17.120.20 明渠中流量的测量 标准查询与下载

KS B ISO 23350-2023 水文测量——捕捉式液体降水量计

Hydrometry — Catching-type liquid precipitation measuring gauges

KS B ISO 9826-2023 明渠液体流量的测量Parshall和SANIIRI水槽

Measurement of liquid flow in open channels — Parshall and SANIIRI flumes

KS B ISO 24578-2023 水文测量声学多普勒剖面仪测量移动船只明渠流量的方法和应用

Hydrometry — Acoustic Doppler profiler — Method and application for measurement of flow in open channels from a moving boat

BS EN 17694-2:2023 水文测量 水监测设备的最低性能要求和测试程序 流量测定装置 闭式导管仪表

1   Scope This document specifies general requirements, minimum performance requirements and test procedures for instrumentation used to measure either volumetric flow-rate and/or total volume passed of water in closed conduits . It covers all closed conduit instrument ( CCI ) technologies intended to operate in closed pressurized pipes and partially filled pipes. Requirements are expressed in volumetric units which may be converted to mass using the density of the water. It is recognized that for some CCIs certain tests cannot be carried out. The data obtained from the testing of CCIs in accordance with the requirements of the Measuring Instruments Directive [1] or EN ISO 4064‑1 [2] can be used to meet, in part, the requirements specified in this document. However, for the avoidance of doubt, compliance with the requirements of this document does not equate to compliance with the requirements of the Measuring Instruments Directive or EN ISO 4064‑1.

Hydrometry. Minimum performance requirements and test procedures for water monitoring equipment. Devices for the determination of flow - Closed conduit instrumentation

T/CAEPI 67-2023 《便携式（磁致伸缩）明渠流量计技术要求》

本标准规定了便携式（磁致伸缩）明渠流量计的基本要求、技术要求、检验方法、检验规则及标志、包装、运输和贮存。

Technical Requirements for Portable (Magnetostrictive) Open Channel Flowmeters

ISO/DIS 6640:2023 辐射透射法测量水沙混合物的密度

Measurement of density of water-sediment mixture using radiation transmission method

23/30441978 DC BS ISO 19234 水文测量 低成本挡板可帮助鱼在三角形轮廓测量堰上通过

BS ISO 19234. Hydrometry. Low cost baffles to aid fish passage on triangular profile gauging weirs

BS EN ISO 25377:2022 水文测量不确定度指南（HUG）

1   Scope This document provides an understanding of the nature of measurement uncertainty and its significance in estimating the "quality" of a measurement or a determination in hydrometry. This document is applicable to flow measurements in natural and man-made channels. Rainfall measurements are not covered.

Hydrometric uncertainty guidance (HUG)

BS ISO 4359:2022 流量测量结构 矩形、梯形、U形水槽

1   Scope This document specifies methods for the measurement of flow in rivers and artificial channels under steady or slowly varying flow conditions, using certain types of critical-depth flumes (also known as “standing-wave flumes”). A wide variety of flumes has been developed, but only those critical-depth flumes which have received general acceptance after adequate research and field testing, and which therefore do not require in situ calibration, are considered herein. The flow conditions considered are uniquely dependent on the upstream head, i.e. subcritical flow must exist upstream of the flume, after which the flow accelerates through the contraction and passes through its critical depth (see Figure 1). The water level downstream of the structure is low enough to have no influence upon its performance. This document is applicable to three commonly used types of flumes, covering a wide range of applications, namely rectangular-throated, trapezoidal-throated and U-throated. The hydraulic theory behind this document was presented in Reference [7]. This document is not applicable to a form of flume referred to in the literature (sometimes called a “Venturi” flume) in which the flow remains subcritical throughout. NOTE The Venturi form of flume is based on the same principle as a Venturi meter used within a closed conduit system and relies upon gauging the head at two locations and the application of Bernoulli’s energy formula.

Flow measurement structures. Rectangular, trapezoidal and U-shaped flumes

ASTM D3154-14(2023) 管道中平均速度的标准试验方法（皮托管法）

1.1 This test method describes measurement of the average velocity of a gas stream for the purpose of determining gas flow in a stack, duct, or flue. Although technically complex, it is generally considered the most accurate and often the only practical test method for taking velocity measurements. 1.2 This test method is suitable for measuring gas velocities above 3 m/s (10 ft/s). 1.3 This test method provides procedures for determining stack gas composition and moisture content. 1.4 The values stated in SI units are to be regarded as standard. The inch-pound units given in parentheses are for information only. 1.5 This test method is applicable to conditions where steady-state flow occurs, and for constant fluid conditions, where the direction of flow is normal to the face tube opening of the pitot tube employed in the method. The method cannot be used for direct measurement when cyclonic or swirling flow conditions are present. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Average Velocity in a Duct (Pitot Tube Method)

KS B ISO 4360-2022 水文测量.使用三角形断面堰测量明渠流量

Hydrometry — Open channel flow measurement using triangular profile weirs

KS B ISO 1438:2022 水文测量.用薄板堰测量明渠流量

Hydrometry — Open channel flow measurement using thin-plate weirs

KS B ISO 18320-2022 液体比重计.明渠液体流量的测量.水位-流量关系的测定

Hydrometry — Measurement of liquid flow in open channels — Determination of the stage–discharge relationship

KS B ISO 4365:2022 明渠中的液体流动.溪流和运河中的沉积物.浓度、粒度分布和相对密度的测定

Liquid flow in open channels — Sediment in streams and canals — Determination of concentration, particle size distribution and relative density

KS B ISO 18320:2022 液体比重计.明渠液体流量的测量.水位-流量关系的测定

Hydrometry — Measurement of liquid flow in open channels — Determination of the stage–discharge relationship

KS B ISO 18365-2022 水文测量.测量站的选择、建立和操作

Hydrometry — Selection, establishment and operation of a gauging station

KS B ISO 1438-2022 水文测量.用薄板堰测量明渠流量

Hydrometry — Open channel flow measurement using thin-plate weirs

KS B ISO 18365:2022 水文测量.测量站的选择、建立和操作

Hydrometry — Selection, establishment and operation of a gauging station

KS B ISO 4360:2022 水文测量.使用三角形断面堰测量明渠流量

Hydrometry — Open channel flow measurement using triangular profile weirs

KS B ISO 4365-2022 明渠中的液体流动.溪流和运河中的沉积物.浓度、粒度分布和相对密度的测定

Liquid flow in open channels — Sediment in streams and canals — Determination of concentration, particle size distribution and relative density