13.340.50 防护鞋 标准查询与下载
共找到 493 条与 防护鞋 相关的标准，共 33 页
1.1 These test methods measure the resistance of footwear to a variety of hazards that can potentially result in injury. 1.2 These test methods may be used to test for compliance to minimum performance requirements in established safety standards. 1.2.1 By agreement between the purchaser and the supplier, or as required by established safety standards, these test methods can be used to determine any one, or all of the following: (1) impact resistance (I), (2) compression resistance (C), (3) metatarsal impact resistance (Mt), (4) resistance to electrical conductivity (Cd), (5) resistance to electric hazard (EH), (6) static dissipative performance (SD), and (7) puncture resistance (PR). 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Test Methods for Foot Protection
- ICS
- 13.340.50
- CCS
- 发布
- 2018-08-01
- 实施
本标准规定了非湿度依赖型防静电鞋的功能原理、技术指标及检测方法、检验规则、标识、包装、运输、贮存的要求。 本标准适用于在电子、半导体、医药、食品等领域使用的能消除人体静电积聚的各类鞋。本标准规定的防静电鞋不适用于抗电源电压。
Non-humidity Reliant Anti-static Shoes
- ICS
- 13.340.50
- CCS
- C183
- 发布
- 2018-07-23
- 实施
- 2018-07-24
Standard Test Methods for Foot Protection
- ICS
- 13.340.50
- CCS
- 发布
- 2018-02-01
- 实施
1 Scope This document provides the principles that govern the development of incident type and/or hazard specific test methods and minimum performance requirements for safety footwear for firefighters while engaged in specific rescue activities. Footwear related to specific rescue activities, e.g. Road Traffic Crash, (RTC) and Urban Search and Rescue, (USAR) is documented in individual subclauses of this document. NOTE For further guidance refer ISO 18639‑1. The purpose of this document is to ensure minimum performance requirements for incident type and/or hazard specific safety footwear are designated. This document covers general footwear design, the minimum performance level of the materials used and the methods of test for determining this performance level. It does not cover special footwear for use in other high risk situations such as structural firefighting. This document does not cover protection for the head, torso, arms, hands and legs or protection of the feet against other hazards, e.g. chemical, biological, radiation and electrical hazards, except for limited, accidental exposure to fire ground chemicals and contaminated blood or body fluids. Selection of the appropriate system of Personal Protective Equipment, (PPE), including footwear, is dependent on carrying out an effective risk assessment which identifies the hazard to be faced, evaluates the likelihood of those hazards and provides the means of reducing or eliminating these hazards.
PPE ensembles for firefighters undertaking specific rescue activities - Footwear
- ICS
- 13.340.50
- CCS
- 发布
- 2018-01-31
- 实施
- 2018-01-31
This document provides the principles that govern the development of incident type and/or hazard specific test methods and minimum performance requirements for safety footwear for firefighters while engaged in specific rescue activities. Footwear related to specific rescue activities, e.g. Road Traffic Crash, (RTC) and Urban Search and Rescue, (USAR) is documented in individual subclauses of this document. NOTE For further guidance refer ISO 18639-1. The purpose of this document is to ensure minimum performance requirements for incident type and/or hazard specific safety footwear are designated. This document covers general footwear design, the minimum performance level of the materials used and the methods of test for determining this performance level. It does not cover special footwear for use in other high risk situations such as structural firefighting. This document does not cover protection for the head, torso, arms, hands and legs or protection of the feet against other hazards, e.g. chemical, biological, radiation and electrical hazards, except for limited, accidental exposure to fire ground chemicals and contaminated blood or body fluids. Selection of the appropriate system of Personal Protective Equipment, (PPE), including footwear, is dependent on carrying out an effective risk assessment which identifies the hazard to be faced, evaluates the likelihood of those hazards and provides the means of reducing or eliminating these hazards.
