ASTM D6886-2012
通过气相色谱法测定在空气干燥涂层中的某个挥发性有机化合物(VOCs)的标准试验方法

Standard Test Method for Determination of the Individual Volatile Organic Compounds (VOCs) in Air-Dry Coatings by Gas Chromatography

非常抱歉，我们暂时无法提供预览，您可以试试： 免费下载 ASTM D6886-2012 前三页，或者稍后再访问。

注意： 点击下载后，生成下载文件时间比较长，请耐心等待......

标准号

ASTM D6886-2012

发布日期

2012年

实施日期

废止日期

无

国际标准分类号

71.040.50 (Physicochemical methods of analysis)

发布单位

US-ASTM

适用范围

In using Practice D3960 to measure the VOC content of waterborne coatings, precision tends to be poor for low VOC content air-dry coatings when the VOC weight fraction is determined indirectly. The present method first identifies and then quantifies the weight fraction of individual VOCs directly in air-dry coatings. The total VOC weight fraction can be obtained by adding the individual weight fraction values (Note 4).

Note 48212;The present method may be used to speciate solvent-borne air-dry coatings. However, since these normally contain high, and often complex, quantities of solvent, precision tends to be better using the methods contained in Practice D3960, where the VOC fraction is determined by a direct weight loss determination.

SPME/GC makes it possible to identify very low levels of volatile compounds in a coating and could serve to make it possible to identify the presence of hazardous air pollutants (HAPs).

1.1 This test method is for the determination of the weight percent of individual volatile organic compounds in air-dry coatings.

1.2 The method can be used to determine the weight fraction VOC content of waterborne coatings in which the material VOC content is below 5 weight percent. The method has been used successfully with higher VOC content waterborne coatings and with solvent-borne coatings (Note 1).

1.3 The method may also be used to measure the exempt volatile organic compound content (acetone, methyl acetate, t-butyl acetate and p-chlorobezotrifluoride) of waterborne and solvent-borne coatings. The methodology is virtually identical to that used in Test Method D6133 which, as written, is specific for only exempt volatile compounds.

1.4 Volatile compounds that are present at the 0.005 weight percent level or greater can be determined.

Note 18212;This test method may be used for the VOC analysis of coatings containing silanes, siloxanes, and silane-siloxane blends. The test method is not suitable for the analysis of coatings that cure by chemical reaction (this includes two-component coatings and coatings which cure when heated) because dilution with a solvent would impede the chemical reaction required for these types of coatings. This test method measures the VOC weight fraction of air-dry coatings directly as opposed to the methods of Practice D3960 which measure the VOC weight fraction of air-dry waterborne coatings indirectly. A direct measurement of VOC weight fraction, particularly in low VOC content waterborne coatings, generally gives better precision. California Polytechnic State University carried out an extensive study for the California Air Resources Board comparing the precision of the direct method with the indirect method (CARB Standard Agreement No. 04.329). This study may be used to decide if the present method or the methods of Practice D3960 are preferred as an analysis method for obtaining the best possible precision for measuring the mass-based VOC content of a specific coating.

1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this sta......

ASTM D6886-2012 中可能用到的仪器设备