17.200.20 温度测量仪器仪表 标准查询与下载

PN-EN IEC 62828-5-2021-05 E 测试工业和过程测量变送器的参考条件和程序 第5部分：流量变送器的特定程序（IEC 62828-5:2020）

Reference conditions and procedures for testing industrial and process measurement transmitters -- Part 5: Specific procedures for flow transmitters (IEC 62828-5:2020)

T/CAQI 204-2021 红外非接触式人体表面温度快速筛查系统

基本要求、现场设置要求、性能要求、环境适应性要求、电气安全。

Non-contact system for instant screening of human skin temperature

ASTM E2758-15a(2021) 宽带 低温红外测温仪的选择和使用标准指南

Standard Guide for Selection and Use of Wideband, Low Temperature Infrared Thermometers

ASTM E207-21 通过与具有类似EMF温度特性的参考热电偶进行比较的单个热电偶材料的热EMF试验的标准试验方法

1.1 This test method covers a test for determining the thermoelectric electromotive force (emf) of a thermoelement versus National Instruments of Standards and Technology (NIST) platinum 67 (Pt-67) by means of measuring the difference between the emf of the test thermoelement and the emf of a reference thermoelement (previously referred to as a secondary standard), which has a known relationship to NIST Pt-67. 1.2 This test method is applicable to new thermocouple materials over the temperature ranges normally associated with thermocouples and their extension wires. The table on Suggested Upper Temperature Limits for Protected Thermocouples in Specification E230/E230M lists the ranges associated with the letter-designated types of thermocouples. ASTM MNL122 lists the temperature range of extension circuit materials. 1.3 This test method is not applicable to stability testing or inhomogeneity testing. 1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Thermal EMF Test of Single Thermoelement Materials by Comparison With Reference Thermoelement of Similar EMF-Temperature Properties

ASTM D7962-21 测量最小浸入深度的标准实践和温度传感器测量漂移的评估

1.1?This practice describes two procedures for use with temperature measurement devices. Methodology is described for determining minimum immersion depth for thermal sensors, in particular RTDs or similar temperature sensors. Included is a procedure for consistently preparing a

Standard Practice for Determination of Minimum Immersion Depth and Assessment of Temperature Sensor Measurement Drift

ASTM E77-14(2021) 温度计检验和验证的标准测试方法

1.1 This test method covers visual and dimensional inspection and test for scale accuracy to be used in the verification of liquid-in-glass thermometers as specified in Specifications E1 and E2251. However, these procedures may be applied to other liquid-in-glass thermometers.2 NOTE 1—The use of NIST SP250-232 is recommended. 1.2 Warning—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use caution when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law. Users must determine legality of sales in their location. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Inspection and Verification of Thermometers

ASTM D8164-21 石油产品 液体燃料和润滑剂测试用数字接触式温度计标准指南

1.1?The intent of this guide is to suggest an initial configuration and provide guidance when establishing the appropriate criteria needed for a DCT to correctly measure the temperature in a laboratory test method for products within the scope of this committee. This guide inclu

Standard Guide for Digital Contact Thermometers for Petroleum Products, Liquid Fuels, and Lubricant Testing

DS/EN IEC 60584-3:2021 热电偶 第3部分：延长和补偿电缆 公差和识别系统

Thermocouples – Part 3: Extension and compensating cables – Tolerances and identification system

NF C42-321-3*NF EN IEC 60584-3:2021 热电偶 第3部分：延长和补偿电缆 公差和识别系统

Thermocouples - Part 3 : extension and compensating cables - Tolerances and identification system

EN IEC 60584-3:2021 热电偶 第3部分：延长和补偿电缆 公差和识别系统

IEC 60584-3:2021 It is necessary for thermocouple temperature measurement that the electro-motive force (abbreviated as e.m.f. hereafter) of the thermocouple circuit is precisely measured by a measuring instrument. A thermocouple is electrically connected to the instrument by a proper pair of electric cables. IEC 60584-3:2021 standardizes these cables. It specifies identification and manufacturing tolerances for extension and compensating cables (mineral insulated extension and compensating cables are not included) provided directly to users of industrial processes. These tolerances are determined with respect to the e.m.f. ver-sus temperature relationship of IEC 60584-1. The requirements for extension and compensating cables for use in industrial process control are specified.

Thermocouples - Part 3: Extension and compensating cables - Tolerances and identification system

UNI EN ISO 80601-2-56:2021 医用电气设备 第 2-56 部分：体温测量用体温计的基本安全和基本性能的特殊要求

Medical electrical equipment - Part 2-56: Particular requirements for basic safety and essential performance of clinical thermometers for body temperature measurement

DIN EN 50212:2021 热电偶插接件; 德文版本EN 50212-2020

The object of this document is to determine composition, nature of materials, manufacturing tests and thermoelectronic behaviour, of connectors for sensors using thermocouples according to EN 60584-3:2008. This document does not cover such special thermocouples as U, L and W type

Connectors for thermoelectric sensors; German version EN 50212:2020

IEC 60584-3:2021 热电偶第3部分:扩展和补偿电缆 - 公差和识别系统

Thermocouples - Part 3: Extension and compensating cables - Tolerances and identification system

PN-EN 50212-2021-02 E 热电传感器连接器

Connectors for thermoelectric sensors

OVE EN IEC 60751:2021 工业用铂电阻温度计和铂温度传感器（IEC 65B/1187/CDV）（英文版）

Industrial platinum resistance thermometers and platinum temperature sensors (IEC 65B/1187/CDV) (english version)

ASTM E633-21 高温机械试验中热电偶使用的标准指南

1.1?This guide covers the use of ANSI thermocouple Types listed in Specification E230/E230M for elevated-temperature mechanical testing at temperatures typical in testing of metals. Note 1:?Typical conditions for mechanical testing are specified temperatures up to 1800 ��F (982 

Standard Guide for Use of Thermocouples in Elevated-Temperature Mechanical Testing

T/JAR 002/1-2021 数字温湿度记录仪

本团体标准针对数字温湿度记录仪，规定了数字温湿度记录仪测试应在15℃~35℃、相对湿度45%~75%、大气压力86kPa~106kPa的环境下进行，能提供日期的采集、记录和储存。本团体标准规定了数字温湿度记录仪的电源适用性、温湿度要求及抗干扰能力，对数字温湿度记录仪有一定规范作用。

Digital temperature and humidity recorder

CSA C22.2 No.24-2021 温度指示和调节设备

Temperature-indicating and -regulating equipment

KS A 0514-2020 填充系统温度计和双金属温度计的温度测量方法

Method of temperature measurement by filled-system thermometers and bimetaillic thermometers

KS B 5235-2020 蒸气压温度计

Vapour pressure thermometers