BS 7448-3:2005由英国标准学会 GB-BSI 发布于 2005-03-23,并于 2005-03-23 实施。
BS 7448-3:2005 在中国标准分类中归属于: H23 金属工艺性能试验方法,在国际标准分类中归属于: 77.040.10 金属材料机械试验。
* 在 BS 7448-3:2005 发布之后有更新,请注意新发布标准的变化。
This part of BS 7448 describes a method for determining the opening mode plane strain fracture toughness KIc, the critical crack tip opening displacement (CTOD) fracture toughness and the critical J fracture toughness of metallic materials. The method uses fatigue precracked specimens tested in displacement control at rates of increase in stress intensity factor greater than 3.0 MPa·ms but less than 3 000 MPa·ms during the initial elastic deformation. Stress intensity factors greater than 3 000 MPa·ms are covered in Annex A. These rates are greater than those permitted in BS 7448-1. The definition of fracture toughness values relevant to particular structural integrity assessments is outside the scope of this British Standard. NOTE This standard does not cover integrity assessments. Such assessments are covered in BS 7910. note:1) 1 N.mm = 0.0316 MPa·m = 0.0316 MN·m.
3)新型热处理工艺及表面处理技术4)凿岩刀具形状的设计改进高档轴承钢性能要求o≤7ppm,Ti≤15ppm、夹杂物 A+B+C+D≤2 级,最大颗粒夹杂物DS≤0.5 级,4.5GPa 赫兹应力下的接触疲劳寿命 L10≥5x10 7 次。轴承钢具有接触疲劳强度高、热处理后硬度高、耐磨性高、摩擦系数低、弹性极限高、尺寸稳定性高、冲击韧性和断裂韧性良好、防锈能力强、冷热加工性能强等特性。...
然而,对于低抗张强度的片剂来说,这种裂纹更可能在随后的撞击中扩大化,如图5所示,经跌落试验的片剂缺陷证实了这一点,这种低抗张强度的片剂在较低的压力下被压制成型,孔隙率更高。Roberts等人提出,高孔隙率的材料具有较低的临界应力强度因子(CSIF)。CSIF是断裂力学中用来评估裂纹在结构内传播所需应力的一个参数,较低的CSIF促进裂纹扩展。...
热评定规程 第6部分:在诊断试验中增加因子的多因子评定2022\\7\\11GB/T 20551-2022畜禽屠宰HACCP应用规范2022\\7\\11GB/T 20564.4-2022汽车用高强度冷连轧钢板及钢带 第4部分:低合金高强度钢2022\\7\\11GB/T 20564.5-2022汽车用高强度冷连轧钢板及钢带 第5部分:各向同性钢2022\\7\\11GB/T 20564.6-2022...
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号