07.120 标准查询与下载

GB/Z 44005.1-2024 纳米技术 黏土纳米材料 第1部分：层状黏土的特性及测量方法

Nanotechnology Clay Nanomaterials Part 1: Properties and Measurement Methods of Layered Clays

GB/Z 43998-2024 纳米技术 混合粉尘制造环境空气中纳米级炭黑和无定形二氧化硅浓度的测量方法

Nanotechnology - Method for measuring the concentration of nanoscale carbon black and amorphous silica in ambient air from mixed dust manufacturing

GB/Z 43684-2024 纳米技术 光栅的描述、测量和尺寸质量参数

Nanotechnology Description, measurement and dimensional quality parameters of gratings

GB/T 43196-2023 纳米技术 扫描电子显微术测量纳米颗粒粒度及形状分布

Nanotechnology Scanning Electron Microscopy to Measure Nanoparticle Size and Shape Distribution

GB/T 42732-2023 纳米技术 水相中无机纳米颗粒的尺寸分布和浓度测量 单颗粒电感耦合等离子体质谱法

Size Distribution and Concentration Measurement of Inorganic Nanoparticles in Aqueous Phases in Nanotechnology by Single Particle Inductively Coupled Plasma Mass Spectrometry

GB/T 42739-2023 纳米科技 术语 纳米酶

nanotechnology term nanozyme

GB/T 30544.12-2023 纳米科技 术语 第12部分：纳米科技中的量子现象

Nanotechnology Terminology Part 12: Quantum Phenomena in Nanotechnology

GB/T 30544.7-2023 纳米科技 术语 第7部分：纳米医学诊断和治疗

Nanotechnology Terminology Part 7: Nanomedicine Diagnosis and Therapy

GB/T 41212-2021 纳米技术 荧光素二乙酸酯法检测纳米颗粒诱导巨噬细胞产生的活性氧

本文件描述了如何用5 -(6)-氯甲基2 ',7 '二氯二氢-荧光素二乙酸酯(CM-H2DCF-DA)检测和评价RAW264.7 巨噬细胞暴露于纳米物体、纳米颗粒及其聚集体和团聚体后产生活性氧(ROS)的方法。 本文件适用于用24 孔板的检测。如果用其他孔板,需要调整样品用量并检验操作步骤的有效性以保证检测结果可信。

Nanotechnologies—5-(and 6)-Chloromethyl-2’,7’ Dichloro-dihydrofluorescein diacetate (CM-H2DCF-DA) assay for evaluating nanoparticle-induced intracellular reactive oxygen species (ROS) production in RAW 264.7 macrophage cell line

GB/T 41232.2-2021 纳米制造 关键控制特性 纳米储能 第2部分：纳米正极材料的密度测试

本文件描述了一种测试电储能器件中粉末状纳米正极材料密度的方法。 本文件包含术语和定义、样品制备的推荐方法、纳米正极材料性能测试的主要过程、数据分析与结果解释和实例分析等。 本文件适用于判断纳米正极材料的可用性及适用性。

Nanomanufacturing—Key control characteristics—Nano-enabled electrical energy storage—Part 2: Density measurement of cathode nanomaterials

T/ZSA 225-2024 高导热膜用石墨烯材料应用指南

本标准基于FMEA分析方法，梳理了石墨烯导热膜制备工艺流程，分析了导热膜对石墨烯材料的技术要求，阐述了石墨烯材料各技术指标对制膜工艺、膜性能的影响，给出了制膜的优化实践案例。 本标准适用于企业或科研机构在建立石墨烯材料的DFMEA和石墨烯导热膜的PFMEA时提供参考。

Practice guides of graphene materials used for high thermal conductivity films

ASTM E2859-11(2023) 使用原子力显微镜测量纳米粒子尺寸的标准指南

1.1  The purpose of this document is to provide guidance on the quantitative application of atomic force microscopy (AFM) to determine the size of nanoparticles2 deposited in dry form on flat substrates using height (z-displacement) measurement. Unlike electron microscopy, which provides a two-dimensional projection or a two-dimensional image of a sample, AFM provides a three-dimensional surface profile. While the lateral dimensions are influenced by the shape of the probe, displacement measurements can provide the height of nanoparticles with a high degree of accuracy and precision. If the particles are assumed to be spherical, the height measurement corresponds to the diameter of the particle. In this guide, procedures are described for dispersing gold nanoparticles on various surfaces such that they are suitable for imaging and height measurement via intermittent contact mode AFM. Generic procedures for AFM calibration and operation to make such measurements are then discussed. Finally, procedures for data analysis and reporting are addressed. The nanoparticles used to exemplify these procedures are National Institute of Standards and Technology (NIST) reference materials containing citrate-stabilized negatively charged gold nanoparticles in an aqueous solution. 1.2  The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Size Measurement of Nanoparticles Using Atomic Force Microscopy

ISO/DTS 12901-1:2023 纳米技术 — 应用于工程纳米材料的职业风险管理 — 第 1 部分：原则和方法

Nanotechnologies — Occupational risk management applied to engineered nanomaterials — Part 1: Principles and approaches

ISO/TS 10818:2023 纳米技术 含有纳米材料和纳米结构的纺织品 超疏水特性和耐久性评估

Nanotechnologies — Textiles containing nanomaterials and nanostructures — Superhydrophobic characteristics and durability assessment

ISO/PRF TS 10818:2023 纳米技术 含有纳米材料和纳米结构的纺织品 超疏水特性和耐久性评估

Nanotechnologies — Textiles containing nanomaterials and nanostructures — Superhydrophobic characteristics and durability assessment

BS ISO 19337:2023 纳米技术 用于体外测定评估纳米物体固有毒性的纳米物体工作悬浮液的特性

1   Scope This document describes the characteristics of working suspensions of nano-objects to be considered when conducting in vitro assays to evaluate inherent nano-object toxicity. In addition, the document identifies applicable measurement methods for these characteristics. This document is applicable to nano-objects, and their aggregates and agglomerates greater than 100 nm. This document intends to help clarify whether observed toxic effects come from tested nano-objects themselves or from uncontrolled sources.

Nanotechnologies. Characteristics of working suspensions of nano-objects for in vitro assays to evaluate inherent nano-object toxicity

IEC TS 62607-6-8:2023 纳米制造 关键控制特性 第 6-8 部分：石墨烯 方块电阻：串联四点探针

Nanomanufacturing - Key control characteristics - Part 6-8: Graphene - Sheet resistance: In-line four-point probe

IEC TS 62607-6-7:2023 纳米制造 关键控制特性 第 6-7 部分：石墨烯 薄层电阻：van der Pauw 方法

Nanomanufacturing - Key control characteristics - Part 6-7: Graphene - Sheet resistance: van der Pauw method

IEC TS 62565-5-1:2023 纳米制造 产品规格 第 5-1 部分：纳米多孔活性炭 空白详细规格：电化学电容器

Nanomanufacturing - Product specifications - Part 5-1: Nanoporous activated carbon - Blank detail specification: Electrochemical capacitors

IEC 62607-6-7:2023 纳米制造 关键控制特性 第 6-7 部分：石墨烯 方块电阻：范德堡法

Nanomanufacturing. Key control characteristics. - Part 6-7: Graphene. Sheet resistance: van der Pauw method