ISO 11299-2:2018
地下铺设送气管道维修用塑料管道系统. 第2部分: 连续管道衬里
Plastics piping systems for renovation of underground gas supply networks - Part 2: Lining with continuous pipes
- 标准号
- ISO 11299-2:2018
- 发布
- 2018年
- 发布单位
- 国际标准化组织
- 当前最新
- ISO 11299-2:2018
- 引用标准
- EN 1555-1:2010 EN 1555-2:2010 EN 1555-3+A1:2012 EN 1555-5:2010 ISO 11299-1:2018 ISO 12176-1:2017 ISO 12176-2:2008 ISO 4437-1:2014 ISO 4437-2:2014 ISO 4437-3:2014 ISO 4437-5:2014
- 适用范围
- This document, read in conjunction with ISO 11299-1, specifies requirements and test methods for pipes and fittings which are part of plastics piping systems installed as continuous pipes in the renovation of underground gas supply networks. It is applicable to polyethylene (PE) pipes of three different types: — PE solid wall single layered pipes (nominal outside diameter, dn), including any identification stripes; — PE pipes with co-extruded layers on either or both the outside and inside of the pipe (total outside diameter, dn), as specified in Annex A, where all layers have the same MRS rating; — Coated PE pipes (outside diameter, dn) having a peelable, contiguous, thermoplastics additional layer on the outside of the pipe (“coated pipe”), as described in Annex A. In addition it covers: — jointing of pipe lengths by means of butt fusion; — fabricated and injection-moulded fittings made of PE; It is applicable to PE pipes, fittings and assemblies intended to be used at an operating temperature of 20 °C as the reference temperature. NOTE For other operating temperatures, guidance is given in ISO 4437-5:2014.
ISO 11299-2:2018相似标准
推荐
浅谈影响城市供水水质的因素及措施
2、更新或改造供水管道系统,深化管网管理。 ...
电磁流量计的选择与安装注意要点
2、由于工艺配管内流速偏低时而达不到“1”中对应通径下的小上限流量值时，可选择变送器通径小于工艺配管的通径，即在变送器前后加接异径管。 十一、安装形式的选择 1、整体式：即将流量计的传感部分和转换部分装于一体，优点是便于安装。 2、分离式：即将流量计的传感部分安装于被测管道上，将转换部分安装于便于操作的室内。适用于现场环境差的场合（但其分离长度应小于30m）。 ...
电磁流量汁的正确选择和正确使用
1.4 关于接地环的选用 电磁流量计的工作，要求被测介质必须是地电位，一般是通过管道或管道法兰接地，若连接传感器的工艺管道相对被测介质是绝缘的（塑料管道或有绝缘衬里的管道），就必须选用接地环或带接地电极的传感器，使被测介质处于地电位。 接地环的形式又分普通型和保护型，一般使用普通型，若被测介质是磨损性的，宜使用带颈的保护接地环，以保护进出口端的衬里，延长使用寿命。...