BS EN 60400-2008+A1-2011
管状荧光灯和启动器固定装置用灯架

Lampholders for tubular fluorescent lamps and starterholders

BS EN 60400-2008+A1-2011 发布历史

This International Standard states the technical and dimensional requirements for lampholders for tubular fluorescent lamps and for starterholders, and the methods of test to be used in determining the safety and the fit of the lamps in the lampholders and the starters in the starterholders. This standard covers independent lampholders and lampholders for building-in, used with tubular fluorescent lamps provided with caps as listed in Annex A, and independent starterholders and starterholders for building-in, used with starters in accordance with IEC 60155, intended for use in a.c. circuits where the working voltage does not exceed 1 000 V r.m.s. This standard also covers lampholders for single-capped tubular fluorescent lamps integrated in an outer shell and dome similar to Edison screw lampholders (e.g. for G23 and G24 capped lamps). Such lampholders are tested in accordance with the following clauses and subclauses of IEC 60238: 8.4; 8.5; 8.6; 9.3; 10.7; 11; 12.2; 12.5; 12.6; 12.7; 13; 15.3; 15.4; 15.5 and 15.9. This standard also covers lampholders which are integral with a luminaire or intended to be built into appliances. It covers the requirements for the lampholder only. For all other requirements, such as protection against electric shock in the area of the terminals, the requirements of the relevant appliance standard are to be observed and tested after building into the appropriate equipment, when that equipment is tested according to its own standard. Lampholders for use by luminaire manufacturers only are not for retail sale. This standard also applies, as far as is reasonable, to lampholders and starterholders other than the types explicitly mentioned above and to lamp connectors. Where the term "holder" is used in the standard, both lampholders and starterholders are intended. Where the term “bi-pin lampholder” is used, lampholders for wedged caps are also intended.

BS EN 60400-2008+A1-2011由英国标准学会 GB-BSI 发布于 2009-03-01，并于 2009-03-01 实施。

BS EN 60400-2008+A1-2011 在中国标准分类中归属于: K74 灯具附件，在国际标准分类中归属于: 29.140.10 灯头和灯座。

BS EN 60400-2008+A1-2011 发布之时，引用了标准

• IEC 60061-1 *， 2020-11-27 更新
• IEC 60061-2 *， 2020-11-27 更新
• IEC 60061-3 修改件58.灯头、灯座及检验其互换性和安全性的量规.第3部分:量规*， 2020-05-13 更新
• IEC 60068-2-20-1979 环境试验 第2-20部分:试验 试验T:锡焊
• IEC 60068-2-75-1997 电工电子产品环境试验.第2部分:试验方法.试验Eh:锤击试验
• IEC 60081 修改件6.双头荧光灯.性能规范*， 2017-08-25 更新
• IEC 60112-2003 固体绝缘材料的比较起痕指数和耐泄痕指数的测定方法
• IEC 60155 修改件2-荧光灯的辉光起动器
• IEC 60238 修改件2-爱迪生螺旋灯座*， 2020-01-20 更新
• IEC 60352-1-1997 无焊连接 第1部分:无焊绕接 一般要求、试验方法和使用指南
• IEC 60399 修改件1.带灯罩座环的灯座筒螺纹
• IEC 60529-1989 由外壳提供的防护等级(IP代码)
• IEC 60598-1 灯具 - 第1部分:一般要求和测试*， 2020-08-17 更新
• IEC 60664-1-2007 低压系统内设备的绝缘配合.第1部分:原则、要求和试验
• IEC 60695-2-11-2000 着火危险试验 第2-11部分:基于灼热/发热丝的试验方法 最终产物的灼热丝易燃性试验
• IEC 60695-11-5-2004 着火危险试验.第11-5部分:针状火焰试验方法.装置、证实试验协议和指南
• IEC 61199 修改件2.单端荧光灯.安全规范*， 2014-07-30 更新

* 在 BS EN 60400-2008+A1-2011 发布之后有更新，请注意新发布标准的变化。

BS EN 60400-2008+A1-2011的历代版本如下：

• 2009年03月01日 BS EN 60400-2008+A1-2011 管状荧光灯和启动器固定装置用灯架

BS EN 60400-2008+A1-2011 由 BS EN 60400-2000 变更而来。

BS EN 60400-2008+A1-2011 由 BS EN 60400-2008 变更而来。

非常抱歉，我们暂时无法提供预览，您可以试试： 免费下载 BS EN 60400-2008+A1-2011 前三页，或者稍后再访问。

注意： 点击下载后，生成下载文件时间比较长，请耐心等待......

标准号

BS EN 60400-2008+A1-2011

发布日期

2009年03月01日

实施日期

2009年03月01日

废止日期

无

中国标准分类号

K74

国际标准分类号

29.140.10

发布单位

GB-BSI

引用标准

IEC 60061-1 IEC 60061-2 IEC 60061-3 IEC 60068-2-20-1979 IEC 60068-2-75-1997 IEC 60081 IEC 60112-2003 IEC 60155 IEC 60238 IEC 60352-1-1997 IEC 60399 IEC 60529-1989 IEC 60598-1 IEC 60664-1-2007 IEC 60695-2-11-2000 IEC 60695-11-5-2004 IEC 61199 ISO 4046-4-20

被代替标准

03/301472 DC-2003 07/30169004 DC-2007 BS EN 60400-2000 BS EN 60400-2008

适用范围

This International Standard states the technical and dimensional requirements for lampholders for tubular fluorescent lamps and for starterholders, and the methods of test to be used in determining the safety and the fit of the lamps in the lampholders and the starters in the starterholders. This standard covers independent lampholders and lampholders for building-in, used with tubular fluorescent lamps provided with caps as listed in Annex A, and independent starterholders and starterholders for building-in, used with starters in accordance with IEC 60155, intended for use in a.c. circuits where the working voltage does not exceed 1 000 V r.m.s. This standard also covers lampholders for single-capped tubular fluorescent lamps integrated in an outer shell and dome similar to Edison screw lampholders (e.g. for G23 and G24 capped lamps). Such lampholders are tested in accordance with the following clauses and subclauses of IEC 60238: 8.4; 8.5; 8.6; 9.3; 10.7; 11; 12.2; 12.5; 12.6; 12.7; 13; 15.3; 15.4; 15.5 and 15.9. This standard also covers lampholders which are integral with a luminaire or intended to be built into appliances. It covers the requirements for the lampholder only. For all other requirements, such as protection against electric shock in the area of the terminals, the requirements of the relevant appliance standard are to be observed and tested after building into the appropriate equipment, when that equipment is tested according to its own standard. Lampholders for use by luminaire manufacturers only are not for retail sale. This standard also applies, as far as is reasonable, to lampholders and starterholders other than the types explicitly mentioned above and to lamp connectors. Where the term "holder" is used in the standard, both lampholders and starterholders are intended. Where the term “bi-pin lampholder” is used, lampholders for wedged caps are also intended.