ASTM D4157-13
纺织纤维耐磨性的标准试验方法(摆辊式耐磨试验法)

Standard Test Method for Abrasion Resistance of Textile Fabrics (Oscillatory Cylinder Method)

被代替

ASTM D4157-13 发布历史

ASTM D4157-13由美国材料与试验协会 US-ASTM 发布于 2013。

ASTM D4157-13 在中国标准分类中归属于: W04 基础标准与通用方法。

ASTM D4157-13的历代版本如下：

• 2022年 ASTM D4157-13(2022) 纺织织物耐磨性的标准试验方法（摆动筒法）
• 2013年 ASTM D4157-13(2017) 纺织织物耐磨损性的标准试验方法(振荡圆柱法)
• 2013年 ASTM D4157-13 纺织纤维耐磨性的标准试验方法(摆辊式耐磨试验法)
• 2010年 ASTM D4157-10 纺织纤维耐磨性的标准试验方法(摆辊式耐磨试验法)
• 2007年 ASTM D4157-07 织物抗磨性的标准试验方法(振动气缸法)
• 2002年 ASTM D4157-02 纺织织物耐磨性的标准试验方法（摆动筒法）

5.1 The measurement of the resistance to abrasion of textile and other materials is very complex. The resistance to abrasion is affected by many factors, such as the inherent mechanical properties of the fibers; the dimensions of the fibers; the structure of the yarns; the construction of the fabrics; and the type, kind, and amount of finishing material added to the fibers, yarns, or fabric.

5.2 The resistance to abrasion is also greatly affected by the conditions of the tests, such as the nature of abradant; variable action of the abradant over the area of specimen abraded, the tension of the specimen, the pressure between the specimen and abradant, and the dimensional changes in the specimen.

5.3 Abrasion tests are all subject to variation due to changes in the abradant during specific tests. The abradant must accordingly be changed at frequent intervals or checked periodically against a standard. With disposable abradants, the abradant is used only once or changed after limited use. With permanent abradants that use hardened metal or equivalent surfaces, it is assumed that the abradant will not change appreciably in a specific series of tests, but obviously similar abradants used in different laboratories will not likely change at the same rate due to differences in usage. Permanent abradants may also change due to pick up of finishing or other material from test fabrics and must accordingly be cleaned at frequent intervals. The measurement of the relative amount of abrasion may also be affected by the method of evaluation and may be influenced by the judgment of the operator.

5.4 The resistance of textile materials to abrasion as measured on a testing machine in the laboratory is generally only one of several factors contributing to wear performance or durability as experienced in the actual use of the material. While “abrasion resistance” (often stated in terms of the number of cycles on a specified machine, using a specified technique to produce a specified degree or amount of abrasion) and “durability” (defined as the ability to withstand deterioration or wearing out in use, including the effects of abrasion) are frequently related, the relationship varies with different end uses, and different factors may be necessary in any calculation of predicted durability from specific abrasion data. Laboratory tests may be reliable as an indication of relative end-use performance in cases where the difference in abrasion resistance of various materials is large, but they should not be relied upon where differences in laboratory test findings are small. In general, they should not be relied upon for prediction of actual wear-life in specific end uses unless there are data showing the specific relationship between laboratory abrasion tests and actual wear in the intended end-use.

5.5 These general observations apply to all types of fabrics, including woven, nonwoven, and knit apparel fabrics, household fabrics, industrial fabrics, and floor coverings. It is not surprising, therefore, to find that there are many different types of abrasion testing machines, abradants, testing conditions, testing procedures, methods of evaluation of abrasion resistance, and interpretation of results.

5.6 All the test methods and instruments so far developed for abrasion resistance may show a high degree of variability in results obtained by different operators and in different laboratories; however, they represent the methods now mo......

标准号

ASTM D4157-13

发布

2013年

发布单位

美国材料与试验协会

替代标准

ASTM D4157-13(2017)

当前最新

ASTM D4157-13(2022)

 

 

推荐

谁引用了ASTM D4157-13 更多引用