13.220.20 防火 标准查询与下载

22/30447464 DC BS EN 12845-3 固定消防系统 自动喷水灭火系统 第 3 部分：地震支撑指南

BS EN 12845-3. Fixed firefighting systems. Automatic sprinkler systems - Part 3. Guidance for earthquake bracing

T/IMAS 049-2022 灭火器维修管理规程

本文件规定了灭火器的维修条件、维修步骤、报废与回收、运输等技术要求。 本文件适用于干粉灭火器、二氧化碳灭火器、水基灭火器和洁净气体灭火器维修管理。

Code of practice for fire extinguisher maintenance management

ISO 7240-12:2022 火灾探测和报警系统.第12部分:使用透射光束的线型烟雾探测器

Fire detection and alarm systems — Part 12: Line type smoke detectors using a transmitted optical beam

22/30439190 DC BS EN 12259-12 固定消防系统 洒水装置和喷水系统部件 第 12 部分：泵

BS EN 12259-12. Fixed firefighting systems. Components for sprinkler and water spray systems - Part 12. Pumps

ANSI/CAN/UL/ULC 312:2022 消防用止回阀

1.1 These requirements cover check valves of 1 NPS and larger, used in piping systems supplying water for fire protection service. 1.2 The check valves covered by these requirements are intended for installation and use in accordance with the Standards for: a) Low-, Medium-, and High-Expansion Foam, NFPA 11; b) Installation of Sprinkler Systems, NFPA 13; c) Installation of Standpipe and Hose Systems, NFPA 14; d) Water Spray Fixed Systems for Fire Protection, NFPA 15; e) Installation of Foam-Water Sprinkler and Foam-Water Spray Systems, NFPA 16; f) Installation of Stationary Pumps For Fire Protection, NFPA 20; g) Water Tanks for Private Fire Protection, NFPA 22; h) Installation of Private Fire Service Mains and Their Appurtenances, NFPA 24; i) Water Mist Fire Protection Systems, NFPA 750; and j) Installation of Sprinkler Systems in Residential Occupancies Up to and Including Four Stories in Height, NFPA 13R. 1.3 Check valves covered by these requirements are intended for installation and use in accordance with, but not limited to the National Fire Code of Canada (NFC), and the National Building Code of Canada (NBC).

Check Valves for Fire-Protection Service

GSO ISO 21927-8:2022 烟雾和热量控制系统 第8部分：烟雾控制风阀

ISO 21927-8:2017 applies to smoke control dampers, placed on the market and intended to operate as part of a pressure differential system or smoke and heat control system. This document specifies requirements and gives reference to the test methods defined for smoke control dampers and their associated components, such as actuators which are intended to be installed in such systems in buildings. Furthermore, provision on marking and information on installation and maintenance of these products are also given. ISO 21927-8:2017 distinguishes between two categories of smoke control dampers, i.e. single-compartment smoke control dampers and multi‑compartment fire-resisting smoke control dampers. Smoke control dampers covered by this document can be installed into smoke control system ducts or onto the ducts' surface. They can be installed also into a wall, floor or ceiling/roof elements or onto the surface of these elements. NOTE To avoid duplication, reference is made to a variety of other standards. To this end, this document can be read in conjunction with EN 13501‑4, EN 1366‑10 and ISO 10294‑1 for details of the furnace testing. ISO 21927-8:2017 does not consider in detail the detrimental and/or corrosive effects that can be caused by process chemicals present in the atmosphere, which are drawn through the system intentionally or inadvertently.

Smoke and heat control systems — Part 8: Smoke control dampers

GSO ISO 21927-5:2022 烟雾和热量控制系统 第5部分：动力排烟系统 要求和设计

This document applies to powered smoke exhaust systems in spaces with a large area and with a ceiling height of minimum 3 m, in which smoke protection is required. It includes tables and calculation methods for the design of clear layers in order to comply, inter alia, with the requirements of various protection objectives. This document includes information and provisions concerning the requirements for powered smoke exhaust systems, their design and rules for their installation. NOTE The requirements for testing the ventilators are dealt with in ISO 21927‑3. Other parts of the ISO 21927 series of standards deal with the power supply (ISO 21927‑10), control equipment (ISO 21927‑9) and smoke control ducts and smoke control dampers (ISO 21927‑7 and ISO 21927-8 respectively). Design, as specified in this document, does not apply to: — spaces with fixed gas extinguishing systems; — storage facilities for hazardous materials; — spaces in which there is a risk of explosions; — corridors; — stairwells.

Smoke and heat control systems — Part 5: Powered smoke exhaust systems — Requirements and design

GSO ISO 7240-5:2022 火灾探测和火灾报警系统 第5部分：点型热探测器

ISO 7240-5:2018 specifies the requirements, test methods and performance criteria for point type heat detectors for use in fire detection and fire alarm systems for buildings (see ISO 7240‑1). For other types of heat detector, or for detectors intended for use in other environments, this document can be used for guidance only. Heat detectors with special characteristics and developed for specific risks are not covered by this document.

