BS EN ISO 286-2:2010由英国标准学会 GB-BSI 发布于 1990-01-31,并于 1990-01-31 实施。
BS EN ISO 286-2:2010 在中国标准分类中归属于: J04 基础标准与通用方法,在国际标准分类中归属于: 17.040.10 极限和配合,17.040.30 测量仪器仪表。
BS EN ISO 286-2:2010 产品几何规格(GPS)用于线性尺寸公差的 ISO 代码系统 孔和轴的标准公差等级和极限偏差表的最新版本是哪一版?
最新版本是 BS EN ISO 286-2:2010(2013) 。
* 在 BS EN ISO 286-2:2010 发布之后有更新,请注意新发布标准的变化。
This part of ISO 286 gives values of the limit deviations for commonly used tolerance classes for holes and shafts calculated from the tables given in ISO 286-1. This part of ISO 286 covers values for the upper limit deviations ES (for holes) and es (for shafts), and the lower limit deviations EI (for holes) and ei (for shafts) (see Figures 1 and 2). The ISO system for tolerances on linear size provides a system of tolerances and deviations suitable for features of the following types: a) cylinders; b) two parallel opposite surfaces. For simplicity, and also because of the importance of cylindrical workpieces of circular section, only these are referred to explicitly. It should be clearly understood, however, that the tolerances and deviations given in this part of ISO 286 equally apply to workpieces of other than circular sections. In particular, the term “hole” or “shaft” is used to designate features of the cylinder type (e.g. for the tolerancing of the diameter of a hole or shaft) and, for simplicity, these terms are also used for two parallel opposite surfaces (e.g. for the tolerancing of the thickness of a key or the width of a slot). For further information on terminology, symbols, the basis of the system, etc., see ISO 286-1.
需要说明的是,表中Ra采用第1系列值,而旧的国标Ra的极限值为第2系列值,换算时会遇到数值上靠和下靠的问题。我们在表中表值采用上靠,因为这有利于提高产品质量,个别值采用下靠。旧国标的公差等级与表面粗糙度对应的表的内容和形式都比较复杂,对同一公差等级同一尺寸分段同一基本尺寸,孔与轴的表面粗糙度值不相同,不同配合种类数值也不相同,这是由于旧的公差与配合标准(GB159—59)的公差数值与上述因素有关。...
需要说明的是,表中Ra采用第1系列值,而旧的国标Ra的极限值为第2系列值,换算时会遇到数值上靠和下靠的问题。我们在表中表值采用上靠,因为这有利于提高产品质量,个别值采用下靠。旧国标的公差等级与表面粗糙度对应的表的内容和形式都比较复杂,对同一公差等级同一尺寸分段同一基本尺寸,孔与轴的表面粗糙度值不相同,不同配合种类数值也不相同,这是由于旧的公差与配合标准(GB159—59)的公差数值与上述因素有关。...
需要说明的是,表中Ra采用第1系列值,而旧的国标Ra的极限值为第2系列值,换算时会遇到数值上靠和下靠的问题。我们在表中表值采用上靠,因为这有利于提高产品质量,个别值采用下靠。旧国标的公差等级与表面粗糙度对应的表的内容和形式都比较复杂,对同一公差等级同一尺寸分段同一基本尺寸,孔与轴的表面粗糙度值不相同,不同配合种类数值也不相同,这是由于旧的公差与配合标准(GB159—59)的公差数值与上述因素有关。...
详情如下:序号标准编号标准名称代替标准号实施日期1GB/T 1800.1-2020产品几何技术规范(GPS) 线性尺寸公差ISO代号体系 第1部分:公差、偏差和配合的基础GB/T 1800.1-2009,GB/T 1801-20092020/11/12GB/T 1800.2-2020产品几何技术规范(GPS) 线性尺寸公差ISO代号体系 第2部分:标准公差带代号和孔、轴的极限偏差表GB/T 1800.2...
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号