ASTM C1130-17由美国材料与试验协会 US-ASTM 发布于 2017。
ASTM C1130-17 在中国标准分类中归属于: A54 热学计量,在国际标准分类中归属于: 17.200.10 热、量热学。
5.1 The application of HFTs and temperature sensors to building envelopes provide in-situ data for evaluating the thermal performance of an opaque building component under actual environmental conditions, as described in Practices C1046 and C1155. These applications require calibration of the HFTs at levels of heat flux and temperature consistent with end-use conditions.
5.2 This practice provides calibration procedures for the determination of the heat flux transducer sensitivity, S, that relates the HFT voltage output, E, to a known input value of heat flux, q.
5.2.1 The applied heat flux, q, shall be obtained from steady-state tests conducted in accordance with either Test Method C177, C518, C1363, or C1114.
5.2.2 The resulting voltage output, E, of the heat flux transducer is measured directly using (auxiliary) readout instrumentation connected to the electrical output leads of the sensor.
Note 1: A heat flux transducer (see also Terminology C168) is a thin stable substrate having a low mass in which a temperature difference across the thickness of the device is measured with thermocouples connected electrically in series (that is, a thermopile). Commercial HFTs typically have a central sensing region, a surrounding guard, and an integral temperature sensor that are contained in a thin durable enclosure. Practice C1046, Appendix X2 includes detailed descriptions of the internal constructions of two types of HFTs.
5.3 The HFT sensitivity depends on several factors including, but not limited to, size, thickness, construction, temperature, applied heat flux, and application conditions including adjacent material characteristics and environmental effects.
5.4 The subsequent conversion of the HFT voltage output to heat flux under application conditions requires (1) a standardized technique for determining the HFT sensitivity for the application of interest; and, (2) a comprehensive understanding of the factors affecting its output as described in Practice C1046.
5.5 The installation of a HFT potentially changes the local thermal resistance of the test artifact and the resulting heat flow differs from that for the undisturbed building component.
可存储 1000 次测试、20 个操作员、100 种样品名称、21 种测试方法统计分析(最小值、最大值、平均值、重复性)测量含硅样品的闪点没有任何问题自动点燃测试火焰,通过电子点火器可将其重新点燃,并且在测试结束时可切断气源对不符合技术规格的结果发出讯息提示Pt100 样品温度探头可通过经用户认证的ASTM 温度计进行动态校准,或通过具有21 个校准点的校正表进行校准标准方法:ASTM D92、ISO...
可穿戴温度贴片是患者温度监测系统的新兴发展趋势。设计这些贴片用于临床环境的最大障碍之一是需要满足严格的精度要求。美国材料与试验协会(ASTM)规定了电子患者体温计的精度要求,如表1所示。在最严格的范围内,这些标准允许最多±0.1oC的误差,以确保患者的体温的准确测量。...
点火器通过连接到关闭机制的杠杆进行自动定位 8.排气系统-不锈钢制作,延长寿命。包括罩子,气体样品取样针,排风扇(流量可调,0g/s 至50g/s,精度至少为 0.1g/s),以及孔板流量测试器(热电偶和差压传感器)。...
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号