ASTM D5126/D5126M-16
测定流区中测定液体传导指数现场比较法的标准指南

Standard Guide for Comparison of Field Methods for Determining Hydraulic Conductivity in Vadose Zone

被代替

ASTM D5126/D5126M-16 发布历史

ASTM D5126/D5126M-16由美国材料与试验协会 US-ASTM 发布于 2016。

ASTM D5126/D5126M-16在国际标准分类中归属于: 07.060 地质学、气象学、水文学。

ASTM D5126/D5126M-16 发布之时，引用了标准

• ASTM D2434 在常水头压力下颗粒状土壤渗水率的标准试验方法
• ASTM D3385 用双环渗透仪现场测定土壤渗透率的标准试验方法
• ASTM D3740 工程设计及建筑中使用的土壤和岩石的试验和或检查中使用试剂评定的规程
• ASTM D4643 微波炉加热测定土壤和岩石含水量的标准试验方法
• ASTM D6026 在土工学数据中使用明显数字的标准实施规程
• ASTM D653 采用流动空气测量未饱和多孔材料渗透性的标准试验方法

ASTM D5126/D5126M-16的历代版本如下：

• 2016年 ASTM D5126-16e1 测定流区中测定液体传导指数现场比较法的标准指南
• 2016年 ASTM D5126/D5126M-16 测定流区中测定液体传导指数现场比较法的标准指南
• 1990年 ASTM D5126/D5126M-90(2010)e1 测定流区中测定液体传导指数现场比较法的标准指南
• 1990年 ASTM D5126-90(2004) 现场比较法测定渗流区液体传导指数的标准指南
• 1990年 ASTM D5126-90(1998)e1 比较渗流带透水性测定用现场方法的标准指南

5.1 Saturated hydraulic conductivity measurements are made for a variety of purposes varying from design of landfills and construction of clay liners to assessment of irrigation systems. Infiltrometers are commonly used where infiltration or percolation rates through a surface or subsurface layer are desired. Evaluation of the rate of water movement through a pond liner is one example of this kind of measurement. Penetration of the liner by a borehole would invalidate the measurement of liner permeability. It has been noted that small-ring infiltrometers are subject to error due to lateral divergence of flow. Therefore, techniques using very large (1 to 2-m diameter) infiltration basins have been recommended for measuring the very slow percolation rates typically needed for clay liners. The air-entry permeameter can be used instead of infiltrometer tests to avoid lateral divergence of flow. However, because a cylinder must be driven into the media tested, the actual soil column tested may be disrupted by introduction of the cylinder, especially in structured soils.

5.2 Borehole tests for determining saturated hydraulic conductivity are applicable for evaluating the rate of water movement through subsurface layers. For slowly permeable layers, an accurate method of measuring the rate of water movement into the borehole will need to be developed. Use of a flexible bag as a reservoir that can be periodically weighed is advisable for these conditions. A number of mathematical solutions for borehole outflow data are available (Stephens et al. (17), Reynolds et al. (18), and Philip (19)).

5.3 Information on unsaturated flow rates is needed to design hazardous waste landfills and impoundments where prevention of flow of contaminants into groundwater is needed. Of the test methods available, the primary differences are cost and resultant bias and precision. The instantaneous profile test method appears to provide very reliable data because it uses a large volume of soil (several cubic metres) and is performed on undisturbed soils in the field. However, a single test can cost several thousand dollars. The gypsum crust test method, although more rapid than the instantaneous profile test method, sacrifices precision of results due to the smaller spatial extent of the tested area. Methods for estimating unsaturated hydraulic conductivity from fundamental soil hydraulic functions like the desorption curves may deviate from true values by an order of magnitude, but may be of use where relative differences in permeability between materials or across water content ranges is of interest.

Note 1: The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned in that compliance with Practice D3740 does not in itself assure reliable results. Reliable results depends on many factors; Practice D3740

标准号

ASTM D5126/D5126M-16

发布

2016年

发布单位

美国材料与试验协会

替代标准

ASTM D5126-16e1

当前最新

ASTM D5126-16e1

 

 

引用标准

ASTM D2434 ASTM D3385 ASTM D3740 ASTM D4643 ASTM D6026 ASTM D653

推荐