Fire detection and fire alarm systems — Part 5: Point type heat detectors

GSO ISO 7240-2:2022 火灾探测和报警系统 第2部分：火灾探测控制和指示设备

ISO 7240-2:2017 specifies requirements, test methods and performance criteria for fire detection control and indicating equipment (FDCIE) for use in fire detection and fire alarm systems installed in buildings. For the testing of other types of FDCIE, this document is intended to be used only for guidance. FDCIE with special characteristics, developed for specific risks, are not covered in ISO 7240-2:2017.

Fire detection and alarm systems — Part 2: Fire detection control and indicating equipment

GSO ISO 6182-12:2022 消防 自动喷水灭火系统 第12部分：钢管系统沟槽端部件的要求和试验方法

This document specifies performance requirements, grooving dimensions, test methods and marking requirements for couplings used in the joining of grooved steel tubes, pipes, grooved-end fittings and other grooved-end components up to 300 DN nominal diameter.

Fire protection — Automatic sprinkler systems — Part 12: Requirements and test methods for grooved-end components for steel pipe systems

T/STSI 32-2022 防冻地上消防栓技术规范

1 术语和定义 2 产品结构和参数 3 一般要求 4 技术要求 5 试验方法 6 标志、包装、运输、贮存

Technical specification for anti freezing aboveground fire hydrants

GSO ISO 6182-11:2022 消防 自动喷水灭火系统 第11部分：管道吊架的要求和试验方法

This document specifies construction requirements, performance requirements, test methods and marking requirements for typical types of pipe hangers.

Fire protection — Automatic sprinkler systems — Part 11: Requirements and test methods for pipe hangers

T/STSI 33-2022 防撞地上消防栓技术规范

1 术语和定义 2 产品结构和参数 3一般要求 4 技术要求 5 试验方法 6标志、包装、运输和贮存

Technical specification for anti-collision aboveground fire hydrants

GSO ISO 21927-7:2022 烟雾和热量控制系统 第7部分：烟雾管道部分

ISO 21927-7:2017 applies to smoke control duct sections placed on the market and intended to operate as part of a pressure differential system or smoke and heat exhaust system. This document specifies requirements and gives reference to the test methods defined for smoke control duct sections and their associated components (for example, hangers and other items proven at the time of testing), which are intended to be installed in such systems in buildings. Furthermore, marking and information on installation and maintenance of these products are also given in this document. NOTE To avoid duplication, reference is made to a variety of other standards. To this end, this document can be read in conjunction with EN 1366‑8, EN 1366‑9 and ISO 6944‑1, for details of the fire resistance testing and EN 13501‑4 for corresponding classification. ISO 21927-7:2017 has not considered in detail the detrimental and/or corrosive effects that may be caused by process chemicals present in the atmosphere, which are drawn through the system intentionally or inadvertently. ISO 21927-7:2017 also governs associated components used together with smoke control duct sections such as turning vanes and silencers, with the exception of natural and powered smoke ventilators and smoke control dampers, which are covered by separate standards. Ducts for use other than in smoke and heat exhaust/control systems are not covered by this document.

Smoke and heat control systems — Part 7: Smoke ducts sections

T/STSI 34-2022 防漏地上消防栓技术规范

1 术语和定义 2 产品结构和参数 3 一般要求 4技术要求 5 试验方法 6标志、包装、运输和贮存

Technical specification for leak proof aboveground fire hydrants

GSO ISO 7240-4:2022 火灾探测和报警系统 第4部分：供电设备

ISO 7240-4:2017 specifies requirements, test methods and performance criteria for power supply equipment (PSE) for use in fire detection and alarm systems installed in buildings. For the testing of other types of the PSE, this document is intended to be used only for guidance. The PSE with special characteristics, developed for specific risks, are not covered in ISO 7240-4:2017.

Fire detection and alarm systems — Part 4: Power supply equipment

GSO ISO 6182-14:2022 消防 自动喷嘴系统 第14部分：喷水喷嘴的要求和试验方法

This document specifies performance requirements, methods of test, and marking requirements for open water spray nozzles. This document is not applicable to open sprinklers or open water mist nozzles. Factors of installation, such as nozzle spacing, design densities, wind and hot gas velocities, are not intended to be addressed by this document.

Fire protection — Automatic nozzle systems — Part 14: Requirements and test methods for water spray nozzles

ISO/TR 7240-9:2022 火灾探测和报警系统.第9部分:火灾探测器的试验火

Fire detection and alarm systems — Part 9: Test fires for fire detectors

T/STIC 120062-2022 基于大数据分析的消防安全管理数据服务要求

本文件规定了消防物联网系统数据服务商提供基于大数据分析的消防安全管理数据服务活动相关的服务、管理以及评价要求。 本文件适用于消防物联网系统数据服务商规范其服务活动和自我评价，也适用于认证机构及相关方开展第三方认证及符合性评价活动。

Data service requirements for administration of fire safety based on big data analytics

T/SA 47-2022 消防用智能洒水喷头技术规范

1 术语和定义 2 总体要求 3 试验方法 4 标志、包装、运输和贮存。

Technical Specification for intelligent sprinkler heads for fire protection