17.040.10 极限和配合 标准查询与下载

ISO/FDIS 13920 焊接 “焊接结构的一般公差” “长度和角度的尺寸” “形状和位置”

Welding — General tolerances for welded constructions — Dimensions for lengths and angles — Shape and position

CAN/CSA-Z10079-2003 医用抽吸设备 第1部分：电动抽吸设备 安全要求（第一版）

Medical suction equipment - Part 1: Electrically powered suction equipment - Safety requirements (First Edition)

GSO ISO 286-2:2002 国际限制和兼容性系统 第2部分：孔和轴的标准公差和极限偏差表

This standard gives values of the limit deviations for commonly used tolerance classes (zones) for holes and shafts calculated from the information given in part 1 . This standard covers values for the upper deviations ES (for holes) and es (for shafts), and the lower deviations EI (for holes) and ei (for shafts) (see figure 1). Note- In the tables of limit deviations, the values for the upper deviation ES or es are shown above the values for the values for the lower deviation EI or en except for tolerance class JS and js which is symmetrical about the zero line.

ISO system of limits and fits -- Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts

GOST 30893.1-2002 互换性的基本规范.一般容差.无容差标记的线性和角向尺寸的限制偏差

Basic norms of interchangeability. General tolerances. Limit deviations for linear and angular dimensions without tolerance indications

GOST 30893.2-2002 互换性的基本规范.一般容差.无单个容差标记的特征形状和位置容差

Basic norms of interchangeability. General tolerances. Tolerances of form and position for features without individual tolerance indications

KS B 0435-2001 自由锻件的机械加工余度

이 규격은 해머 및 프레스에 의한 타격 질량이 10 kg을 초과하고, 10 t 이하의 탄소

Machining allowance for open die forgings

LST EN 22768-2-2001 一般公差 第2部分：无单独公差指示的特征的几何公差（ISO 2768-2:1989）

General tolerances - Part 2: Geometrical tolerances for features without individual tolerance indications (ISO 2768-2:1989)

LST EN ISO 14253-1:2001 几何产品规范（GPS） 通过测量工件和测量设备进行检验 第1部分：证明符合或不符合规范的判定规则（ISO 14253-1:1998）

Geometrical Product Specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 1: Decision rules for proving conformance or non-conformance with specifications (ISO 14253-1:1998)

LST EN 22768-1-2001 一般公差 第1部分：无单独公差指示的线性和角度尺寸的公差（ISO 2768-1:1989）

General tolerances - Part 1: Tolerances for linear and angular dimensions without individual tolerance indications (ISO 2768-1:1989)

AS 4826.1:2001 几何产品的规范．通过工件尺寸测量和设备测量进行检验

Establishes rules for determining when the characteristics of a workpiece or measuring equipment are in conformance or non-conformance with a given tolerance for a workpiece or limits of maximum permissible errors for measuring equipment. This Standard i

Geometric Product Specifications (GPS) - Inspection by measurement of workpieces and measuring equipment

NF E02-353:2001 几何产品规范(GPS).梯形齿部件.无特殊公差指示的尺寸和零件的尺寸和表面平整公差

Geometrical products specification (GPS) - Chased parts - Dimensional and surface eveness tolerances for dimensions and parts without individual tolerances.

KS B 0250-2000(2020)(英文版) 铸件尺寸公差和加工余量系统

Castings-System of dimensional tolerances and machining allowances

KS B 0250-2000 铸件.尺寸公差及切削余度规定

이 규격은 주조품의 치수 공차 및 요구하는 절삭 여유 방식에 대하여 규정하고, 금속 및 합

Castings-System of dimensional tolerances and machining allowances

KS B 0412-2000(2005) 一般公差第1部分无单独公差指示的线性和角度尺寸公差

General tolerances-Part 1：Tolerances for linear and angular dimensions without individual tolerance indications

KS B 0250-2000(2020) 铸件 - 尺寸公差和加工余量系统

Castings-System of dimensional tolerances and machining allowances

GSO ISO 370:2000 将具有公差的尺寸从英寸转换为毫米 反之亦然

This Gulf standard specifies methods of conversion of tolerance dimensions from inches into millimetres and vice versa, which ensure, under the most suitable conditions, practical regard for interchangeability corresponding to the specified tolerances.

Toleranced dimensions -- Conversion from inches into millimetres and vice versa

KS B 0516-2000 棱镜上的角度和斜率

ANGLES AND SLOPES ON PRISM

NF E10-108:2000 尺寸测量方法.第9部分:位置偏差

Dimensional measuring methods - Part 9 : positioning deviation.

KS B 5634-1999 棱体的角度与斜度

이 규격은 기계에 사용하는 프리즘 각도 및 프리즘 구배의 기준값에 대하여 규정한다.

Angles and slopes on prisms

NF E02-352:1999 几何产品规范(GPS).切割和弯曲的工件.无特殊公差指示的尺寸和部件的尺寸和几何公差

Geometrical product specifications (GPS). Cutted and bended workpieces. Dimensional and geometrical tolerances for dimensions and features without individual tolerances.