13.220.40;83.080.01 标准查询与下载

BS EN ISO 4589-3:1996 塑料.通过氧指数测定其燃烧性.第3部分:高温试验

This part of ISO 4589 specifies methods for deter-mining the minimum concentration of oxygen, in a mixture with nitrogen, that will support combustion of small vertical test specimens under specified test conditions over a range of temperatures typically be-tween 25 ℃ and 150 ℃. The results are defined as oxygen index values at the test temperature, which is typical of the practical temperature that a plastic ma-terial may experience in an overheated service situ-ation. Methods are provided for testing materials that are self-supporting at the test temperature in the form of vertical bars or sheet up to 10,5 mm thick. These methods are suitable for solid, laminated or cellular materials characterized by an apparent density greater than 100 kg/m. The methods may also be applicable to some cellular materials having an apparent density of less than 100 kg/m. A method is provided for testing flexible sheet or film materials while supported vertically. This part of ISO 4589 also includes a method (see annex A) for determining the temperature at which the oxygen index of small vertical test specimens in air is 20,9 under specified test conditions. The result is defined as the flammability temperature (FT) and the method is limited to the determination of results less than 400 ℃. The method is not applicable to materials having an oxygen index of < 20,9 when measured at 23 ℃. Results obtained in accordance with this part of ISO 4589 should not be used to describe or appraise the fire hazard presented by a particular material or shape under actual fire conditions, unless used as one element of a fire risk assessment which takes into account all of the factors which are pertinent to the assessment of the fire hazard of a particular applica-tion for the material. NOTES 1 It may not be possible to apply these methods satisfac-torily to materials that exhibit high levels of shrinkage when heated, e.g. highly oriented thin film. 2 For assessing the flame propagation properties of cellu-lar materials of density < 100 kg/m, attention is drawn to the method of ISO 3582:1978, Cellular plastic and cellular rubber materials ?Laboratory assessment of horizontal burning characteristics of small specimens subjected to a small flame.

Plastics. Determination of burning behaviour by oxygen index. Elevated temperature test

ISO 4589-1:1996 塑料 通过氧指数测定其燃烧性 第1部分:指南

Guidance document for the determination of burning behaviour of plastics by the oxygen index (OI). Provides information to guide the reader in the use of the test procedures described in parts 2 and 3.

Plastics - Determination of burning behaviour by oxygen index - Part 1: Guidance

NF T51-071-3:1996 塑料制品.用氧指数测定燃烧性能.第3部分:高温试验

Plastics. Determination of burning behaviour by oxygen index. Part 3 : elevated-temperature test.

UL 94-1996 设备和器具部件用塑料材料易燃性的试验

UL is issuing a Recirculation Proposal to address comments received on the previous UL 94 Proposal dated October 14, 2005. These proposals affect paragraphs 1.2.1, 2.2.1, 5.1, 6.3, 11.1.1, and 11.1.1.1.

Test for flammability of plastic materials for parts in devices and appliances

BS EN ISO 5659-1:1996 塑料 烟雾产生 第1部分：光密度试验的导则ISO 5659-1-1996

Plastics. Smoke generation. Guidance on optical-density testing

DIN EN ISO 4589-3:1996 塑料.通过氧指数测定塑料燃烧性.第3部分:高温试验

The document specifies methods for determining the minimum concentration of oxygen, in admixture with nitrogen, that will support combustion of small vertical test specimens under specified test conditions over a range of temperature typically between 25 ?and 150 ?

Plastics - Determination of burning behaviour by oxygen index - Part 3: Elevated-temperature test (ISO 4589-3:1996); German version EN ISO 4589-3:1996

ISO 871:1996 塑料 用热风炉测定点燃温度

Gives a laboratory method for determining the flash-ignition temperature and spontaneous-ignition temperature of plastics using a hot-air furnace. Does not give a direct measure of the combustability or rate of burning of plastics. Replaces the first edition.

Plastics - Determination of ignition temperature using a hot-air furnace

EN ISO 4589-3:1996 塑料.燃烧行为的氧指数测定.第3部分:高温试验 ISO 4589-3-1996

Plastics - Determination of Burning Behaviour by Oxygen Index - Part 3: Elevated-Temperature Test ISO 4589-3: 1996

ISO 4589-3:1996 塑料 通过氧指数测定其燃烧性 第3部分:高温试验

Specifies methods for the determination the minimum concentration of oxygen, in a mixture with nitrogen, that will support combustion of small vertical test specimens under specified test conditions over a range of temperatures between 25 鳦elsius and 150 鳦elsius. The results are defined as oxygen index values at the test temperature. Also included is a method for determining the flammability temperature (less than 400 鳦elsius) at which the oxygen index of small vertical test specimens in air is 20,9.

Plastics - Determination of burning behaviour by oxygen index - Part 3: Elevated-temperature test

