17.200.20 温度测量仪器仪表 标准查询与下载

ASTM E696-23 钨铼合金热电偶丝标准规范

1.1  This specification covers the requirements for bare, solid conductor, tungsten and rhenium alloy thermoelements having diameters of 0.127 mm (0.005 in.) to 0.508 mm (0.020 in.) supplied in matched pairs. These thermoelements shall be suitable for use either in bead-insulated, bare-wire thermocouples, or in compacted metal-sheathed, ceramic insulated thermocouple material or assemblies. 1.2  This specification covers the thermocouple combinations of tungsten-3 % rhenium versus tungsten-25 % rhenium (W3Re/W25Re) and tungsten-5 % rhenium versus tungsten-26 % rhenium (W5Re/W26Re; Type C). All information applies to both combinations unless otherwise noted. 1.3  It is recognized that the alloys described are refractory and are not suitable for use at high temperatures in oxidizing atmospheres. All tests and processes described herein must be performed under conditions that are non-reactive to tungsten-rhenium alloys. 1.4  The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Tungsten-Rhenium Alloy Thermocouple Wire

ASTM E585/E585M-23 压实矿物绝缘金属护套贱金属热电偶电缆的标准规范

1.1  This specification establishes requirements for compacted, mineral-insulated, metal-sheathed (MIMS), base metal thermocouple cable,2 with at least two thermoelements.3 1.2  This specification describes the required material, processing and testing requirements, optional supplementary testing, quality assurance, and verification choices. 1.3  The material of construction includes standard base metal thermoelements, austenitic stainless steel or other corrosion resistant sheath material, and either magnesia (MgO) or alumina (Al2 O3 ) insulation. 1.4  The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Compacted Mineral-Insulated, Metal-Sheathed, Base Metal Thermocouple Cable

ASTM E235/E235M-23 用于核能或其他高可靠性应用的 K 型和 N 型矿物绝缘金属护套热电偶的标准规范

1.1  This specification covers the requirements for simplex, compacted mineral-insulated, metal-sheathed (MIMS), Type K and N thermocouples for nuclear or other high reliability service. Depending on size, these thermocouples are normally suitable for operating temperatures to 1652 °F [900 °C]; special conditions of environment and life expectancy may permit their use at temperatures in excess of 2012 °F [1100 °C]. This specification was prepared to detail requirements for this type of MIMS thermocouple for use in nuclear environments, but they can also be used for laboratory or general commercial applications where the environmental conditions exceed normal service requirements. The intended use of a MIMS thermocouple in a specific nuclear application will require evaluation of the compatibility of the thermocouple, including the effect of the temperature, atmosphere, and integrated neutron flux on the materials and accuracy of the thermoelements in the proposed application by the purchaser. 1.2 This specification does not attempt to include all possible specifications, standards, etc., for materials that may be used as sheathing, insulation, and thermocouple wires for sheathed-type construction. The requirements of this specification include only the austenitic stainless steels and other alloys as allowed by Specification E585/E585M for sheathing, magnesium oxide or aluminum oxide as insulation, and Type K and N thermocouple wires for thermoelements (see Note 1 ). 1.3  General Design— Nominal sizes of the finished thermocouples shall be 0.0400 in., 0.0625 in., 0.125 in., 0.1875 in., or 0.250 in. [1.000 mm, 1.500 mm, 3.000 mm, 4.500 mm, or 6.000 mm]. Sheath dimensions and tolerances for each nominal size shall be in accordance with Table 1 and Figs. 1 and 2 . The measuring junction styles for thermocouples covered by this specification are as follows: FIG. 1 Grounded Measuring Junction, Style G FIG. 2 Ungrounded Measuring Junction, Style U 1.3.1  Style G2 (grounded) — The measuring junction is electrically connected to its conductive sheath, and 1.3.2  Style U2 (ungrounded) — The measuring junction is electrically isolated from its conductive sheath and from reference ground. 1.4  The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not exact equivalents or conversions; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Type K and Type N Mineral-Insulated, Metal-Sheathed Thermocouples for Nuclear or for Other High-Reliability Applications

T/JLA 005-2023 表面温度源性能测评方法

本文件规定了表面温度源性能特性、测评条件、测评项目和方法、测评结果表达。

Performance evaluation method for the surface temperature source

ASTM E1350-18(2023) 安装或维修之前和之后测试护套热电偶、热电偶组件和连接线的标准指南

Standard Guide for Testing Sheathed Thermocouples, Thermocouple Assemblies, and Connecting Wires Prior to, and After Installation or Service

ASTM E2593-17(2023) 工业铂电阻温度计精度验证标准指南

Standard Guide for Accuracy Verification of Industrial Platinum Resistance Thermometers

ASTM E3142-18a(2023) 热分析仪热滞后的标准测试方法

Standard Test Method for Thermal Lag of Thermal Analysis Apparatus

GSO ASTM E1061:2023 直读液晶额头温度计的标准规范

This specification covers the requirements and test methods for direct-reading liquid crystal forehead thermometers, in either the continuous or intermittent reading modes, designed to monitor trends or measure human forehead surface temperatures, or both. When examined by test methods recommended herein, each thermometer shall comply with thermal profile, temperature range, tolerance, sequencing, operating and storage environment, and labeling requirements.

