ASTM C1807-15
采用无源中子测量法对特种核材料 (SNM) 的滞留量进行无损分析的标准指南

Standard Guide for Nondestructive Assay of Special Nuclear Material (SNM) Holdup Using Passive Neutron Measurement Methods

被代替

标准号

ASTM C1807-15

发布

2015年

发布单位

美国材料与试验协会

替代标准

ASTM C1807-15(2023)

当前最新

ASTM C1807-15(2023)

 

 

引用标准

ANSI N15.20 ASTM C1009 ASTM C1455 ASTM C1490 ASTM C1592/C1592M ASTM C1673

适用范围

5.1 This guide assists in satisfying requirements in such areas as safeguards, SNM inventory control, nuclear criticality safety, waste disposal, and decontamination and decommissioning (D&D). This guide can apply to the measurement of holdup in process equipment or discrete items whose neutron production properties may be measured or estimated. These methods may meet target accuracy for items with complex distributions of SNM in the presence of moderators, absorbers, and neutron poisons; however, the results are subject to larger measurement uncertainties than measurements of less complex items.

5.2 Quantitative Measurements—These measurements result in quantification of the mass of SNM in the holdup. They include all the corrections and descriptive information, such as isotopic composition, that are available.

5.2.1 High-quality results require detailed knowledge of radiation sources and detectors, radiation transport, calibration, facility operations, and error analysis. Consultation with qualified NDA personnel is recommended (Guide C1490).

5.2.2 Holdup estimates for a single piece of process equipment or piping often include some compilation of multiple measurements. The holdup estimate must appropriately combine the results of each individual measurement. In addition, uncertainty estimates for each individual measurement must be made and appropriately combined.

5.3 Scan—Radiation scanning, typically gamma, may be used to provide a qualitative description of the extent, location, and the relative quantity of holdup. It can be used to plan or supplement the quantitative neutron measurements. Other indicators (for example, visual) may also indicate a need for a holdup measurement.

5.4 Nuclide Mapping—To appropriately interpret the neutron data, the specific neutron yield is needed. Isotopic measurements to determine the relative isotopic composition of the holdup at specific locations may be required, depending on the facility.

5.5 Spot Check and Verification Measurements—Periodic re-measurement of holdup at a defined point using the same technique and assumptions can be used to detect or track relative changes in the holdup quantity at that point over time. Either a qualitative or quantitative method can be used.

5.6 Indirect Measurements—Neutron measurements do not identify the radionuclide that produced the neutron signal. The specific neutron yield shall be determined independently of the neutron measurement.

5.7 Modeling—Modeling is recommended as an aid in the evaluation of complex measurement situations. Measurement data are used with a radiation transport model that includes a description of the physical location of equipment and materials. Because of the complexity of neutron transport calcu......

2017 年核能科技热点回眸

但是，由于中子源的匮乏，目前很难对核材料在服役条件下的表现进行准确评价，只能依托离子辐照、计算机模拟等手段进行研究。因此，核材料的研发和验证面临许多挑战。针对此问题，2017年国内外公布的两项指引性文件就显得尤其重要。   美国核学会（American Nuclear Society，ANS）主席Andy Klein 公布了2030年之前核领域亟待解决的九大挑战。...

物理学方法在古陶瓷考古中的应用（四）

由红外光谱原理可知该法最大的特点是特征性极明显，就象人的指纹一样，它依据光谱的吸收谱线的形状、相对强度来确定化合物。其次是灵敏度高，测量时间短，近于无损的检测。还有，样品量少且不受状态限制。但是制样必须谨慎，固体多采用压片法或溶解成液体，液体取 1-2 滴于面盐片间即可进行测量，气体需装入专用的吸收瓶（池）内。在考古学中利用红外光谱对陶瓷、青铜器、书画等不同材质的东西进行鉴别。...

如何防核辐射

源材料主要包括天然轴、贫化轴,钍及含上述任何物质的金属、合金、化合物或浓缩物的材料。特种可裂变材料主要包括钚 -239(239pu)、轴-233(233U)、含有富集同位素235 -(235U)的轴。所谓富集,是指轴-235的丰度与轴-238的丰度比大于天然轴中这两个同位素的丰度比。 　　需要重点加以控制和保护,防止其被盗、被破坏、丢失、非法转移和非法使用的核材料是特种可裂变的核材料。...

ICP-MS小白进阶指南

（1）流动注射进样特点：样品用量少，对溶液TDS和粘度要求不高，设备简单灵活；（2）电热蒸发直接进样特点：进样量少，传输率高（＞60%），可预先去除溶剂，可预先去除基体；（3）氢化物发生进样特点：接近于100%的传输率，与溶液基体充分分离，具有预富集的效果；（4）激光烧蚀法进样特点：原位无损分析，重现性好，线性范围宽，适用于多种样品（包括钢铁、陶瓷、矿物、核材料、食品等）。...