
- 2008年04月
- 实施日期
- 废止日期
- 无
- 中国标准分类号
- K43
- 国际标准分类号
- 29.120.50
- 发布单位
- 国际电工委员会
- 引用标准
- IEC 60060-1-1989 IEC 60071-1-2006 IEC 60694-1996 IEC 60694/A1-2000 IEC 60694/A2-2001 IEC 60815-1986 IEC 60898-1-2002 IEC 61109-1992 IEC 61952-2002 IEC 62271-100-2001 IEC 62271-100/A1-2002 IEC 62271-100/A2-2006
- 被代替标准
- IEC 60282-2 Edition 2.1-1997 IEC 60282-2 AMD 1-1997 IEC 60282-2-1995 IEC 32A/261/FDIS-2008
- 适用范围
- This part of IEC 60282 specifies requirements for expulsion fuses designed for use outdoors or indoors on alternating current systems of 50 Hz and 60 Hz, and of rated voltages exceeding 1 000 V. Expulsion fuses are fuses in which the arc is extinguished by the expulsion effects of the gases produced by the arc. Expulsion fuses are classified according to the TRV (transient recovery voltage) capability in classes A and B. This standard covers only the performance of fuses, each one comprising a specified combination of fuse-base, fuse-carrier and fuse-link which have been tested in accordance with this standard; successful performance of other combinations cannot be implied from this standard. This standard may also be used for non-expulsion fuses in which the interruption process waits for natural current zero to clear the circuit. NOTE 1 See Clause 5andClause 12 for specific information regarding the selection of fuse class. NOTE 2 Fuses required for the protection of capacitors and for transformer circuit applications are subject to additional requirements (see IEC 60549 [1]1 or IEC 60787 [2]). NOTE 3 This standard does not cover load-switching nor fault-making capabilities. Information regarding requirements related to switching capabilities may be found in IEC 60265-1 [3]. NOTE4 This standard does not cover aspects related to the level of noise, nor the emission of hot gases inherent to some types of expulsion fuses during the process of interruption of fault currents.