ASTM E1105-15
采用统一或循环静态空气压差法现场测定已安装的外窗, 天窗, 门和幕墙渗水度的标准试验方法

Standard Test Method for Field Determination of Water Penetration of Installed Exterior Windows, Skylights, Doors, and Curtain Walls, by Uniform or Cyclic Static Air Pressure Difference

被代替

ASTM E1105-15 发布历史

ASTM E1105-15由美国材料与试验协会 US-ASTM 发布于 2015。

ASTM E1105-15在国际标准分类中归属于: 91.060.50 门窗。

ASTM E1105-15 发布之时，引用了标准

• ASTM E331 用均匀静态气压差法测定外窗、幕墙和门的渗水性的标准试验方法
• ASTM E547 用循环静态气压差法测定外窗、天窗、护墙及门渗水度的标准试验方法
• ASTM E631 房屋结构的标准术语

ASTM E1105-15的历代版本如下：

• 2023年 ASTM E1105-15(2023) 用均匀或循环静态气压差现场测定已安装的外窗、天窗、门和幕墙的水渗透性的标准试验方法
• 2015年 ASTM E1105-15 采用统一或循环静态空气压差法现场测定已安装的外窗, 天窗, 门和幕墙渗水度的标准试验方法
• 2000年 ASTM E1105-00(2008) 用统一的或循环的静态气压差法现场测定已安装的外窗、天窗、护墙及门渗水度的标准试验方法
• 2000年 ASTM E1105-00 用统一的或循环的静态气压差法现场测定已安装的外窗、天窗、护墙及门渗水度的标准测试方法

5.1 This test method is a standard procedure for determining the resistance to water penetration under uniform or cyclic static air pressure differences of installed exterior windows, skylights, curtain walls, and doors. The air-pressure differences acting across a building envelope vary greatly. These factors should be considered fully prior to specifying the test pressure difference to be used.

Note 1: In applying the results of tests by this test method, note that the performance of a wall or its components, or both, may be a function of proper installation and adjustment. In service, the performance will also depend on the rigidity of supporting construction and on the resistance of components to deterioration by various causes, vibration, thermal expansion and contraction, and so forth. It is difficult to simulate the identical complex wetting conditions that can be encountered in service, with large wind-blown water drops, increasing water drop impact pressures with increasing wind velocity, and lateral or upward moving air and water. Some designs are more sensitive than others to this upward moving water.

Note 2: This test method does not identify unobservable liquid water which may penetrate into the test specimen.

5.2 Laboratory tests are designed to give an indication of the performance of an assembly. Field performance may vary from laboratory performance since the supporting structure for the test specimen, methods of mounting, and sealing in the laboratory can only simulate the actual conditions that will exist in the building. Shipping, handling, installation, acts of subsequent trades, aging, and other environmental conditions all may have an adverse effect upon the performance of the installed product. This field test procedure provides a means for determining the performance of a product once installed in the building.

5.3 The field test may be made at the time the window, skylight, curtain-wall, or door assemblies are initially installed and before the interior of the building is finished. At this time, it is generally easier to check the interior surfaces of the assemblies for water penetration and to identify the points of penetration. The major advantage of testing when assemblies are initially installed is that errors in fabrication or installation can be readily discovered and corrections made before the entire wall with its component assemblies is completed at which time the expense of corrective work may be increased many times.

5.4 The field test may also be made after the building is completed and in service to determine whether or not reported leakage problems are due to the failure of the installed assemblies to resist water penetration at the specified static air pressure difference. Generally it is possible to conduct tests on window, skylight, and door assemblies without too much difficulty, and to identify sources of leakage. A curtain-wall assembly, on the other hand, may not be accessible from the inside without the removal of interior finished walls and ceilings. Even with removal of interior walls and ceilings, it may not be possible to observe curtain-wall surfaces behind spandrel beams. The feasibility of conducting a meaningful static air pressure di......

标准号

ASTM E1105-15

发布

2015年

发布单位

美国材料与试验协会

替代标准

ASTM E1105-15(2023)

当前最新

ASTM E1105-15(2023)

 

 

引用标准

ASTM E331 ASTM E547 ASTM E631

推荐

谁引用了ASTM E1105-15 更多引用