GB/T 16608.55-2012
Electromechanical all-or-nothing relays.Part 55:Blank detail specification.Electromechanical all-or-nothing telecom relays of assessed quality.Two change-over contacts,11mm×7.5mm base (English Version)

Standard No.

GB/T 16608.55-2012

Language

Chinese, Available in English version

Release Date

2012

Published By

General Administration of Quality Supervision, Inspection and Quarantine of the People‘s Republic of China

Status

Be replaced 2023-10

Replace By

GB/T 16608.1-2023

Latest

GB/T 16608.1-2023

Scope

This part of GB/T 16608 is a blank detail specification, applicable to electrical relays with or without quality assessment for telecommunications. Relays complying with this standard are intended for use in telecommunication equipment, but may also be used in specific industrial or other equipment as electrical or non-electrical relays. The test methods specified in this section are quoted from IEC 61810-7:1997 and other standards for use in detailed specifications developed in accordance with this specification. This part also specifies the basic inspection table for use in the detailed specifications formulated in accordance with the provisions of GB/T 16608.1-2003.

GB/T 16608.55-2012 Referenced Document

• GB/T 14598.4-1993 Electrical relays. Part 14: Endurance test for electrical relay contacts. Preferred values for contact loads
• GB/T 16608.1-2003 Electromechanical elementary all-or-nothing relays of assessed quality-Part 1:Generic specification
• GB/T 16608.50-2012 Electromechanical all-or-nothing relays.Part 50:Sectional specification.Electromechanical all-or-nothing telecom relays of assessed quality
• GB/T 2421-1999 Environmental testing for electric and electronic products Part 1: General and guidance
• GB/T 5169.5-1997 Fire hazard testing for electric and electronic products. Part 2: Test methods. Section 2: Needle-flame test
• IEC 60068-2-17:1994 Basic environmental testing procedures - Part 2: Tests - Test Q: Sealing
• IEC 60068-2-20:1979 Environmental testing. Part 2: Tests. Test T: Soldering
• IEC 60068-2-47:1999 Environmental testing - Part 2-47: Test methods - Mounting of components, equipment and other articles for vibration, impact and similar dynamic tests
• IEC 61709:1996 Electronic components - Reliability - Reference conditions for failure rates and stress models for conversion
• IEC 61810-7:1997 Electromechanical all-or-nothing relays - Part 7: Test and measurement procedures
• QC 001002-2-1998 IEC quality assessment system for electronic components (IECQ) - Rules of procedure - Part 2: Documentation
• QC 001002-3-1998 IEC quality assessment system for electronic components (IECQ) - Rules of procedure - Part 3: Approval procedures

GB/T 16608.55-2012 history

• 2023 GB/T 16608.1-2023 Basic electromechanical relays for telecommunications with qualification - Part 1: General specification and blank detail specification
• 2012 GB/T 16608.55-2012 Electromechanical all-or-nothing relays.Part 55:Blank detail specification.Electromechanical all-or-nothing telecom relays of assessed quality.Two change-over contacts,11mm×7.5mm base

GB/T 16608.55-2012 Electromechanical all-or-nothing relays.Part 55:Blank detail specification.Electromechanical all-or-nothing telecom relays of assessed quality.Two change-over contacts,11mm×7.5mm base was changed to GB/T 16608.1-2023 Basic electromechanical relays for telecommunications with qualification - Part 1: General specification and blank detail specification.

GB/T 16608.55-2012 -All Parts