DIN EN 13958-2009
铝及铝合金.通用冷拉制圆盘管.规范

Aluminium and aluminium alloys - Cold drawn, round, coiled tube for general applications - Specification; German version EN 13958:2008

DIN EN 13958-2009 发布历史

This European Standard specifies the tolerances on dimensions and form of round aluminium and aluminium alloys porthole extruded and cold drawn tubes with an outside diameter (OD) of over 2 mm up to and including 50 mm supplied in coil form or in straight lengths cut from coiled material: see Figure 1. This European Standard mainly applies to round cold drawn tube for general engineering applications manufactured in lxxx series of aluminium and 3xxx series of alloys. The use of this European Standard for non-standardised lxxx aluminium and 3xxx alloys or alloys from other series, e.g. 5xxx or 6xxx, is subject to agreement between supplier and purchaser. This European Standard only applies to: -- round tube extruded by the porthole/bridge method in coil form and then cold drawn to the final dimensions required; -- tube as above but delivered in straight lengths cut from coiled material. This European Standard does not apply to: -- seamless extruded (die/mandrel method) and drawn tubes (EN 754-7); -- tubes extruded in straight lengths (i.e. not coiled) and drawn (EN 754-8).

DIN EN 13958-2009由德国标准化学会 DE-DIN 发布于 2009-01。

DIN EN 13958-2009 在中国标准分类中归属于: H61 轻金属及其合金，在国际标准分类中归属于: 77.150.10 铝产品。

DIN EN 13958-2009 发布之时，引用了标准

• EN 515 *， 2017-03-01 更新
• EN 573-3 *， 2022-07-22 更新
• EN 754-2 铝及铝合金-冷拔棒材条材和管材-第2部分:力学性能*， 2016-11-01 更新
• EN 12258-1-1998 

* 在 DIN EN 13958-2009 发布之后有更新，请注意新发布标准的变化。

DIN EN 13958-2009的历代版本如下：

• 2009年01月 DIN EN 13958-2009 铝及铝合金.通用冷拉制圆盘管.规范

非常抱歉，我们暂时无法提供预览，您可以试试： 免费下载 DIN EN 13958-2009 前三页，或者稍后再访问。

注意： 点击下载后，生成下载文件时间比较长，请耐心等待......

标准号

DIN EN 13958-2009

发布日期

2009年01月

实施日期

废止日期

无

中国标准分类号

H61

国际标准分类号

77.150.10

发布单位

DE-DIN

引用标准

EN 515 EN 573-3 EN 754-2 EN 12258-1-1998

被代替标准

DIN EN 13958-2003 DIN EN 13958-2007

适用范围

This European Standard specifies the tolerances on dimensions and form of round aluminium and aluminium alloys porthole extruded and cold drawn tubes with an outside diameter (OD) of over 2 mm up to and including 50 mm supplied in coil form or in straight lengths cut from coiled material: see Figure 1. This European Standard mainly applies to round cold drawn tube for general engineering applications manufactured in lxxx series of aluminium and 3xxx series of alloys. The use of this European Standard for non-standardised lxxx aluminium and 3xxx alloys or alloys from other series, e.g. 5xxx or 6xxx, is subject to agreement between supplier and purchaser. This European Standard only applies to: -- round tube extruded by the porthole/bridge method in coil form and then cold drawn to the final dimensions required; -- tube as above but delivered in straight lengths cut from coiled material. This European Standard does not apply to: -- seamless extruded (die/mandrel method) and drawn tubes (EN 754-7); -- tubes extruded in straight lengths (i.e. not coiled) and drawn (EN 754-8).