ASTM C1550-12a
纤维增强混凝土的弯曲韧性的标准试验方法(利用中心负荷圆形板)
Standard Test Method for Flexural Toughness of Fiber Reinforced Concrete (Using Centrally Loaded Round Panel)
ASTM C1550-12a 发布历史
ASTM C1550-12a由美国材料与试验协会 US-ASTM 发布于 2012。
ASTM C1550-12a 在中国标准分类中归属于: Q13 混凝土、集料、灰浆、砂浆。
ASTM C1550-12a 发布之时，引用了标准
- ASTM C125 与混凝土和混凝土骨料有关的标准术语
- ASTM C31/C31M 现场制作和养护混凝土试样的标准规程
- ASTM C670 建筑材料的试验方法的配备精密度和偏差说明的标准实施指南
ASTM C1550-12a的历代版本如下：
- 2020年 ASTM C1550-20 纤维增强混凝土弯曲韧性的标准试验方法（使用中心加载圆形面板）
- 2019年 ASTM C1550-19 纤维增强混凝土弯曲韧性的标准试验方法（使用中心加载圆形面板）
- 2012年 ASTM C1550-12a 纤维增强混凝土的弯曲韧性的标准试验方法(利用中心负荷圆形板)
- 2012年 ASTM C1550-12 纤维增强混凝土的弯曲韧性的标准试验方法(利用中心负荷圆形板)
- 2010年 ASTM C1550-10a 纤维增强混凝土的挠性强度的标准试验方法(利用中心负荷圆形板)
- 2010年 ASTM C1550-10 纤维增强混凝土弯曲韧性的标准试验方法（使用中心加载圆形面板）
- 2008年 ASTM C1550-08 纤维增强混凝土弯曲韧性的标准试验方法（使用中心加载圆形面板）
- 2005年 ASTM C1550-05 纤维增强混凝土弯曲韧性的标准试验方法（使用中心加载圆形面板）
- 2004年 ASTM C1550-04 纤维增强混凝土歪曲韧性的标准试验方法(利用中心负载圆形板)
- 2003年 ASTM C1550-03a 纤维增强混凝土弯曲韧性的标准试验方法（使用中心加载圆形面板）
- 2003年 ASTM C1550-03 纤维增强混凝土弯曲韧性的标准试验方法（使用中心加载圆形面板）
- 2002年 ASTM C1550-02 纤维增强混凝土弯曲韧性的标准试验方法（使用中心加载圆形面板）
5. Significance and UseTop Bottom
5.1 The post-crack behavior of plate-like, fiber-reinforced concrete structural members is well represented by a centrally loaded round panel test specimen that is simply supported on three pivots symmetrically arranged around its circumference. Such a test panel experiences bi-axial bending in response to a central point load and exhibits a mode of failure related to the in situ behavior of structures. The post-crack performance of round panels subject to a central point load can be represented by the energy absorbed by the panel up to a specified central deflection. In this test method, the energy absorbed up to a specified central deflection is taken to represent the ability of a fiber-reinforced concrete to redistribute stress following cracking.
Note 1???The use of three pivoted point supports in the test configuration results in determinate out-of-plane reactions prior to cracking, however the support reactions are indeterminate after cracking due to the unknown distribution of flexural resistance along each crack. There is also a change in the load resistance mechanism in the specimen as the test proceeds, starting with predominantly flexural resistance and progressing to tensile membrane action around the center as the imposed deflection is increased. The energy absorbed up to a specified central deflection is related to the toughness of the material but is specific to this specimen configuration because it is also determined by the support conditions and size of the specimen. Selection of the most appropriate central deflection to specify depends on the intended application for the material. The energy absorbed up to 5 mm central deflection is applicable to situations in which the material is required to hold cracks tightly closed at low levels of deformation. Examples include final linings in underground civil structures such as railway tunnels that may be required to remain water-tight. The energy absorbed up to 40 mm is more applicable to situations in that the material is expected to suffer severe deformation in situ (for example, shotcrete linings in mine tunnels and temporary linings in swelling ground). Energy absorption up to intermediate values of central deflection can be specified in situations requiring performance at intermediate levels of deformation.5.2 The motivation for use of a round panel with three supports is based on the within-batch repeatability found in laboratory3 and field experience.4 The consistency of the failure mode that arises through the use of three symmetrically arranged support pivots results in low within-batch variability in the energy absorbed by a set of panels up to a specified central deflection. The use of round panels also eliminates the sawing that is required to prepare shotcrete beam specimens.
5.3 The nominal dimensions of the panel are 75 mm in thickness and 800 mm in diameter. Thickness has been shown to strongly influence panel performance in this test, whil............
- 标准号
- ASTM C1550-12a
- 发布
- 2012年
- 发布单位
- 美国材料与试验协会
- 替代标准
- ASTM C1550-19
- 当前最新
- ASTM C1550-20
- 引用标准
- ASTM C125 ASTM C31/C31M ASTM C670