Standard Specification for Direct-Reading Liquid Crystal Forehead Thermometers

GSO ASTM E1299:2023 用于间歇测定人体体温的可重复使用相变型发烧温度计的标准规范

  Scope is not provided for this standard

Standard Specification for Reusable Phase-Change-Type Fever Thermometer for Intermittent Determination of Human Temperature

ASTM E574-23 玻璃纤维或二氧化硅纤维绝缘的双相贱金属热电偶导线的标准规范

1.1 This specification sets forth the requirements for duplex, types E, J, K, N and T thermocouple wire, insulated with E-glass, S-glass, amorphous silica fiber or polycrystalline fiber. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Duplex, Base Metal Thermocouple Wire With Glass Fiber or Silica Fiber Insulation

ASTM E230/E230M-23 标准化热电偶的温度电动势（emf）表的标准规范

Standard Specification for Temperature-Electromotive Force (emf) Tables for Standardized Thermocouples

T/GDAQI 107-2023 耳温计

本文件规定了耳温计的产品组成、要求、试验方法、检验规则及标志、包装、运输和贮存。 本文件适用于通过探测器测量与被测对象耳腔之间的红外辐射交换和适当的修正值，输出显示身体某部位温度的耳腔式医用红外体温计（以下简称耳温计）。该耳温计通过耳腔的热辐射来显示被测对象的体温。

Ear thermometer

T/CASME 173-2023 热工控制系统用光纤光栅温度传感器

本文件规定了热工控制系统用光纤光栅温度传感器的结构、分类及参数、要求、试验方法、检验规则、标志、包装、运输和贮存。

Optical fiber grating temperature sensor temperature sensors for thermal control systems

T/GDAQI 102-2023 筛查用红外人体表面温度测量仪

本文件规定了筛查用红外人体表面温度测量仪的术语和定义、产品的分类、要求、试验方法、标志和随附文件、包装、运输、贮存的要求。 本文件适用于通过探测器以非接触方式测量人体表面红外辐射量和适当的修正值，输出被测人体部位温度，预期应用于民用公共场所筛查用的红外人体表面温度测量仪（以下简称测温仪）的设计定型、生产与出厂检验。不适用于医用红外额温计、分辨率大于320240的热成像仪等预期用于专业场所的产品。

Infrared devices of human skin temperature for instant screening

ASTM E1299-96(2023) 间歇测定人体温度用可重复使用的相变型体温计标准规范

1.1 This specification covers reusable phase-change-type clinical thermometers. 1.2 The following safety hazards caveat pertains only to the test method portion, Section 6, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Reusable Phase-Change-Type Fever Thermometer for Intermittent Determination of Human Temperature

ASTM E825-98(2023) 间歇测定人体温度用相变型一次性发热温度计的标准规范

1.1 This specification covers phase change-type clinical thermometers that are designed and intended for one-time use. 1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Phase Change-Type Disposable Fever Thermometer for Intermittent Determination of Human Temperature

ASTM D8055-23 D04道路和铺路标准中替代水银温度计的适当电子温度计的选择指南

1.1 The Interstate Mercury Education and Reduction Clearinghouse (IMERC) and the U.S. Environmental Protection Agency (EPA) are phasing out the use of mercury thermometers because of safety and environmental concerns. This guide was developed to support replacing mercury thermometers in D04 standards with appropriate electronic thermometers. 1.2 This guide provides assistance for the D04 subcommittees when selecting electronic thermometers for general use in water or oil baths and ovens and as possible replacements for Specification E1 mercury thermometers currently used in D04 road and paving standards. Guidance for using non-mercury liquid thermometers in place of mercury thermometers can be found in Specification E2251. 1.3 Some guidance is also provided for selecting a handheld infrared thermometer for use in field applications. 1.4 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this guide. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Selecting an Appropriate Electronic Thermometer for Replacing Mercury Thermometers in D04 Road and Paving Standards

DB11/T 2035-2022 供暖民用建筑室温无线采集系统技术要求

Technical requirements for room temperature wireless acquisition system for heating civil buildings

DB13/T 5645-2022 二端口N5242矢量网络分析仪维修技术规范

Technical specification for maintenance of two-port N5242 vector network analyzer

T/CASME 173-2022 热工控制系统用光纤光栅温度传感器

本文件规定了热工控制系统用光纤光栅温度传感器的结构、分类及参数、要求、试验方法、检验规则、标志、包装、运输和贮存。

Optical fiber grating temperature sensor temperature sensors for thermal control systems