ISO 4589-2:1996 塑料 通过氧指数测定其燃烧性 第2部分:室温试验

This part of ISO 4589 specifies methods for deter-mining the minimum concentration of oxygen, in ad-mixture with nitrogen, that will support combustion of small vertical test specimens under specified test conditions. The results are defined as oxygen index values. Methods are provided for testing materials that are self-supporting in the form of vertical bars or sheet up to 10,5 mm thick. These methods are suitable for solid, laminated or cellular materials characterized by an apparent density greater than 100 kg/m. The methods may also be applicable to some cellular ma-terials having an apparent density of less than 100 kg/m. A method is provided for testing flexible sheet or film materials while supported vertically. For comparative purposes, a procedure is provided for determining whether or not the oxygen index of a material lies above some specified minimum value. Oxygen index results obtained using the methods described in this part of ISO 4589 can provide a sen-sitive measure of the burning characteristics of ma-terials under certain controlled laboratory conditions, and hence may be useful for quality control purposes. The results obtained are dependent upon the shape, orientation and isolation of the test specimen and the conditions of ignition. For particular materials or appli-cations, it may be necessary or appropriate to specify different test conditions. Results obtained from test specimens of differing thickness or by using different ignition procedures may not be comparable and no correlation with flammability behaviour under other fire conditions is implied. Results obtained in accordance with this part of ISO 4589-2 must not be used to describe or appraise the fire hazard presented by a particular material or shape under actual fire conditions, unless used as one element of a fire risk assessment that takes into ac-count all of the factors pertinent to the assessment of the fire hazard of a particular application for the material. NOTES 1 It may not be possible to apply these methods satisfac-torily to materials that exhibit high levels of shrinkage when heated, e.g. highly oriented thin film. 2 For assessing the flame propagation properties of cellu-lar materials of density < 100 kg/m, attention is drawn to the method of ISO 3582:1978, Cellular plastic and cellular rubber materials — Laboratory assessment of horizontal burning characteristics of small specimens subjected to a small flame, for testing horizontal burning characteristics.

Plastics - Determination of burning behaviour by oxygen index - Part 2: Ambient-temperature test

BS ISO 12992:1995 塑料制品.薄膜和薄板垂直火焰蔓延的测定

This International Standard specifies a test method for the measurement of flame spread properties of verti-cally oriented specimens of plastics in the form of film and sheet, 3 mm or less in thickness, subjected to a small igniting flame.

Plastics - Vertical flame spread determination for film and sheet

BS ISO 12992:1996 塑料制品 薄膜和薄板垂直火焰蔓延的测定

Plastics. Vertical flame spread determination for film and sheet

ISO 5659-1:1996 塑料 烟雾产生 第1部分:光密度测定指南

Part 1 constitutes the guidance document of ISO 5659 for the test procedure described in part 2.

Plastics - Smoke generation - Part 1: Guidance on optical-densitiy testing

BS ISO 11907-2:1996 塑料制品.烟雾生成.火灾流出物腐蚀性的测定.第2部分:静态法

Describes a test method using a small-scale laboratory apparatus for the determination of the corrosive effects of combustion products liberated by burning plastics. Makes it possible to produce a ranking of materials by corrosivity of their combustion products under specific test conditions with regard to combustion temperature, available oxygen, ventilation and different humidity levels.

Plastics - Smoke generation - Determination of the corrosivity of fire effluents - Static method

ASTM D1929-96(2001)e1 塑料引燃性能的标准试验方法

Tests made under conditions herein prescribed can be of considerable value in comparing the relative ignition characteristics of different materials. Values obtained represent the lowest ambient air temperature that will cause ignition of the material under the conditions of this test. Test values are expected to rank materials according to ignition susceptibility under actual use conditions. This test is not intended to be the sole criterion for fire hazard. In addition to ignition temperatures, fire hazards include other factors such as burning rate or flame spread, intensity of burning, fuel contribution, products of combustion, and others.1.1 This fire test response test methodsup2 covers a laboratory determination of the flash ignition temperature and spontaneous ignition temperature of plastics using a hot-air furnace. 1.2 Caution-During the course of combustion, gases or vapors, or both, are evolved that may be hazardous to personnel. Adequate precautions should be taken to protect the operator. 1.3 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazards or fire risk assessment of materials, products, or assemblies under actual fire conditions. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 1.2 and 1.4. Note 1- This test method and ISO 871-1996 are identical in all technical details.

Standard Test Method for Determining Ignition Temperature of Plastics

ANSI/ASTM D1929:1996 塑料燃点特性测试方法(08.01)

This fire test response test method covers a laboratory determination of the flash ignition temperature and spontaneous ignition temperature of plastics using a hot-air furnace. Caution-During the course of combustion, gases or vapors, or both, are evolved that may be hazardous to personnel. Adequate precautions should be taken to protect the operator. This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazards or fire risk assessment of materials, products, or assemblies under actual fire conditions. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 1.2 and 1.4. Note 1- This test method and ISO 871-1996 are identical in all technical details.

Test Method for Ignition Properties of Plastics (08.01)

ISO 11907-2:1995 塑料 烟雾产生 火焰效应腐蚀性的测定 第2部分:静态法

Describes a test method using a small-scale laboratory apparatus for the determination of the corrosive effects of combustion products liberated by burning plastics. Makes it possible to produce a ranking of materials by corrosivity of their combustion products under specific test conditions with regard to combustion temperature, available oxygen, ventilation and different humidity levels.

Plastics - Smoke generation - Determination of the corrosivity of fire effluents - Part 2: Static method

ISO 12992:1995 塑料 塑料薄膜和薄板垂直燃烧蔓延程度的测定

Deals with a test method for the measurement of flame spread properties of vertically oriented specimens of plastics in the form of film and sheet, 3 mm or less in thickness, subjected to a small igniting flame.

Plastics - Vertical flame spread determination for film and sheet

BS 2782-1 Method 140A:1992 塑料测试方法 热性能 水平和垂直样品与小火焰点火源接触的燃烧行为的测定

To be read in conjunction with BS 2782-0

Methods of testing plastics. Thermal properties. Determination of the burning behaviour of horizontal and vertical specimens in contact with a small-flame ignition source

DIN 54836:1984 可燃材料试验.点燃温度测定

Testing of combustible materials; determination of ignition temperature

Testing of combustible materials; determination of ignition temperature