4.1 This guide is intended to serve as a reference for the testing of textile composite materials.
1.1 This guide is applicable to the testing of textile composites fabricated using fabric preforms, such as weaves, braids, stitched preforms, and so forth, as the reinforcement. The purpose of this guide is to:
1.1.1 Ensure that proper consideration is given to the unique characteristics of these materials in testing.
1.1.2 Assist the user in selecting the best currently available ASTM test method for the measurement of commonly evaluated material properties for this class of materials.
1.2 Areas where current ASTM test methods do not meet the needs for testing of textile composites are indicated.
1.3 It is not the intent of this guide to cover all test methods which could possibly be used for textile composites. Only the most commonly used and most applicable standards are included.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
部分测试标准: ISO 179-1-2010塑料摆式冲击性能的测定GB/T 15231.5-1994 玻璃纤维增强水泥性能试验方法 抗冲击性能GB/T 14152-2001 热塑性塑料管材耐性外冲击性能 GB/T 21239-2007 纤维增强塑料层合板冲击后压缩性能试验方BS EN 950-1999 门扇.耐坚硬物体冲击性能的测定 DIN ISO 2747-1999 瓷釉和搪瓷.搪瓷烹调器具.耐热冲击性能的测定...
部分测试标准: ISO 179-1-2010塑料摆式冲击性能的测定GB/T 15231.5-1994 玻璃纤维增强水泥性能试验方法 抗冲击性能GB/T 14152-2001 热塑性塑料管材耐性外冲击性能 GB/T 21239-2007 纤维增强塑料层合板冲击后压缩性能试验方BS EN 950-1999 门扇.耐坚硬物体冲击性能的测定 DIN ISO 2747-1999 瓷釉和搪瓷.搪瓷烹调器具.耐热冲击性能的测定...
热固性模塑板料,包括填充和增强材料,热固性板材,包括层压材料纤维增强热固性和热塑性复合材料,其含有单向或非单向的增强材料,如毡纺织纤维纺织粗纱短切原丝组合或混杂增强材料无捻粗纱和磨碎纤维等;由预浸渍材料制成的板材热致液晶聚合物 试验仪器:◎试样的制备仪器:用注塑机制得标准试样五根以上或机加制样◎试验设备主机: DL-D系列电子试验机◎夹具:我们推荐使用三点弯曲加载装制可以评价刚性和半刚性的材料又同时试样的支承跨度...
热固性模塑板料,包括填充和增强材料,热固性板材,包括层压材料纤维增强热固性和热塑性复合材料,其含有单向或非单向的增强材料,如毡纺织纤维纺织粗纱短切原丝组合或混杂增强材料无捻粗纱和磨碎纤维等;由预浸渍材料制成的板材热致液晶聚合物 试验仪器:◎试样的制备仪器:用注塑机制得标准试样五根以上或机加制样◎试验设备主机: KDL电子试验机◎夹具:我们推荐使用三点弯曲加载装制可以评价刚性和半刚性的材料又同时试样的支承跨度...
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号