PPE ensembles for firefighters undertaking specific rescue activities — Part 6: Footwear
- ICS
- 13.340.50
- CCS
- 发布
- 2018-01-05
- 实施
Protective footwear for motorcycle riders - Requirements and test methods
- ICS
- 13.340.50
- CCS
- 发布
- 2017-12-01
- 实施
This document specifies additional requirements and test methods for hand and foot protectors which are used in unarmed martial arts, including boxing, for strikes against other persons or training equipment.
Protective equipment for martial arts — Part 7: Additional requirements and test methods for hand and foot protectors
- ICS
- 13.340.50
- CCS
- 发布
- 2017-11-29
- 实施
Personal protective equipment. Footwear protecting against risks in foundries and welding. Requirements and test methods for protection against risks in foundries
- ICS
- 13.340.50
- CCS
- 发布
- 2017-11-29
- 实施
- 2017-11-30
This document specifies additional requirements and test methods for instep protectors, shin protectors and forearm protectors used in unarmed martial arts such as taekwondo, karate, kick- boxing and similar disciplines. For general requirements and test methods for protective equipment for martial arts, see ISO 21924-1.
Protective equipment for martial arts — Part 2: Additional requirements and test methods for instep protectors, shin protectors and forearm protectors
- ICS
- 13.340.50
- CCS
- 发布
- 2017-11-29
- 实施
Standard Specification for Performance Requirements for Protective (Safety) Toe Cap Footwear
- ICS
- 13.340.50
- CCS
- 发布
- 2017-11-01
- 实施
Standard Specification for Performance Requirements for Soft Toe Protective Footwear (Non-Safety / Non-Protective Toe)
- ICS
- 13.340.50
- CCS
- 发布
- 2017-11-01
- 实施
Personal protective equipment - Footwear protecting against risks in foundries and welding. Part 2: Requirements and test methods for protection against risks in welding and allied processes (ISO 20349-2:2017)
- ICS
- 13.340.50
- CCS
- 发布
- 2017-09-27
- 实施
- 2017-09-30
Personal protective equipment - Footwear protecting against risks in foundries and welding - Part 2: Requirements and test methods for protection against risks in welding and allied processes
- ICS
- 13.340.50
- CCS
- 发布
- 2017-09-01
- 实施
BS EN 13832-3. Footwear protecting against chemicals - Part 3. Requirements for prolonged contact with chemicals
- ICS
- 13.340.50
- CCS
- 发布
- 2017-08-08
- 实施
- 2017-08-08
This document specifies requirements and test methods for footwear protecting users against risks, such as those encountered in welding and allied process. Footwear complying with this document also offers other protection as defined in ISO 20345.
Personal protective equipment — Footwear protecting against risks in foundries and welding — Part 2: Requirements and test methods for protection against risks in welding and allied processes
- ICS
- 13.340.50
- CCS
- 发布
- 2017-08-07
- 实施
Personal protective equipment - Footwear protecting against risks in foundries and welding - Part 1: Requirements and test methods for protection against risks in foundries
- ICS
- 13.340.50
- CCS
- 发布
- 2017-08-01
- 实施
This document specifies requirements and test methods for footwear protecting users against risks, such as those encountered in foundries. Footwear complying with this document also offers other protection as defined in ISO 20345. NOTE Gaiters over boot and clothing intended to provide protection to the feet and legs against molten metal are addressed by ISO 11612.
Personal protective equipment - Footwear protecting against risks in foundries and welding - Part 1: Requirements and test methods for protection against risks in foundries
- ICS
- 13.340.50
- CCS
- 发布
- 2017-07-00
- 实施
Occupational safety standards system. Special footwear, resistant to chain saw cutting. Technical requirements
- ICS
- 13.340.50
- CCS
- 发布
- 2017-00-00
- 实施
- 2018-07-01
Occupational safety standards system. Feet personal protective means. Safety footwear. Test method for slip resistance
- ICS
- 13.340.50
- CCS
- 发布
- 2017-00-00
- 实施
- 2018-07-01
Guidance for the selection, use and maintenance of safety,protective and occupational footwear
- ICS
- 13.340.50
- CCS
- 发布
- 2016-12-28
- 实施
